Casaria Tami Sun Lounger

Introduction

Thank you for choosing a Casaria product. You have made an excellent choice. To meet our high quality standards, our products undergo regular inspections and comply with the stringent requirements of the European Union.

1.0 Symbols

IMPORTANT, KEEP FOR FUTURE REFERENCE: READ CAREFULLY!

Please read these instructions carefully and thoroughly before using the product for the first time. Keep these instructions for future reference. Should you pass the product on in future, make sure that you also include these instructions.

WARNING! POTENTIAL DANGER! ⚠️

Observe the safety information and set-up instructions to avoid any risk of injury or damage to the product.

RISK OF SUFFOCATION! ?

Keep small parts and packaging material out of the reach of children!

PRODUCT MODIFICATION ?

Never make modifications to the product! Modifications will invalidate the warranty and may make the product unsafe or, in the worst-case scenario, dangerous.

2.0 General Notes

• We recommend 1 to 2 people for assembly.
• Note: A suitable Phillips screwdriver is required for assembly.
• ATTENTION! Keep small children away during setup, as there is a risk of injury!
• Please note that screws should first of all be inserted by hand and only slightly tightened so that the screws find purchase and loosely connect the elements.
• Screws must only be fully tightened once all the elements are connected in this way. Subsequent tightening of the screws can compensate for minor discrepancies in drill holes that can be present in hand-finished products.
• Ensure that this product is fully assembled before use. Check that all screws and bolts are securely tightened. Do this on a regular basis.
• Do not screw the screws in too tightly as the material may become damaged and cracks may form.
• To maintain quality and also reduce the time and effort required for maintenance, we recommend protecting the product from the sun and rain and exposure to the elements. When not in use, you should store your product in a dry, protected place. We recommend using a suitable protective cover.
• Failure to carry out regular care and maintenance will significantly shorten the lifespan of your product. We cannot accept any liability for consequential damage resulting from lack of care and maintenance.
• Make sure that the product stands securely on a level, solid and load-bearing surface.
• Ensure that the folding mechanism is properly locked in place.
• Note: An initial cracking noise, e.g. when sitting on benches, is completely normal. These noises will subside with continued use.
• CAUTION! Keep fingers and limbs away from moving parts to prevent trapping!

3.0 Intended Use

The lounger is designed exclusively as seating and reclining furniture for indoor and outdoor use. The item must not be lifted or moved by a person during use.

Use the product only for its intended purpose. The manufacturer accepts no liability for damage caused by improper use. Any modification to the product may negatively impact safety, cause hazards and invalidate the warranty.

Only suitable for domestic use. Not for commercial use.

4.0 Unpacking Information

Open the box and remove the product. After unpacking, check the product for damage and make sure that it is complete. Subsequent complaints cannot be accepted.

This product is subject to rigorous testing and standards in accordance with EU directives so that we can offer you a product that is absolutely non-hazardous to your health. However, you may encounter a slight initial odour; this is not harmful to your health in any way. We recommend that you assemble the product in a well-ventilated environment. After the product has been taken out of its packaging, any odour will quickly disappear.

5.0 Maintenance and Care Information

Use a cloth and warm soapy water for cleaning. Do not use cleaners or detergents containing solvents; substances such as bleach can damage the product. You may find further care instructions on the product. Regular cleaning, checking and maintenance increase the item's safety and lifespan.

Wood care instructions

Before assembly, wash the wooden parts with lukewarm water and a light soap solution to remove any wood dust, excess oil or pre-treatment residues. Even natural hardwood products require regular care by oiling them at least twice a year.

Before re-oiling, rub the wood with fine sandpaper and clean as previously described. Then treat according to the instructions of your wood care product as before.

Damage caused by failure to treat the wood with oil is not covered by the warranty. Changes in surface colour, greying and small cracks are normal with natural products and are not grounds for complaint. Regularly treating your natural product with oil delays this process. By following these care instructions, you will be able to enjoy your new natural product for a long time to come.

Do not place wooden furniture directly on your lawn or porous surfaces. Despite oiling, the moisture from soil and grass can lead to mould growth or similar and damage your furniture. Hardwood furniture should not be left out in the rain for long periods of time. If you use a protective oil with colour pigments, it is possible for these pigments to wash off. We accept no liability for any consequently stained surfaces.

6.0 Technical Data

7.0 Disposal

At the end of your item's long service life, please dispose of the valuable raw materials appropriately so that proper recycling can take place. If you are unsure how best to proceed, local waste disposal companies or recycling centres will be happy to help.

Assembly Instructions

The following diagrams illustrate the assembly process. Please refer to the parts list for identification.

Step 1

Connect parts T-2, T-3, T-9, T-10 as shown in the diagram.

Step 2

Attach parts T-1, T-14, T-15 to the main frame as shown.

Step 3

Assemble segments T-C, T-E, and T-O using parts T-6, T-7, and T-11.

Step 4

Connect the frame segments using parts T-3 and T-12.

Step 5

Attach wheels using parts T-5 and T-8.

Step 6

Attach the backrest and seat components using parts T-F, T-G, and T-3.

Step 7

Connect the adjustable backrest mechanism using parts T-4, T-6, T-13, and T-P.

Step 8

Engage the locking mechanism for the adjustable backrest.

Step 9

Adjust the backrest to the desired position.

Step 10

The lounger is now ready for use.