ELAC DEBUT ConneX DCB41

The life of sound.

An illustration shows a pair of ELAC DEBUT ConneX DCB41 bookshelf speakers.

What's Included

• Remote Control
• Batteries
• Rubber Foot
• Power Cord
• Speaker Cable
• HDMI Cable

Connections

Setup Steps

1. Connect speakers together with supplied wire.
2. Connect source - TV, Computer, Phono.
3. Connect source - Bluetooth.
4. Connect AC mains.

Diagram illustrating the connection process. Step 1 shows the two speakers connected. Step 2 shows connections from a TV, Computer, and Turntable to the speakers. Step 3 shows a Bluetooth connection. Step 4 shows the power cord connecting to the speaker and a wall outlet.

Connecting to Television

The DEBUT ConneX can be connected to a television via HDMI (ARC) or Optical cable. HDMI supports eARC and ARC inputs from most televisions. The TV remote may control power, mute, and volume.

Diagram shows a TV connected to the HDMI (ARC) input and an alternative connection via Optical input.

Connecting a Subwoofer

Connect an active subwoofer to the Subwoofer Output on the rear panel.

Diagram shows the Subwoofer Output connected to the input of an active subwoofer.

Connecting to a Computer

Connect your computer to the USB Audio Input using a USB Type B cable (printer cable).

Diagram shows a laptop connected to the USB Audio Input with a USB Type B cable.

Connecting via Bluetooth

When powered on, the BT LED will flash if no device is paired. When flashing, 'ELAC DCB41' will be visible on your device for pairing.

Pairing can be initiated by:

• Pressing and holding the BT Source button on the remote until the LED flashes.
• Pressing and holding the rear volume knob on the speaker when in BT input until the LED flashes.

Diagram shows the Bluetooth symbol and aptX logo.

Controls and Operation

Rear Panel Overview

The rear panel of the ELAC DEBUT ConneX DCB41 features various ports and controls:

• 1. AC Mains Inlet: For connecting the power cord.
• 2. HDMI (ARC) Input: For connecting to TVs with ARC support.
• 3. Volume/Power/Source Knob: Multifunction knob for volume adjustment, power on/off, and input selection.
• 4. L/R Switch: Selects whether the speaker is the Left or Right channel.
• 5. USB for Update: For firmware updates.
• 6. Ground Screw Terminal: For turntable ground connection.
• 7. USB Audio Input: For connecting audio sources via USB.
• 8. Optical Input: For digital audio connections.
• 9. Subwoofer Output: For connecting an active subwoofer.
• 10. Phono/Line Switch: Selects input sensitivity for Phono or Line sources.
• 11. Phono/Line Input: RCA inputs for turntables (Phono) or other line-level sources.
• 12. Speaker Output: Terminals for connecting the passive speaker to the active speaker.

Volume Knob Operation

Rotate: Rotating the knob increases or decreases volume.

Push: Press to turn the unit on. Press and hold in BT input to initiate pairing. Press when the unit is on to change input.

Front LED Indicators

Front LED colors indicate the current status:

• BT: Blue
• HDMI: Green
• USB: White
• Optical: Red
• Phono: Pink

Power/Standby

The unit will enter standby mode after 15 minutes of inactivity. It can be woken up by pressing or rotating the volume knob, or by pressing the power button on the remote.

Remote Control

The remote control provides access to various functions:

• Power ON/OFF: Turns the unit on or off.
• BT Source: Selects Bluetooth input.
• XBASS: Activates/deactivates the XBass feature.
• Previous (BT) / Next (BT): Skips tracks in Bluetooth mode.
• LED: Adjusts LED intensity.
• Optical Source: Selects Optical input.
• Phono Source: Selects Phono input.
• USB Source: Selects USB Audio input.
• Mute: Mutes/unmutes audio.
• Volume Down / Volume Up: Adjusts volume.
• HDMI Source: Selects HDMI input.

Speaker Setup

Setting Left or Right Speaker

The L/R switch (4) on the rear panel determines the speaker's role. If set to 'L', the speaker output (12) will be the LEFT speaker. If set to 'R', the speaker output (12) will be the RIGHT speaker.

Diagram shows the rear panel with the L/R switch (4) and Speaker Output terminals (12) highlighted.

Features

XBASS

XBASS is a proprietary circuit designed to enhance low-frequency performance.

Turn ON/OFF: Press and hold the XBass button on the remote for 2 seconds. The LED display will blink once for ON and twice for OFF. When XBass is ON, pressing the XBass button cycles through XBass settings. XBass can be turned off completely when connecting a subwoofer.

Turntable Connection

To connect a turntable:

Ensure the turntable's built-in phono pre-amplifier is set to OFF and the DCB41's Phono/Line switch (10) is set to ON if using the DCB41's phono stage. If using the turntable's pre-amplifier, set its switch to ON and the DCB41's switch to OFF.

The Ground connection (6) is optional but recommended to reduce residual noise.

Diagram shows a turntable connected to the Phono/Line Input (11) and Ground Screw Terminal (6) on the speaker. An optional ground wire is shown. The Phono/Line switch (10) is indicated.

General Information and Safety

General Information

• Please read and follow all safety instructions.
• Keep instructions for future reference.
• Observe all warnings on the speaker and in the manual. Check the speaker for damage before use.
• The speaker must be in perfect working condition; damaged parts may cause personal injury.

Use

• Connect the speaker(s) according to the manual's instructions.
• ELAC speakers may have spikes or anti-slip feet for leveling. For uneven floors, adjust these by 2-3 turns of thread. Ensure perfect vertical alignment for stability; do not compromise stability by altering these feet, as the speaker may tip over.

Location

• Install speakers on a level surface only.
• Avoid placing speakers in locations that are:
• In direct sunlight
• Very humid
• Prone to vibrations
• Exceptionally hot or cold
• Near CRT Televisions (speakers are not magnetically shielded and may cause color issues).
• Close to magnetic cards (which may be damaged by the unshielded speakers).

Warnings

• Ensure the product is stable to prevent tip-over injuries. Spikes can improve stability on carpets; use caution with their sharp ends. Velcro or double-sided tape can improve stability on slippery floors.
• Do not install near heat sources (radiators, stoves, amplifiers) or in areas with explosion risk.
• Do not block ventilation openings. Install according to manufacturer instructions.
• Do not install in a closed rack or cupboard.
• Do not place burning candles on or near the speaker.
• Avoid placing speakers near transformers, as stray electromagnetic fields can cause hum noise on woofers.
• Certain materials, lacquers, or surfaces may show colored imprints from anti-slip feet or spike washers.
• NOTICE: RISK OF ELECTRIC SHOCK
• NOTICE: RISK OF ELECTRIC SHOCK - DO NOT OPEN

Contact Information

ELAC AMERICAS INC.
1938 N. BATAVIA St. SUITE K
ORANGE, CA 92865

ELAC ELECTROACUSTIC GMBH
FRAUNHOFERSTRABE 16
D-24118 KIEL, GERMANY