Casaria Beer Tent Set Foldable 170cm
Article No.: 100048
Instructions
Thank you for choosing a Casaria product. Our products undergo regular inspections to ensure they meet high quality standards and comply with European Union requirements.
1.0 Symbols
IMPORTANT, KEEP FOR FUTURE REFERENCE: READ CAREFULLY!
Read these instructions carefully before first use. Keep for future reference. If passing the product to a third party, include these instructions.
WARNING! POTENTIAL DANGER!
Observe safety and assembly instructions to avoid injury or damage.
RISK OF SUFFOCATION!
Keep small parts and packaging material away from children!
PRODUCT MODIFICATION
Never modify the product. Modifications will invalidate the warranty and may make the product unsafe.
2.0 General Notes
- Assembly recommended for 1-2 people.
- ATTENTION! Keep children away during setup – risk of injury!
- Ensure the product is fully assembled before use.
- To maintain quality and reduce maintenance, protect the product from sun, rain, and weather. Store in a dry, protected place when not in use. A suitable protective cover is recommended.
- Failure to perform regular care and maintenance will significantly shorten the product's lifespan. No liability will be accepted for consequential damage resulting from lack of care and maintenance.
- Ensure the product stands securely on a level, solid, and load-bearing surface.
- Ensure the folding mechanism is properly locked.
- Note: Initial cracking noises, e.g., when sitting on benches, are normal and will subside with continued use.
- CAUTION! Keep fingers and limbs away from moving parts to prevent trapping!
3.0 Intended Use
The beer tent set is designed for indoor and outdoor use. Standing or sitting on the table is prohibited.
Use the product only for its intended purpose. The manufacturer accepts no liability for damage caused by improper use. Any modification to the product may negatively impact safety, cause hazards, and invalidate the warranty.
Only suitable for domestic use. Not for commercial use.
4.0 Unpacking Information
Open the box and remove the product. Check for completeness and damage. Subsequent complaints cannot be accepted.
This product is subject to rigorous testing and standards in accordance with EU directives, ensuring it is absolutely non-hazardous to health. A slight initial odor may occur but is not harmful. Assembly in a well-ventilated environment is recommended. The odor will disappear shortly after unpacking.
5.0 Maintenance and Care Information
Clean with a cloth and warm soapy water. Do not use cleaners or detergents containing solvents (e.g., bleach) as they can damage the product. Further care instructions may be available on the product. Regular cleaning, checking, and maintenance increase safety and lifespan.
Wood care instructions
Natural hardwood products must be oiled regularly for maintenance, at least twice a year.
Before re-oiling, treat the wood with fine sandpaper and clean as previously described. Then treat according to your wood care product's instructions.
Damage caused by failure to oil is not covered by the warranty. Surface color changes, greying, and small cracks are normal processes for natural products and are not grounds for complaint. Regular oiling delays these processes. Following these care instructions will ensure you enjoy your new natural product for a long time.
Hardwood furniture should not be left out in the rain for long periods. If you use an oil with color pigments, these may wash off. No liability is accepted for consequently stained surfaces.
6.0 Technical Data
Item Number | 100048 |
Material | Chinese fir wood + steel |
Table Size | 170 x 46 x 75 cm |
Bench Size | 170 x 23 x 46 cm |
Table Wood Thickness | 2.0 cm |
Bench Wood Thickness | 2.5 cm |
Metal Size | 27 x 27 x 2.0 mm |
Metal Thickness | 2.0 mm |
Umbrella Hole Size | 6.2 cm |
7.0 Disposal
At the end of your item's service life, dispose of the valuable raw materials appropriately for proper recycling. If unsure, contact local waste disposal companies or recycling centers.
Assembly
Ax1: Table frame
Bx2: Benches
Cx1: Umbrella
Step 1: Attach legs to the table frame (A).
Step 2: Attach legs to the benches (B).
Step 3: Assemble the table and benches.
Serviceportal
For any type of service, complaints, and technical support, you can confidently turn to our trained staff.