UPLIFT V3 Standing Desk - FV3-200 C-Frame Assembly and Operation Guide

Safety and Warnings

WARNING: Read all instructions before assembly. Failure to assemble or operate the desk properly may result in damage or personal injury. Retain this manual for future reference or new owners.

WARNING: Keep fingers and body parts clear of the moving desk. Check the desk's surroundings on all sides before raising or lowering the desk to ensure there are no obstacles that can cause damage or personal injury.

WARNING: Ensure all desk and accessory cords have enough slack so they don't pull as the desk moves up and down.

WARNING: Keep children away from the desk unless supervised. Misuse of the desk can cause personal injury. If children cannot be supervised at all times, use the desk keypad's safety lock feature or remove the power cord to prevent operation.

WARNING: Risk of serious injury or death. Adjusting the height of the desk could pinch or crush body parts trapped between the desktop, frame, or accessories and the floor or any stationary objects under the desk. Ensure that any body part under the desk or accessories are removed from any pinch or crush zones prior to moving the desk.

WARNING: Be sure there is a gap of at least 1" between the moving parts of the standing desk and objects located adjacent to it to avoid pinching and crushing hazards. Move the desk through its full range of motion to ensure a gap of 1" or more is maintained around the perimeter of the desk.

WARNING: The desk is designed for indoor use only. Use of desk outdoors or in damp locations can damage the desk and can cause risk of electric shock and/or fire.

WARNING: There is a risk of desk failure or electric shock if desk components become wet. If liquid is spilled on any electrical desk component, disconnect the desk from power immediately. Clean up the spill with a dry cloth and plug the desk back into the power outlet.

WARNING: Only plug the desk into a properly grounded 100-240V power outlet. Using a voltage converter is considered improper use and can cause damage to the desk.

WARNING: Do not open or insert any object into the desk legs or control box. Doing so may cause damage and can cause risk of electric shock.

WARNING: Never use the desk if the power cord or plug becomes damaged to avoid risk of fire and/or electric shock. Contact UPLIFT Desk for a replacement power cord if it is damaged in any way.

WARNING: Persons with limited mental or physical capabilities who are unable to comprehend the safe operation of the height adjustability feature must not operate the desk.

WARNING: Inspect the desk regularly and stop using immediately if you notice damaged or loose parts. Only replace damaged desk parts with authorized UPLIFT Desk parts.

Please read these instructions carefully. This desk is height adjustable to fit the user's height. Inappropriate use of this desk can cause property damage and/or bodily injury. Under no circumstances does the manufacturer accept warranty or liability claims for damages caused from improper use of this product. Provide this manual to any new user.

Keep a vertical gap of greater than 1" between items on desk and any obstructions above.

Keep a horizontal gap of greater than 1" from desk to wall and other furniture.

Do not place feet on items below the desk where they can be injured.

Package Contents

The following parts are included:

Crossbar End

qty 2

Crossbar Rail

qty 2

Control Box

qty 1

Leg Extension Cable

qty 1

Leg

qty 2

Side Bracket

qty 2

Foot

qty 2

Power Cord

qty 1

Keypad

qty 1 (Keypad varies, ships in separate box)

Above parts ship pre-assembled as shown below.

Hardware

M8 x 16 Screw

qty 8 (pre-installed in Feet & Side Brackets)

M10 x 8 Set Screw

qty 8 (pre-installed in Crossbar Ends)

#10-24 x 5/8" Truss Head Screw

qty 8

#10 x 5/8" Wood Screw

qty 4

Logo Plate

qty 2

Cable Management

FlexMount Cable Manager

qty 2

Cable Manager Bracket

qty 2

Hook & Loop Strip

qty 10

Cable Mount

qty 10

Keypad Cable Channel

qty 1

Tools Required

• 5mm Allen Wrench (included)
• Phillips Screwdriver

Assembly Instructions

The following steps detail how to assemble the C-Frame desk. For T-Frame assembly or using your own desktop, please refer to the specific instructions available via QR codes or online.

Before discarding any packaging, lay out all parts and verify that every item listed in the package contents is present. If a part seems to be missing, check all boxes carefully. If still missing, contact UPLIFT Desk support at (800) 349-3839 or support@upliftdesk.com before starting assembly.

Place the desktop on a clean surface with the mounting holes facing upward. Position the Crossbar End and Crossbar Rail assembly on the desktop approximately where shown. The Control Box can be positioned on either the left or right side.

