Manuals+

UPLIFT Wall Mounted Standing Desk

Model: FRM075

The UPLIFT Wall Mounted Standing Desk can be used as a standalone desk or as a component of the OnePod Office Phone Booth, referred to as the OnePod Work Surface.

For assembly assistance, visit upliftdesk.com/contact, call 800-349-3839, or email info@upliftdesk.com.

©2022 UPLIFT Desk®. All Rights Reserved.

Requires two-person assembly.

Safety and Warnings

  • CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may result in damage or personal injury. Retain manual for future reference.
  • WARNING: Keep fingers and body parts clear of the moving desk. Check surroundings for obstacles before raising or lowering.
  • WARNING: Ensure all cords and cables have enough slack to prevent them from being pulled as the desk moves.
  • WARNING: Keep children away from the desk unless supervised. Misuse can cause personal injury. Use the safety lock feature or remove the power cord if unsupervised children are present.
  • WARNING: Designed for dry environments only. Use indoors. Outdoor or damp location use can cause electric shock, fire, or personal injury.
  • WARNING: Only plug into a properly grounded, 120V power outlet. Using a voltage converter is improper use and can cause damage.
  • WARNING: Do not open or insert objects into desk frame components like the motor housing or control box, as this may cause damage and risk electric shock.
  • WARNING: In case of spilled liquid, disconnect the desk from the power outlet immediately. Clean with a dry cloth. Wet components risk desk failure or electric shock.
  • WARNING: Never use the desk if the power cord or plug is damaged. Contact UPLIFT Desk for a replacement.
  • WARNING: Risk of serious injury or death. Adjusting height can pinch or crush body parts between the desk and stationary objects. Do not place feet or body parts on items under the desk unless they are approved foot rests or desk mats.
  • WARNING: Maintain at least a 1-inch gap between moving parts and surrounding objects to avoid pinch and crush hazards. Test full range of motion to ensure gap is maintained.
  • WARNING: Persons with limited mental or physical capabilities who cannot comprehend safe operation must not operate the desk.
  • WARNING: Inspect the desk regularly. Stop use immediately if any parts are damaged or loose. Replace only with authorized UPLIFT Desk parts and instructions.

The manufacturer does not accept warranty or liability claims for damages caused from improper use. Please provide these instructions to any new user or owner of the desk.

Package Contents

Illustration of package contents:

  • P1 Leg
  • P2 Wall Mount Bracket
  • P3 Top Mounting Plate
  • P4 Control Box
  • P5 Keypad (Note: Keypad shown may not match the keypad ordered)
  • P6 Power Cord
  • H1 M6 x 10mm Machine Screw (qty 10)
  • H2a 10mm x 65mm Lag Screw (for wall mount) (qty 3)
  • H2b M10 x 50mm Hex Head Machine Screw (for OnePod mount) (qty 3)
  • H3 10mm Plain Washer (qty 3)
  • H4 #10-24 x 3/4" Machine Screw (qty 2)
  • H5 #10 x 3/4" Wood Screw (qty 10)
  • H6 #10 Plain Washer (qty 6)
  • H7 Cable Mount (qty 3)
  • H8 4mm Allen Wrench

You'll Also Need

Illustrations of required tools:

  • Phillips Head Screwdriver
  • Stud Finder (for Wall Mount installation)
  • Level
  • Pencil (for Wall Mount installation)
  • Tape Measure (for Wall Mount installation)
  • Drill (for Wall Mount installation)
  • 1/8" Drill Bit (for Wall Mount installation)
  • 15/64" Drill Bit (for Wall Mount installation)
  • Socket Wrench
  • 17mm Socket (for Wall Mount installation)
  • 5/8" Socket (for OnePod installation)

Component Diagram

Wall Mounted Standing Desk

Diagram showing components: Desktop, Top Mounting Plate, Keypad, Control Box, Leg, Wall Mount Bracket.

