ELAC Debut ConneX DCB41-DS Owner's Manual

Introduction

This manual provides instructions for the ELAC Debut ConneX DCB41-DS powered speakers. Please read all instructions carefully before use and keep them for future reference.

Package Contents

The package includes:

• Remote Control
• Batteries x 2
• Stand x 2
• Rubber Foot x 4
• Grille x 2
• Power Cord
• Speaker Cable
• HDMI Cable

Connections

Connecting Speakers: Connect the speakers together using the supplied speaker wire.

Connecting Sources:

• Connect your TV, Computer, or Phono device using the appropriate cables.
• Connect your Bluetooth device wirelessly.
• Connect the AC mains power cord to the speaker and a power outlet.

Diagrammatic Representation of Connections:

A diagram illustrates connecting two speakers, a source device (TV, laptop, turntable, or Bluetooth device), and the AC power.

Controls and Inputs/Output

The rear panel of the speaker features various inputs and controls:

1. AC Mains Inlet
2. HDMI (ARC) Input
3. Volume/Power/Source control knob
4. L/R Switch
5. USB for Update
6. Ground Screw Terminal
7. USB Audio Input
8. Optical Input
9. Subwoofer Output
10. Phono/Line Switch
11. Phono/Line Input
12. Speaker Output

Volume Knob Operation:

• Rotate: Increases or decreases volume.
• Push: Turns the unit on. Press and hold in BT input to initiate pairing. Press when the unit is on to change input.

Front LED Colors:

• BT: Blue
• HDMI: Green
• USB: White
• Optical: Red
• Phono: Pink

Power/Standby: The unit enters standby mode after 15 minutes of inactivity. Pressing or rotating the volume knob, or pressing the power button on the remote, will wake the unit.

XBASS Feature

XBass is a proprietary circuit designed to enhance low-frequency performance.

To Turn ON/OFF: Press and hold the XBass button on the remote for 2 seconds. The LED display will blink once for OFF and twice for ON. When ON, pressing XBass will cycle through XBass settings. XBass can be turned off completely when connecting a subwoofer.

Turntable Connection

When connecting a turntable:

• If the turntable has a built-in phono pre-amplifier, ensure it is set to OFF, and the DCB41 is set to ON.
• If you are using an external phono pre-amplifier or the turntable's phono pre-amplifier is set to ON, ensure the DCB41's switch is set to ON position and the DCB41 is set to OFF.
• The ground connection is optional but recommended to reduce residual noise.

Television Connection

The speakers can be connected to a television via HDMI or Optical cable. HDMI supports eARC and ARC inputs from most televisions. Your television remote may control the power, mute, and volume of the Debut ConneX speakers.

Subwoofer Connection

A subwoofer can be connected to the Subwoofer Output on the rear panel.

Computer Connection

Connect to your USB devices using a USB Type B cable (printer cable).

Bluetooth Connection

Pairing:

• When the unit powers on, the BT LED will flash if no device is paired.
• When the LED is flashing, "ELAC DCB41" will be visible on your device's Bluetooth list.
• Pairing can be initiated by pressing and holding the BT source on the remote until the LED flashes.
• Alternatively, press and hold the rear volume button on the speaker in BT input until the LED flashes.

Remote Control

The remote control allows for:

• Power ON/OFF
• Source Selection (BT, Optical, USB, Phono, HDMI)
• Volume Control (Up/Down)
• XBass Control
• Previous/Next (for Bluetooth)
• Mute
• LED Intensity Adjustment

Setting Left or Right Speaker

The L/R switch (labeled '4' in diagrams) determines the speaker output assignment.

• If the L/R switch is set to "L", the speaker output (labeled '12' in diagrams) will function as the LEFT speaker.
• If the L/R switch is set to "R", the speaker output (labeled '12' in diagrams) will function as the RIGHT speaker.

General Information and Safety

1. General Information: Please read and follow all safety instructions. Keep them for future reference. Check the speaker for damage before use. Ensure the speaker is in perfect working condition.
2. Use Only as Directed: Connect speakers according to the manual. Many ELAC speakers have spikes or anti-slip feet for leveling. Adjust these for uneven floors to maintain perfect vertical alignment and stability.
3. Location: Install speakers on a level surface. Avoid locations with direct sunlight, high humidity, vibrations, extreme temperatures, or proximity to CRT televisions (due to magnetic shielding) or magnetic cards.
4. WARNING: Ensure product stability to prevent tip-over injuries. Spikes can increase stability on carpets but have sharp ends. Use Velcro or double-sided tape for slippery floors. Do not install near heat sources or in areas with explosion risk. Do not block ventilation openings. Avoid closed racks or cupboards. Do not place candles near the speaker. Avoid installing near transformers, as electromagnetic fields can cause hum. Certain materials may cause imprints from anti-slip feet or spike washers.