Corrigan Studio Desk with Hutch Assembly Instructions

Part Identification

Identify all parts before beginning assembly:

• 1. TOP (1)
• 2. UPRIGHT (1)
• 3. RIGHT END (1)
• 4. BOTTOM (1)
• 5. SHELF (1)
• 6. BACK (1)
• 7. LEG (4)
• 8. LEFT DRAWER SIDE (1)
• 9. RIGHT DRAWER SIDE (1)
• 10. DRAWER BACK (1)
• 11. DRAWER BOTTOM (1)
• 12. DRAWER FRONT (1)
• 13. DOOR (1)
• 14. BRACE (1)
• 15. LEFT LEG (2)
• 16. HUTCH LEFT END (1)
• 17. HUTCH LEFT BACK (1)
• 18. LEFT DIVIDER (2)
• 19. LEFT UPRIGHT (1)
• 20. LEFT SHELF (1)
• 21. HUTCH RIGHT BACK (1)
• 22. RIGHT DIVIDER (2)
• 23. RIGHT SHELF (1)
• 24. CENTER UPRIGHT (1)
• 25. HUTCH RIGHT END (1)

The diagram displays all numbered parts, showing their shapes and relative positions for assembly.

Hardware Identification

Identify all hardware before beginning assembly:

Diagrams show each type of hardware with its corresponding identifier and quantity.

Step 1

Attach hinge brackets (V) to part 2 using eight 5/8" flat head screws (R). Insert eight wood dowels (C) into the pre-drilled holes on parts 2 and 3. Connect part 3 to part 2 using two cam screws (B) and secure with cam locks (A).

Diagram shows part 2 and part 3 being joined. Hinge brackets (V) are attached to part 2 with screws (R). Wood dowels (C) are inserted into holes on both parts. Cam screws (B) are inserted into part 3 and secured by cam locks (A) in part 2.

Step 2

Insert two hidden cams (A) into the designated holes on part 2. Ensure the arrow on the hidden cam points towards the edge of the board. Attach part 14 to part 2 using the cam mechanism.

Diagram shows two circular insets illustrating the correct insertion of a hidden cam (A) into a panel. The arrow on the cam must point towards the edge of the board. Part 14 is shown being attached to part 2, with cam screws already inserted into part 14.

Step 3

Attach part 1 to the assembly using four cam screws (B).

Diagram shows part 1 being attached to the partially assembled structure. Four cam screws (B) are shown being inserted into part 1.

Step 4

Insert four hidden cams (A) into the designated holes on parts 2 and 3. Ensure the arrow on the hidden cam points towards the edge of the board. Attach parts 2 and 3 to the assembly using the cam mechanism.

Diagram shows two circular insets illustrating the correct insertion of a hidden cam (A) into a panel, with the arrow pointing towards the edge. Parts 2 and 3 are shown being attached to the main structure, likely connecting to part 1 or other components via cam locks.

Step 5

Secure the assembly using three 1-1/8" machine screws (Q).

Diagram shows the current assembly and indicates where three 1-1/8" machine screws (Q) are to be inserted to further secure the structure.

Step 6

Attach part 4 to the assembly using four 1-1/2" flat head screws (E).

Diagram shows part 4 being attached to the top of the structure. The edge of part 4 is labeled as "unfinished edge," indicating its orientation. Four 1-1/2" flat head screws (E) are used for attachment.

Step 7

Attach part 6 to the assembly using sixteen 3/4" NALLs (W).

Diagram shows part 6 being attached to the back of the structure. Sixteen 3/4" NALLs (W) are depicted being used for this attachment.

Step 8

Attach the four legs (7) to the bottom panel (4) using eight 1-3/4" machine screws (G), eight washers (M), and eight lock washers (N). Use the provided wrench (L) for tightening.

Diagram shows the bottom panel (4) with four legs (7) being attached. Each leg is secured with a machine screw (G), washer (M), and lock washer (N). A close-up view shows the order of assembly: screw, lock washer, washer, then into the leg and panel.

Step 9

Insert two wood dowels (C) into part 15. Attach part 15 to the assembly using four 1-3/4" machine screws (G), four washers (M), and four lock washers (N). Use the wrench (L) for tightening.

Diagram shows two circular insets. The first shows wood dowels (C) being inserted into part 15. The second shows part 15 being attached to the main structure using machine screws (G), washers (M), and lock washers (N).

Step 10

Attach six felt feet (K) to the bottom of the legs (7).

Diagram shows the underside of the desk legs (7) and indicates where the six felt feet (K) should be attached.

Step 11

Insert four cam screws (I) into part 12.

Diagram shows part 12 (Drawer Front) with four cam screws (I) being inserted into its back surface.

Step 12

Insert four hidden cams (H) into the designated holes on parts 8 and 9. Ensure the arrow on the hidden cam points towards the edge of the board. Attach parts 8 and 9 to part 12 using the cam mechanism.

Diagram shows two circular insets illustrating the correct insertion of a hidden cam (H) into a panel, with the arrow pointing towards the edge. Parts 8 (Left Drawer Side) and 9 (Right Drawer Side) are shown being attached to part 12 (Drawer Front) using cam locks.

Step 13

Attach part 11 (Drawer Bottom) to the drawer assembly.

Diagram shows part 11 being slid into place within the drawer structure, indicated by an arrow and the label "finished".

Step 14

Secure the drawer assembly using four 1-1/2" flat head screws (E).

Diagram shows the drawer assembly and indicates where four 1-1/2" flat head screws (E) are to be inserted to secure part 10 (Drawer Back) to the drawer sides.

Step 15

Attach the pull (J) to the drawer front (12) using two 1/2" machine screws (F).