OnePod Work Surface

Diagram showing components: OnePod Work Surface, Top Mounting Plate, Keypad, Control Box, Leg, Wall Mount Bracket.

Notes on Wall Construction

  • Wood Stud Installation: Use provided lag screws directly into wood studs (minimum 2" x 4").
  • Steel Stud Installation: Fasteners not included. Recommended: Toggler brand (Model 21015) or equivalent anchors for steel studs (minimum 25-gauge thickness). Follow fastener manufacturer instructions.
  • Cinder Block Wall Installation: Fasteners not included. Recommended: Toggler brand (Model 21015) or equivalent anchors for cinder block walls. Mount anchors in hollow sections, not mortar. Follow fastener manufacturer instructions. Illustration shows anchor installation in cinder block.

Assembly Instructions

Step 1 - Preparation

  • A. For ease and safety, use two people for assembly.
  • B. Assemble on a debris-free carpet or blanket to protect floors and desktop.
  • C. Ensure all components and hardware are received before disposing of packing material. Lay out items and verify quantities against the Package Contents.

Step 2 - Wall Mount Bracket for Wall Mounted Desks

If installing a OnePod Work Surface, skip to Step 3.

  • A. Determine the mounting wall and ensure a 120V outlet is nearby. Position the desk to allow safe clearance for height adjustment, avoiding obstructions like shelves or cabinets. Note: Advanced Keypads allow setting height limits to prevent collisions.
  • B. Use a stud finder to locate and mark the center of a wall stud.
  • C. Using a level, draw a vertical line on the wall centered on the stud, from the floor up to approximately 20 inches. Diagram shows wall, stud, and measurement lines.
  • D. Place the Wall Mount Bracket (P2) against the wall, aligning its three oval holes with the vertical line. Diagram shows bracket placement.
  • E. Position the bottom of the bracket about 1/2 inch above the floor or baseboard. Mark the center of each of the three mounting holes. Note: Mounting above a baseboard will raise the desk's lowest height setting.
  • F. Set the Wall Mount Bracket aside. For wooden studs, drill 2-inch deep holes at the marked locations using a 15/64" drill bit. For other wall types, refer to "Notes on Wall Construction" and follow anchor manufacturer instructions. Diagram shows drilling pilot holes.
  • G. Align the Wall Mount Bracket (P2) with the wall holes, ensuring the three bent tabs face upwards. Diagram shows bracket alignment.
  • H. For wooden studs, fasten the bracket using a 17mm socket wrench, three 10mm x 65mm Lag Screws (H2a), and three 10mm Plain Washers (H3). For other wall types, follow anchor manufacturer instructions.
  • I. Use a level to ensure the bracket is vertical before fully tightening screws.

Step 3 - Wall Mount Bracket Installation for OnePod Work Surface

If installing a Wall Mounted Desk, skip to Step 4.

  • A. Align the Wall Mount Bracket (P2) with the three holes on the right side wall of the OnePod, ensuring the bent tabs face upwards. Diagram shows bracket alignment on OnePod.
  • B. Fasten the bracket to the preinstalled threaded mount points using a 5/8" socket wrench, three M10 x 50mm Hex Head Machine Screws (H2b), and three 10mm Plain Washers (H3).
  • C. Use a level to ensure the bracket is vertical before fully tightening screws.

Step 4 - Top Mounting Plate Installation

If installing a OnePod Work Surface, skip to Step 5.