Loosen Set Screws indicated by arrows using the Allen Wrench. Slide the Crossbar Ends apart and align the oval holes with the "C-frame crossbar end holes" shown on the Desktop Hole Layout (refer to page 4). Partially insert a #10-24 x 5/8" Screw in each hole with a Phillips screwdriver. Do NOT tighten these screws yet.

Insert a Leg into the slots of each Crossbar End as shown. If needed, slide Crossbar Rails toward the middle so they don't block the Crossbar End slots.

Place the left and right Side Brackets as shown. Align Side Bracket screws with Leg holes and insert using the Allen Wrench. Make sure these screws are tight!

Align oval holes in Side Brackets with the "Side bracket holes" shown on the Desktop Hole Layout (refer to page 4). Use a Phillips screwdriver to insert a #10-24 x 5/8" Screw into each hole. Make sure these screws are tight!

Center the Crossbar Rails between the Crossbar Ends using the indicator marks. Tighten the eight M10 x 8 Set Screws and the two #10-24 x 5/8" Screws indicated by the arrows.

Place a Foot on each Leg as shown. Align screws in Feet with Leg holes and insert using the Allen Wrench. Make sure these screws are tight! Ensure the long end of the foot faces toward the front of the desk.

The Keypad can be attached to either the right or left side of the desktop (right side is most popular). Choose a side, then insert two #10 x 5/8" Wood Screws with a Phillips screwdriver into the "Keypad holes" shown on the Desktop Hole Layout (refer to page 4). Do not overtighten the screws to avoid stripping.

To manage the keypad cable, separate the top and bottom halves of the Keypad Cable Channel. Peel the backing off the bottom half and press it onto the desktop about 3" to 4" behind the Keypad. Route the Keypad cable through the bottom half and reattach the top.

Note: Keypad and Control Box may be on opposite sides of the desk when assembled.

1. Connect the Power Cable to the AC port on the Control Box.
2. Connect the cable from the Leg closest to the Control Box to the M1 port.
3. Connect the cable from the opposite Leg to the Leg Extension Cable, which is pre-connected to the M2 port.
4. Connect the Keypad cable to the HS port.

Peel backing off Cable Mounts and press them onto the desktop. Recommended locations are shown. Thread a Hook & Loop Strip through the Cable Mount, bundle cables, and secure. Hook & Loop Strips can also be used without Cable Mounts by sliding them under or through the Crossbar Rails.

To optionally install casters, unscrew leveling glides counterclockwise, then screw in casters clockwise until tight. Before flipping the desk over, install any other accessories that attach to the desk frame or bottom of the desktop, such as desk drawers, keyboard trays, CPU holders, and surge protectors.

Refer to the separate instructions provided for the FlexMount Cable Manager for installation. Install only the Cable Manager Brackets first, then complete the rest of the assembly steps after the desk is flipped upright.

Caution: Be aware of cables and attached accessories as you flip the desk over. Gradually lift the front of the desk until the back of the Feet rest on the floor, then adjust your grip and rotate the desk upright.

Before attaching Logo Plates, use the Allen Wrench to tighten Side Bracket screws once again. This step is very important, do not skip! Align Logo Plate posts with the holes shown, then press them firmly into the Side Bracket. Repeat on the other side.

Final Setup and Operation

To move the desk to its final location, lift under the Side Brackets (two people recommended). Adjust the leveling glides to accommodate for uneven floors.

If your desktop includes grommet holes, insert the included Grommet Covers until they are flush with the desktop surface. If you ordered Power Grommets or Storage Grommets, follow the instructions included with those products.

Plug the Power Cord into a grounded outlet. When connected to power, the Control Box power indicator LED and Keypad displays will illuminate.

IMPORTANT: Before using your desk, perform the following Desk Reset Procedure to sync the Legs and Control Box. This procedure can be performed anytime and is particularly useful to reset any error codes.

1. Remove anything under the desk that would prevent it from moving to its lowest height.
2. Press the "down" button to lower the desk to its lowest position.
3. Press and hold the "down" button again for about 10 seconds. Keypads with a display will show "ASr". Paddle Keypads will show "RESET."
4. Press and hold the "down" button again until the desk lowers slightly, rises, and stops.
5. If the desk is working properly, you are done. If not, continue with the following steps.
6. Unplug the power cord from the electrical outlet.
7. Press and hold the "down" button for 10 seconds to discharge any stored power in the Control Box.
8. Plug the desk back in and perform this entire Desk Reset Procedure again.

Advanced Keypad Programming

For detailed Advanced Keypad Programming steps, see the QR code below or visit upliftdesk.com/uplift-desk-assembly-programming/.