Diagram shows the drawer front (12) and the pull (J). Two 1/2" machine screws (F) are shown being used to attach the pull to the drawer front.

Step 16

Install the drawer slides. Be sure to pull out the inner slide from the cabinet member, include the silver socket. Align and slide drawer members into cabinet members. You will easily slide the drawers!

Diagram shows the desk with a drawer partially extended. Two circular insets show the process of aligning and inserting drawer slides. One inset shows a correct alignment with a checkmark (✔️), and two show incorrect alignments with crosses (❌). The text "The arrow must point toward the dege of the board" is also present, referring to slide orientation.

Step 17

Insert four metal pins and rubber sleeves (S) into part 5.

Diagram shows part 5 (Shelf) and indicates where four metal pins and rubber sleeves (S) are to be inserted, likely for shelf support or attachment.

Step 18

Attach two hinges (U) to part 13 (Door) using four 5/8" flat head screws (R). Attach the door pull (T) to the door using one 7/8" machine screw (X).

Diagram shows part 13 (Door). Two hinges (U) are attached to the door using screws (R). A pull (T) is attached to the door using screw (X).

Step 19

Attach the door hinges to the desk cabinet. Adjust the door using the adjusting screws (horizontal and depth) and vertical adjustment screws on the hinges.

Diagram shows the desk with the door (13) being attached to the cabinet. Close-up views of the hinges show adjusting screws for horizontal alignment, depth adjustment, and vertical adjustment, along with the mounting screws.

Step 20

Install the USB port (O) into the desk surface. Attach the drawer pull (J) to the drawer front using two 3/4" machine screws (D).

Diagram shows the desk surface with the USB port (O) being inserted into a pre-drilled hole. It also shows a drawer being fitted with a pull (J) using screws (D).

Step 21

Assemble the hutch components. Attach parts 16, 19, 20, 23, 24, 25 using cam screws (B) and wood dowels (C).

Diagram shows various hutch parts (16, 19, 20, 23, 24, 25) laid out. Cam screws (B) and wood dowels (C) are shown, indicating their use in connecting these components.

Step 22

Attach part 20 to parts 18 and 19 using four 1-1/2" flat head screws (E).

Diagram shows part 20 being attached to two parts labeled 18 and one part labeled 19. Four 1-1/2" flat head screws (E) are used for this connection.

Step 23

Insert one hidden cam (A) into the designated hole on part 20. Ensure the arrow on the hidden cam points towards the edge of the board. Attach part 19 to part 20 using the cam mechanism.

Diagram shows two circular insets illustrating the correct insertion of a hidden cam (A) into a panel, with the arrow pointing towards the edge. Part 19 is shown being attached to part 20 using cam locks.

Step 24

Attach parts 22 to part 23 using four 1-1/2" flat head screws (E).

Diagram shows two parts labeled 22 being attached to part 23. Four 1-1/2" flat head screws (E) are used for this connection.

Step 25

Insert one hidden cam (A) into the designated hole on part 23. Ensure the arrow on the hidden cam points towards the edge of the board. Attach part 21 to part 23 using the cam mechanism. Secure the assembly with two 1-1/2" flat head screws (E).

Diagram shows two circular insets illustrating the correct insertion of a hidden cam (A) into a panel, with the arrow pointing towards the edge. Part 21 is shown being attached to part 23 using cam locks. Two 1-1/2" flat head screws (E) are also shown being used.

Step 26

Insert one hidden cam (A) into the designated holes on parts 21 and 23. Ensure the arrow on the hidden cam points towards the edge of the board. Attach part 24 to parts 21 and 23 using the cam mechanism. Secure the assembly with two 1-1/2" flat head screws (E).

Diagram shows two circular insets illustrating the correct insertion of a hidden cam (A) into a panel, with the arrow pointing towards the edge. Part 24 is shown being attached to parts 21 and 23 using cam locks. Two 1-1/2" flat head screws (E) are also shown being used.

Step 27

Attach part 17 to parts 19 and 20 using three 1-1/2" flat head screws (E).

Diagram shows part 17 being attached to parts 19 and 20. Three 1-1/2" flat head screws (E) are used for this connection.

Step 28

Insert three hidden cams (A) into the designated holes on part 17. Ensure the arrow on the hidden cam points towards the edge of the board. Attach part 21 to part 17 using the cam mechanism.

Diagram shows two circular insets illustrating the correct insertion of a hidden cam (A) into a panel, with the arrow pointing towards the edge. Part 21 is shown being attached to part 17 using cam locks.

Step 29

Insert six hidden cams (A) into the designated holes on parts 16 and 25. Ensure the arrow on the hidden cam points towards the edge of the board. Attach the hutch assembly to the desk top using the cam mechanism.

Diagram shows two circular insets illustrating the correct insertion of a hidden cam (A) into a panel, with the arrow pointing towards the edge. Parts 16 and 25 are shown being attached to the desk top using cam locks.

Step 30

Peel a CAM COVER from the CAM COVER CARD (P) and stick one onto each visible HIDDEN CAM. This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.

Diagram shows the completed desk with hutch. Weight capacities are indicated on different surfaces (10 lbs, 50 lbs, 15 lbs, 20 lbs). It also shows the CAM COVER CARD (P) and illustrates applying the covers to the visible hidden cams.

Safety Warnings and Precautions

Please use your furniture correctly and safely. Improper use can cause safety hazards or damage to your furniture or household items. Carefully read the following:

1-Year Limited Warranty

This product comes with a 1-year limited warranty from the date of purchase, covering defects in materials or workmanship of components. The warranty does not cover damage resulting from improper assembly, misuse, abuse, or lack of maintenance. The exclusive remedy is repair or replacement of defective components. The manufacturer is not liable for incidental or consequential damages. Warranties may vary by state.