  • A. If using your own desktop, ensure it is no larger than 48" wide and 24" deep, and weighs no more than 45 lb.
  • B. Align the slotted holes in the Top Mounting Plate (P3) with the threaded metal inserts near the center of the desktop. Use inner slots for 42" wide desktops, and outer slots for 48" wide desktops or user-supplied desktops. Center the plate and align its back edge with the desktop's back edge. Diagram shows slot usage for different desktop widths.
  • C. Attach the Top Mounting Plate to the desktop threaded inserts using a Phillips Head Screwdriver, two #10-24 x 3/4" Machine Screws (H4), and two #10 Plain Washers (H6). Diagram shows attachment.
  • D. IMPORTANT: Do not drill deeper than 1/2" into the desktop surface. Wrap tape around the drill bit 1/2" from the tip as a depth guide. Stop drilling just before the tape touches the mounting plate. Diagram illustrates drill depth guide.
  • E. Drill pilot holes at the four locations along the back edge of the mounting plate using a drill and a 1/8" drill bit. If using your own desktop, drill two additional holes where circled. Diagram shows pilot hole locations.
  • F. Insert four #10 x 3/4" Wood Screws (H5) and four #10 Plain Washers (H6) into the drilled holes using a Phillips Head Screwdriver. Do not overtighten to avoid stripping. If using your own desktop, insert two additional #10 x 3/4" Wood Screws and two #10 Plain Washers into the additional holes. Diagrams show attachment to UPLIFT and customer desktops.

Step 5 - Top Mounting Plate Installation for OnePod Work Surface

If installing a Wall Mounted Desk, skip to Step 6.

  • A. Align the Top Mounting Plate (P3) on the OnePod Work Surface so the outer two slotted holes align with the threaded metal inserts. Diagram shows alignment.
  • B. Loosely insert two #10-24 x 3/4" Machine Screws (H4) and two #10 Plain Washers (H6) through the front holes of the plate into the inserts. Do not tighten yet.
  • C. Insert four #10 x 3/4" Wood Screws (H5) and four #10 Plain Washers (H6) into the four holes at the back edge of the Top Mounting Plate.
  • D. Once all six screws are started, tighten them using a Phillips Head Screwdriver. Be careful not to overtighten.

Step 6 - Leg Attachment

(for both Wall Mounted Standing Desk and the OnePod Work Surface)

  • A. Place the Leg (P1) into the Top Mounting Plate (P3) bracket. Loosely insert six M6 x 10mm Machine Screws (H1) into the holes (two on each side, two at the back). Diagram shows leg and screw placement.
  • B. Once all six screws are started, tighten them using the 4mm Allen Wrench (H8).

Step 7 - Keypad Attachment for Wall Mounted Desk

If installing a OnePod Work Surface, skip to Step 8.

  • A. Two pairs of Keypad mounting holes are pre-drilled into each side of UPLIFT 42" and 48" wide desktops.
  • B. Choose the desired side for your Keypad. Remember the desk is assembled upside down, so the Keypad placement will be on the opposite side when upright. Diagrams show Keypad on left/right side, top/bottom of desktop.
  • C. Align the Keypad (P5) with the pre-drilled desktop holes that best match the Keypad's mounting holes.
  • D. Attach the Keypad using a Phillips Head Screwdriver and two #10 x 3/4" Wood Screws (H5). Do not overtighten. Note: Keypads shown are for reference only.

Step 8 - Keypad Attachment for OnePod Work Surface

If installing a Wall Mounted Desk, skip to Step 9.

  • A. Keypad mounting holes are pre-drilled into the OnePod Work Surface near the front, left corner.
  • B. Align the Keypad (P5) with the pre-drilled holes that best match the Keypad's mounting holes. Diagram shows alignment.
  • C. Attach the Keypad using a Phillips Head Screwdriver and two #10 x 3/4" Wood Screws (H5). Do not overtighten. Note: Keypads shown are for reference only.

Step 9 - Control Box Attachment

(for both Wall Mounted Standing Desk and the OnePod Work Surface)

  • A. Position the Control Box on the Top Mounting Plate (P3), aligning its mounting holes with the two holes in the plate. Ensure the power cord port end faces the back of the desktop. Diagram shows Control Box placement.
  • B. Attach the Control Box using a Phillips Head Screwdriver and two #10 x 3/4" Wood Screws (H5). Do not overtighten. Note: For Wall Mounted Standing Desks, drill pilot holes as per Step 4 instructions.