Save sitting and standing heights:

1. Move the desk to the desired height.
2. Tap the "M" button followed by one of the numbered buttons.

Refer to the One-Touch, Constant-Touch, or Double-Tap section for instructions on moving the desk to a saved height.

Lock the keypad for safety and to prevent accidental adjustments:

1. Hold the "M" button until the display shows "LOC."
2. To unlock your keypad, hold the "M" button until the display shows the desk height.

If power is lost, the keypad will return to the unlocked setting.

These modes control how the desk responds to button presses:

• One-touch (default): A single touch of a numbered button automatically moves the desk to a saved height.
• Constant-touch: A numbered button must be continuously pressed to move the desk to a saved height.
• Double-tap: Two taps of a numbered button move the desk to a saved height.

To toggle between these modes:

1. Move the desk to its lowest position.
2. Press and hold the "down" button until the display shows "ASr".
3. Press and hold the number "1" button until the display shows "10.1" (one-touch), "10.2" (constant-touch), or "10.8" (double-tap). Release the button when the preferred selection is displayed.
4. When the display changes back to "ASr", press and hold the "down" button until the desk lowers and rises slightly, and the display changes back to the desk height setting.

Ensure the displayed desk height matches the actual desk height:

1. Move the desk to its lowest position.
2. Measure from the floor to the top of the desk. If the measurement does not match the display, follow the steps below.
3. Press and hold the "down" button until the display shows "ASr".
4. Press and hold the "M" button until the displayed desk height begins flashing.
5. Tap the "up" or "down" button until the displayed height matches the measured height.
6. When the display changes back to "ASr", press and hold the "down" button until the desk lowers and rises slightly, and the display changes back to the desk height setting.

Switch between inches and centimeters on your display:

1. Move the desk to its lowest position.
2. Press and hold the "down" button until the display shows "ASr".
3. Press and hold the number "2" button until the display shows "10.3" (centimeters) or "10.4" (inches). Release the button when the preferred selection is displayed.
4. When the display changes back to "ASr", press and hold the "down" button until the desk lowers and rises slightly, and the display changes back to the desk height setting.

Set the desk's minimum and maximum height limits to prevent collisions:

Set minimum desk height limit:

1. Move the desk to where you want the minimum height limit to be set.
2. Tap the "M" button once; "S-" will appear on the display.
3. Tap the "down" button; the display will flash "S-."
4. Press and hold the "M" button until the display shows "000" and changes to the desk height.

Set maximum desk height limit:

1. Move the desk to where you want the maximum height limit to be set.
2. Tap the "M" button once; "S-" will appear on the display.
3. Tap the "up" button; the display will flash "S-."
4. Press and hold the "M" button until the display shows "999" and changes to the desk height.

Remove desk height limits:

1. Tap the "M" button once; the display will show "S-."
2. Press and hold the "M" button until the display shows "555" and changes to the desk height.

Adjust the anti-collision system sensitivity:

1. Move the desk to its lowest position.
2. Press and hold the "down" button until the display shows "ASr".
3. Press and hold the "up" button until the display shows "10.5" (most sensitive), "10.6" (moderately sensitive), or "10.7" (least sensitive). Release the button when the preferred selection is displayed.
4. When the display changes back to "ASr", press and hold the "down" button until the desk lowers and rises slightly, and the display changes back to the desk height setting.

Troubleshooting

For troubleshooting steps, see the QR code below or visit upliftdesk.com/uplift-desk-reset-troubleshooting-steps/.

Error Codes: If your keypad displays any of the listed error codes, perform the Desk Reset Procedure. If the error message persists after the reset, or if there is a height difference between the Legs of more than 1.5", email support@upliftdesk.com or call 800-349-3839.

If your desk starts and stops during height adjustment, ensure the Control Box is securely attached to the frame. If the Control Box is secure and the problem persists, perform the Desk Reset Procedure.

Perform the Desk Reset Procedure any time the desk is unplugged or power has been interrupted.

Contact Information:

• UPLIFT DESK
• Work better. Live healthier.
• upliftdesk.com
• support@upliftdesk.com
• 800-349-3839
• 512-614-3152

Save This Manual: Study this manual carefully. If this product is sold, please provide this manual to the buyer, installers, or support personnel operating the product. This manual is a component of this UPLIFT Desk product and is part of the scope of delivery, even if the item is resold. This manual is also available on the UPLIFT Desk website: upliftdesk.com. This manual is subject to United States copyright law. Document AI-FV3-200-1.4.