Notice
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
Assemble on a flat, clean and soft surface. [Diagram: Two figures assembling a corner piece on a flat surface.]
Professional installation is highly recommended. [Icon: Person with hard hat and safety gear.]
Periodically Check That All Components Are Tightly Secured. [Icon: Shield with a checkmark.]
Important Safety Information
It is recommended that multiple people assemble this product. [Diagram: Two figures shown assembling a large furniture item.]
Please have the following auxiliary tools ready:
- [Screwdriver] [Image: Phillips head screwdriver]
- [Hammer] [Image: Hammer]
- [Pliers/Wire Cutters] [Image: Pliers]
- [Measuring Tape] [Image: Measuring tape]
- [Drill] [Image: Drill]
- [Wrench/Spanner] [Image: Wrench]
- [Safety Glasses] [Image: Safety glasses]
- [Hard Hat] [Image: Hard hat]
WARNING: Serious or fatal crushing injuries can occur from furniture tip-over. Always secure this furniture to the wall using tip-over restraints. [Diagram: A chest of drawers tipping forward with an arrow pointing to the wall and a bracket for securing. Another diagram shows a chest tipping backward with a red 'X' over it.]
Using Cam Lock and QuickFit
Tighten QuickFit until the shoulder is flush with the panel. Do not overtighten or undertighten. [Diagram: Close-up of a QuickFit screw being inserted and tightened until flush with the panel. Shows a checkmark (✔️) for correct and a cross (❌) for over/under-tightened.]
When fitting the cam lock, ensure the starting position is correct before inserting the connecting QuickFit. [Diagram: Shows the correct orientation of a cam lock before inserting a QuickFit, with a checkmark (✔️) and a cross (❌) for incorrect orientation.]
The QuickFit head should be in the center of the cam lock when the two panels are joined. The cam lock should be inserted before the QuickFit. Turn the cam lock clockwise to tighten. [Diagram: Shows the QuickFit head centered in the cam lock after panels are joined, and the cam lock being turned clockwise with a screwdriver to tighten.]
Parts List
| Item No. | Reference Image | Qty. |
|---|---|---|
| A | Screw M4*10 [Image: Screw] | x25 |
| B | Screwdriver [Image: Screwdriver] | x1 |
| C | Screw M6*15 [Image: Screw] | x8 |
| D | Allen Key [Image: Allen key] | x1 |
| E | Screw M4*4 [Image: Screw] | x12 |
| F | Screw M4*25 [Image: Screw] | x4 |
| Item No. | Reference Image | Qty. |
|---|---|---|
| 1 | Panel [Image: Large rectangular panel] | x1 |
| 2 | Panel [Image: Large rectangular panel] | x1 |
| 3 | Panel [Image: Rectangular panel] | x1 |
| 4 | Bracket [Image: L-shaped bracket] | x2 |
| 5 | Panel [Image: Large rectangular panel] | x1 |
| 6 | Panel [Image: Rectangular panel] | x1 |
| 7 | Support Bracket [Image: Angled support bracket] | x2 |
| 8 | Bracket [Image: Small bracket] | x1 |
| 9 | Drawer Slide Rail (Inner) [Image: Thin rail] | x1 |
| 10 | Drawer Slide Rail (Outer) [Image: Wider rail] | x1 |
| 11 | Top Panel [Image: Large flat panel] | x1 |
| 12 | Drawer Side Panel [Image: Drawer side piece] | x6 |
| 13 | Drawer Base Panel [Image: Drawer base piece] | x6 |
| 14 | Drawer Front Panel [Image: Drawer front piece] | x6 |
| 15 | Drawer Slide (Cabinet Mount) [Image: Cabinet mount drawer slide] | x6 |
| 16 | Drawer Slide (Cabinet Mount) [Image: Cabinet mount drawer slide] | x6 |
| 17 | Handle [Image: Drawer handle] | x6 |
| 18 | Rod [Image: Metal rod] | x1 |
| 19 | Bracket [Image: Metal bracket] | x1 |
Exploded View
The exploded view shows all components of the dresser laid out separately, indicating their relative positions for assembly. It illustrates how parts like side panels, back panels, drawer slides, drawer components, and the top panel fit together. Numbered labels correspond to the parts list.
Assembly Steps
Step 1
Parts: A (x2), 3 (x1), 5 (x1)
Attach panel 3 and panel 5 to panel 1 using two screws A. A close-up shows screw A being inserted into part B (likely a cam lock housing or connector) and then into panel 1.
Step 2
Parts: A (x4), 1 (x1), 3 (x1), 5 (x1)
Attach two side panels (1) to the base panel (3) and the back panel (5) using four screws A. The diagram shows the structure taking shape.
Step 3
Parts: A (x4), 2 (x1), 3 (x1)
Attach back panel 2 to the structure from Step 2 using four screws A. The diagram shows the rear of the unit being enclosed.
Step 4
Parts: A (x4), 10 (x1)
Attach the outer drawer slide rail (10) to the top edge of the side panels of the assembled unit using four screws A. Close-ups show the rail positioned and secured.
Step 5
Parts: A (x4), 9 (x1)
Attach the inner drawer slide rail (9) to the other side of the assembled unit using four screws A. This mirrors Step 4 for the opposite side.
Step 6
Parts: F (x4), 19 (x1)
Attach metal bracket 19 to the inside of the unit using four screws F. The diagram shows the bracket being affixed to a panel.
Step 7
Parts: C (x8), 4 (x2), 6 (x1), 8 (x1)
Attach two corner brackets (4) to the bottom of the unit using eight screws C. Also, attach part 6 and part 8 to the structure.
Step 8
Parts: 18 (x1), 9 (x1)
Insert rod 18 into part 9. The diagram shows the rod being slid into a component.
Step 9
Parts: 15 (x6), 16 (x6)
Assemble the drawer slides. The diagram shows two types of drawer slide components (15 and 16) being connected or prepared for attachment.
Step 10
Parts: 13 (x6)
Prepare six base panels (13). The diagram shows part 13 being folded or shaped, possibly indicating a groove or edge to be used.
Step 11
Parts: 15-1 (x6), 16-1 (x6)
Attach the cabinet-mount drawer slide components (15-1 and 16-1) to the main structure. Diagrams show precise placement on the inner sides of the unit.
Step 12
Parts: 12 (x6), 13 (x6)
Assemble six drawer boxes. This involves connecting drawer side panels (12) to drawer base panels (13).
Step 13
Parts: 14 (x6)
Attach the drawer front panels (14) to the assembled drawer boxes. Diagrams show alignment and connection points.
Step 14
Parts: E (x12), 17 (x6)
Attach the drawer handles (17) to the drawer fronts using twelve screws E. Diagrams show the handle being screwed into place from the inside of the drawer front.
Step 15
Parts: 15-2 (x6), 16-2 (x6)
Attach the drawer-mount drawer slide components (15-2 and 16-2) to the assembled drawers. Diagrams show precise placement on the sides of the drawers.
Step 16
Parts: A (x3), 11 (x1)
Attach the top panel (11) to the main structure using three screws A. Diagrams show alignment and securing the top.
Step 17
Parts: (Implied: Assembled drawers)
Insert the assembled drawers into the main unit. Arrows indicate the direction of insertion.
Step 18
Parts: A (x4), 7 (x2)
Attach two support brackets (7) to the bottom of the unit using four screws A. Diagrams show the brackets being affixed to the base for stability.
Help Center
[Icon: Speech bubble with question mark] Inquiry
[Icon: Person with wrench] Assembly issue
[Icon: Box with 'X'] Missing parts
If you encounter any difficulties during assembly, please contact us.
Disclaimer
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.