Step 10 - Cable Connections

(for both Wall Mounted Standing Desk and the OnePod Work Surface)

  • A. Connect the Keypad cable to the port marked "HS" on the Control Box.
  • B. Connect the Leg cable to the white port marked "M1" on the Control Box.
  • C. Connect the Power Cord (P6) to the port marked "AC" on the Control Box. Diagrams show cable connections.

Step 11 - Cable Mounts

(for both Wall Mounted Standing Desk and the OnePod Work Surface)

  • Use the included Cable Mounts (H7) to bundle and organize loose cables, preventing them from snagging on objects during desk movement. Cable Mounts consist of adhesive-backed plastic anchors and reusable hook and loop strips.
  • IMPORTANT: The adhesive is very strong. Decide locations carefully before adhering. Do not attach to the top surface of your desktop or work surface.

Step 12 - Place Assembly On Wall Mount Bracket

(for both Wall Mounted Standing Desk and the OnePod Work Surface)

  • A. When flipping the assembly, be aware of loose cables to avoid tripping or damage.
  • B. With one person on each side, support the Leg (P1) and desktop equally. Slowly rotate the assembly right-side up.
  • C. While supporting the assembly, raise it and align the three bent tabs on the Wall Mount Bracket (P2) with the three rectangular openings in the back of the Leg. CAUTION: Keep hands away from the back of the Leg to avoid pinching. Diagram shows alignment.
  • D. Slowly lower the desk assembly until it is fully supported by the Wall Mount Bracket.
  • E. Loosely insert four M6 x 10mm Machine Screws (H1) through the four holes in the Wall Mount Bracket and into the Leg. Diagram shows screw placement.
  • F. Once all four screws are started, tighten them using the 4mm Allen Wrench (H8).
  • G. Check surroundings for obstacles in the desk's path during movement. Do not place objects taller than 21" underneath the desk.
  • H. Plug the desk into a grounded, 120V power outlet. Note: The OnePod provides an outlet below and to the left of the installed Work Surface.

Desk Reset Procedure

(for both Wall Mounted Standing Desk and the OnePod Work Surface)

IMPORTANT: Before use, perform the Desk Reset Procedure.

  • A. Press the down button once.
  • B. Hold the down button until the desk reaches its lowest position.
  • C. Hold the down button again for 30 seconds or until the display changes. Keypads with a display show "ASr"; Paddle Keypads show "RESET."
  • D. Hold the down button again until the desk lowers slightly, rises, and stops. If it did not move, repeat this step.
  • E. Your desk is now ready for use.
  • F. For Advanced Keypads, refer to Advanced Keypad Settings for further information. Diagrams show keypad button presses and display indicators.

Advanced Keypad Settings

These instructions apply to the following keypad types: Advanced Comfort Flush Keypad, Advanced Comfort Angled Keypad. Illustrations of keypad types.

Set & Use Memorized Heights

  • 1. Hold the up or down button to move the desk to the desired height.
  • 2. Tap the "M" button, then a number button (1, 2, 3, or 4) to assign the current height.
  • 3. Tap a numbered button to move the desk to the saved preset height.
  • Note: For button press-and-hold adjustments, see One-Touch or Constant-Touch.

Keypad Lock

  • 1. To lock: Hold the "M" button until "LOC" appears.
  • 2. To unlock: Press and hold the "M" button until the current numeric height setting appears.
  • Note: Keypad unlocks automatically after a power outage.

One-Touch or Constant-Touch

  • One-touch (default) requires a single touch to move to a saved height. Constant-touch requires holding the button/paddle.
  • Toggle between modes:
  • 1. Hold the down button until the desk reaches its lowest position.
  • 2. Hold the down button again until "ASr" flashes.
  • 3. Hold the "1" button until "10.1" (one-touch) or "10.2" (constant-touch) appears, then "ASr." While "ASr" flashes, tap "1" to toggle.
  • 4. Hold the down button until the desk moves slightly and the height setting reappears.

