ELAC Debut Connex DCB61 Owner's Manual

Introduction

Congratulations on bringing home an ELAC Debut ConneX Powered Speaker System.

PREMIUM SOUND: Simplicity and Versatility!

Thank you for purchasing the ELAC DCB61 speakers. We appreciate your choice and trust in our product, and are confident you will enjoy the exceptional sound quality and performance they offer.

The Debut ConneX DCB61 powered bookshelf speakers exemplify simplicity in delivering a premium audio experience for both movies and music. Featuring a wide variety of inputs (HDMI ARC, Analog/Phono, Optical, USB, and Bluetooth), and matched with optimally designed drivers and amplifiers, the DCB61 delivers a truly exceptional audio experience.

JOURNEY TOGETHER THROUGH - THE LIFE OF SOUND

Contents

This manual covers the following items and features:

• Remote Control
• Batteries
• Rubber Foot
• Power Cord
• Speaker Cable
• HDMI Cable

Connections

General Connection Overview

The diagram illustrates the basic connection steps: 1. Connect speakers together with the supplied wire. 2. Connect your audio source (e.g., TV, Computer, Phono). 3. Connect your Bluetooth source. 4. Connect to AC mains power.

Turntable Connection

This section details connecting a turntable. It shows the rear panel inputs and outputs, including Phono/Line input, Ground terminal, and Audio Out from a turntable. Notes explain how to set the turntable's pre-amplifier (OFF or ON) and the DCB61's Phono/Line switch (ON or OFF) depending on whether the turntable has a built-in pre-amplifier. The ground connection is optional but recommended to reduce noise.

Television Connection

This section describes connecting to a television. It shows connections via HDMI ARC or Optical cable. A note indicates that HDMI supports eARC and ARC inputs from most televisions, and that the TV remote can control power, mute, and volume of the DEBUT ConneX.

Subwoofer Connection

This section illustrates connecting an active subwoofer to the Subwoofer Output on the rear panel of the DCB61.

Computer Connection

This section shows how to connect to a computer using a USB Type B cable (often referred to as a printer cable).

Firmware Update

To update the firmware:

1. Ensure the unit is powered off and plug in the USB drive containing the firmware file.
2. Turn the unit power on.
3. The update will start, and the LED indicator will blink. Do not unplug or power off the unit during the update.
4. The update is complete when the LED stops blinking.
5. Turn off the power, wait for 3 minutes, then turn the unit back on.

Caution: The unit may become unusable ("bricked") if unplugged or powered off during an update. If this occurs, repeat steps 2 through 5.

Bluetooth Connection

When powered on for the first time, the BT LED will flash if no device is paired. When flashing, "ELAC DCB61" should be visible on your device for pairing.

Pairing can also be initiated by:

• Pressing and holding the BT source button on the remote until the LED flashes.
• Pressing and holding the rear volume button on the speaker when in BT input until the LED flashes.

Setting Left or Right Speaker

The L/R switch (labeled '4' on the rear panel) determines the speaker output assignment.

• If the L/R switch is set to "L", speaker output 12 will be the LEFT speaker.
• If the L/R switch is set to "R", speaker output 12 will be the RIGHT speaker.

Note: This switch setting is only read during power on.

Controls and Inputs/Output

The rear panel of the ELAC Debut ConneX DCB61 features various controls and connection points:

• 1. AC Mains Inlet: Power connection.
• 2. HDMI (ARC) Input: For connecting to TVs with HDMI ARC.
• 3. Volume/Power/Source Knob: This knob controls volume, powers the unit on/off, and allows changing the input source.
• 4. L/R Switch: Selects whether the speaker acts as Left or Right.
• 5. USB for Update: Port for firmware updates.
• 6. USB Audio Input: For connecting audio sources via USB.
• 7. Optical Input: For connecting audio sources via optical cable.
• 8. Subwoofer Output: Connection for an active subwoofer.
• 9. Phono/Line Switch: Selects between Phono and Line level input for the Phono/Line input.
• 10. Phono/Line Input: Analog audio input, switchable between Phono and Line level.
• 11. Ground Screw Terminal: For turntable ground connection.
• 12. Speaker Output: Terminal for connecting the passive speaker or the other active speaker.

Volume Knob Operation:

• Rotate: Increases or decreases volume.
• Push: Powers the unit on. Press and hold while in BT input to initiate pairing. Press when the unit is on to change the input source.

Front LED Colors:

• BT: Blue
• HDMI: Green
• USB: White
• Optical: Red
• Phono: Pink

Power/Standby: The unit enters standby mode after 15 minutes of inactivity. It can be woken up by pressing or rotating the volume knob, or by pressing the power button on the remote control.

XBASS

XBASS is a proprietary circuit designed to enhance low-frequency performance.

To Turn ON/OFF: Press the XBass button on the remote control.

• LED display will blink Red for OFF.
• LED display will blink Green for ON.

Remote Control

The remote control provides access to various functions:

• Power ON/OFF: Turns the unit on or off.
• BT Source: Selects Bluetooth input.
• XBASS: Toggles the XBass feature.
• Previous (◄◄): Skips to the previous track.
• Next (►►): Skips to the next track.
• Adjust LED Intensity: Controls the brightness of the front LED.
• Optical Source: Selects Optical input.
• USB Source: Selects USB input.
• Phono Source: Selects Phono input.
• Mute: Mutes or unmutes the audio.
• Volume Down (-): Decreases volume.
• Volume Up (+): Increases volume.
• HDMI Source: Selects HDMI ARC input.

The manual also lists "Hex Codes" for remote control functions, presented as a grid of codes (e.g., 1A, OD, 3E, 23, 21, 22, 1F, OC, 12, OF, 06, 01, 03, 19).

General Information

General Information

• Please read and follow all safety instructions. Keep them safe for future reference.
• Observe all warnings on the speaker and in the manual. Check the speaker for damage before use.
• The speaker must be in perfect working condition. Damaged parts may lead to personal injury.

Use Only As Directed

• Connect the speaker(s) according to the instructions in this manual.
• ELAC speakers may be equipped with spikes and/or anti-slip feet for leveling. Adjust these by unscrewing them 2-3 turns for uneven floors. Ensure the speaker remains in perfect vertical alignment for stability to prevent tip-over.

Location

Install speakers on a level surface only. Avoid locations that are:

• In direct sunlight
• Very humid
• Prone to vibrations
• Exceptionally hot or cold
• Near CRT Televisions (speakers are not magnetically shielded and may cause color issues).
• Close to magnetic cards (may cause them to fail).

WARNING!

• Ensure the product is stable to avoid tip-over injuries. Spikes can improve stability on carpets but have sharp ends; handle with care. Use Velcro or double-sided tape for stability on slippery floors.
• Do not install near heat sources (radiators, stoves, amplifiers) or in areas with explosion risk.
• Do not block ventilation openings. Install according to manufacturer instructions.
• Do not install in closed racks or cupboards.
• Do not place burning candles on or near the speaker.
• Do not install near transformers, as electromagnetic fields can cause hum noise on woofers.
• Certain materials, lacquers, or surfaces may experience colored imprints from anti-slip feet or spike washers.

Company Information

ELAC AMERICAS INC.
1938 N. BATAVIA St. SUITE K
ORANGE, CA 92865

ELAC ELECTROACUSTIC GMBH
FRAUNHOFERSTRABE 16
D-24118 KIEL, GERMANY