Units of Measurement

  • Toggle between inches and centimeters:
  • 1. Hold the down button until the desk reaches its lowest position.
  • 2. Hold the down button again until "ASr" flashes.
  • 3. Hold the "2" button until "10.3" (cm) or "10.4" (in) appears, then "ASr." While "ASr" flashes, tap "2" to toggle.
  • 4. Hold the down button until the desk moves slightly and the height setting reappears.

Calibrate Desk Height

  • Compare desk height to the displayed height.
  • 1. Press and hold the "down" button until the desk reaches its lowest position.
  • 2. Measure height from floor to desktop surface. If it matches the display, calibration is complete.
  • If height does not match:
  • 1. Hold the down button until "ASr" flashes.
  • 2. Hold the "M" button until the numeric display flashes.
  • 3. Tap up or down to adjust the displayed height to match the measured height.
  • 4. Wait for "ASr" to reappear.
  • 5. Hold the "down" button until the desk moves slightly and the height setting reappears.

Max/Min Height Limits

  • Set limits:
  • 1. Move desk to desired height.
  • 2. Tap "M" once; "S-" appears.
  • 3. Tap "up"; "S-" flashes.
    • Maximum height limit: Hold "M" until "999" appears, then the set upper limit height.
    • Minimum height limit: Hold "M" until "000" appears, then the set lower limit height.
  • Remove limits:
  • 1. Tap "M" once; "S-" appears.
  • 2. Hold "M" until "555" appears, then the current numeric height setting.

Anti-Collision System Sensitivity Adjustment

  • 1. Hold the down button until the desk reaches its lowest position.
  • 2. Hold the down button again until "ASr" flashes.
  • 3. Hold the UP button until "10.5," "10.6," or "10.7" appears (current sensitivity setting).
    • 10.5 = most sensitive (possible false positives)
    • 10.6 = moderate sensitivity
    • 10.7 = least sensitive
  • 4. While "ASr" flashes, press the up button to toggle between settings.
  • 5. Wait five seconds for "ASr" to reappear.
  • 6. Hold the down button until the desk moves slightly and the current height reappears.

Troubleshooting

Resetting the desk calibrates and syncs legs. Avoid delays waiting for replacement parts.

Reset your desk if:

  • Issues with desk operation are encountered.
  • The desk has been unplugged or lost power.

Quick Desk Reset Procedure

  1. Remove all items from under the desk. The desk will move to its lowest height.
  2. Press the down button once.
  3. Hold the down button until the desk stops at its lowest position. (Note: If the desk doesn't move, try pressing the down button for 15 seconds, then again until it reaches the lowest height.)
  4. Hold the down button again for 30 seconds or until the display changes. Keypads show "ASr"; Paddle Keypads show "RESET."
  5. Hold the down button again until the desk lowers slightly, rises, and stops. If it didn't move, try again.
  6. Try operating the desk. If it works, you are done.
  7. If the problem persists, proceed with the following steps:
  8. Unplug the power cord from the outlet.
  9. Hold the down button for 10 seconds to discharge stored power in the control box.
  10. Plug the desk back in and perform the Quick Desk Reset steps again.
  11. Try operating the desk again. If it works, the reset is complete.

For Thorough Desk Reset Instructions, see below.

Desk Error Codes - Firmware or Connectivity Issue (E01, E02, E03, E04, E05, E06)

  1. Check that all cables are securely connected to the control box and the desk has power. Verify outlet power with another device. If the outlet has no power, check your circuit breaker.
  2. Check for obstructions interfering with desk motion. Ensure nothing is too close above, below, or beside the desk.
  3. Desk moves slightly then reverses direction? This is the anti-collision safety system.
    • Ensure the control box is securely attached to the desk frame or desktop. A loose or dangling control box can falsely trigger the system.
    • Move any objects contacting the desk during movement.
    • Check for tight cords pulling on the desk. Raise the desk while watching cords; a tightening cord may trigger the system.
    • Adjust anti-collision sensitivity (see Advanced Keypad Settings).
  4. Check that all cables are installed properly and inserted firmly into the correct control box ports.

E08 Desk Error Code

  1. Follow the Thorough Desk Reset instructions to help isolate the component needing attention.
  2. Use the support form at upliftdesk.com/uplift-desk-reset-troubleshooting-steps/ for further troubleshooting. Explain the error code, any changes, and include photos of the control box and cables.
  3. If the error changes from E08 to E07, a replacement leg cable or leg may be sent.
  4. If the error remains E08, a new control box and possibly legs may be sent.

Desk Error Codes - Standing Desk Legs Are Uneven (E07, E09, E010, E011, E012)

Perform the Thorough Desk Reset procedure.

H01 Desk Error Code - Control Box Overheated

Allow the desk to cool before raising or lowering. The desk motor has a 10% duty cycle to prevent overheating (e.g., 2 minutes of use per 20-minute period). Otherwise, an H01 code may appear.

Starting & Stopping

If the desk continuously starts and stops, ensure the Control Box is securely attached to the desk frame for proper function.

Standing Desk Stability

Proper assembly is crucial for stability. If the desk feels unstable, tighten the screws fastening the desktop to the desk frame. Loose screws can cause imbalance and exacerbate instability.


File Info : application/pdf, 16 Pages, 3.07MB

PDF preview unavailable. Download the PDF instead.

FRM075-wall-mounted-standing-desk-instructions

References

Adobe PDF Library 17.0 Adobe InDesign 18.0 (Windows)

Related Documents

Preview UPLIFT V3 Standing Desk Assembly and User Manual
Comprehensive assembly instructions, safety warnings, and advanced features guide for the UPLIFT V3 Standing Desk (FV3-200 C-Frame). Learn how to assemble, operate, and troubleshoot your height-adjustable desk.
Preview UPLIFT Desk V3 Standing Desk Assembly and Operation Manual
Comprehensive guide for assembling, operating, and troubleshooting the UPLIFT Desk V3 Standing Desk (FV3-200 T-Frame), including safety warnings, parts list, assembly steps, advanced keypad programming, and error code solutions.
Preview UPLIFT V3 Standing Desk Frame Assembly Instructions (FV3-200)
A comprehensive guide for assembling the UPLIFT V3 Standing Desk frame (model FV3-200). Includes safety warnings, package contents, step-by-step assembly instructions, cable management, advanced keypad programming, and troubleshooting tips.
Preview UPLIFT Desk V2-Commercial L-Shaped Standing Desk Frame Specifications
Detailed specifications for the UPLIFT Desk V2-Commercial L-Shaped Standing Desk Frame (Model F650-F651), including warranty, dimensions, performance, and quality certifications.
Preview UPLIFT Desk V2 2-Leg Standing Desk Assembly and Operation Guide
Comprehensive guide for assembling and operating the UPLIFT Desk V2 2-Leg Standing Desk, including C-Frame and T-Frame configurations. Covers safety warnings, parts inventory, step-by-step assembly, accessory installation, desk placement, and troubleshooting.
Preview UPLIFT V3 Standing Desk Frame FV3-200 (C-frame) - Specifications
Detailed specifications for the UPLIFT V3 Standing Desk Frame (FV3-200, C-frame), including dimensions, features, warranty, and technical data. Learn about its contract-grade quality and ergonomic benefits.
Preview UPLIFT Desk Basic Display Angled Keypad Installation Guide
Comprehensive guide for installing and setting up the UPLIFT Desk Basic Display Angled Keypad (FRM072). Includes step-by-step instructions for attachment, desk reset procedures, and optional drilling guidance.
Preview UPLIFT Desk Advanced Comfort Flush Keypad FRM703 Installation Guide
Step-by-step instructions for installing and setting up the UPLIFT Desk Advanced Comfort Flush Keypad (FRM703), including desk reset procedures and optional desktop drilling.