Wardrobe Assembly Instructions

Step 1

Parts used: A x 8, E x 6, I x 2, O x 1

Insert the eccentric rod A into board 7 and 8. Use screw E to fix the stopper I onto boards 7 and 8.

[Diagram: Shows eccentric rod A inserted into holes on boards 7 and 8, and screw E securing stopper I to these boards.]

Step 2

Parts used: B x 4

Connect board 7 with two board 3, and rotate the eccentric wheel B clockwise to lock (180° turn).

[Diagram: Shows board 7 being attached to two boards 3 using eccentric wheels B, with a close-up showing the 180° locking mechanism.]

Step 3

Insert board 18.

[Diagram: Shows board 18 being slid into place between boards 7 and 3.]

Step 4

Parts used: B x 4

Connect board 8 with two board 3, and rotate the eccentric wheel B clockwise to lock (180° turn).

[Diagram: Shows board 8 being attached to two boards 3 using eccentric wheels B, similar to Step 2.]

Step 5

Parts used: C x 4, D x 4

First insert the back board 18. Insert wooden dowel C into board 7 and 8. Connect board 2 with board 7 and 8, and use screw D to lock.

[Diagram: Shows dowels C inserted into boards 7 and 8, then board 2 attached using screws D.]

Step 6

Insert the back board 18.

[Diagram: Shows board 18 being inserted into the partially assembled structure.]

Step 7

Parts used: C x 4, D x 4

Insert wooden dowel C into board 7 and 8. Connect board 1 with board 7 and 8, and use screw D to lock.

[Diagram: Shows dowels C inserted into boards 7 and 8, then board 1 attached using screws D.]

Step 8

Parts used: A x 4

Insert the eccentric rod A into board 2.

[Diagram: Shows eccentric rods A being inserted into board 2.]

Step 9

Parts used: E x 12, CL x 2, CR x 2

Use screw E to fix guide rails CL onto board 9. Use screw E to fix guide rails CR onto board 10.

[Diagram: Shows guide rails CL attached to board 9 and guide rails CR attached to board 10 using screws E.]

Step 10

Parts used: A x 16, K x 4

Insert the eccentric rod A into board 9 and 10. Knock in foot pad K onto board 9 and 10.

[Diagram: Shows eccentric rods A inserted into boards 9 and 10, and foot pads K being hammered into the bottom of these boards.]

Step 11

Parts used: B x 8, C x 2

Insert wooden dowel C into board 9. Connect board 9 with board 3, 4, 5, 6, and 20. Rotate the eccentric wheel B clockwise to lock (180° turn).

[Diagram: Shows dowels C inserted into board 9, then board 9 connected to multiple other boards (3, 4, 5, 6, 20) using eccentric wheels B.]

Step 12

Insert back board 19.

[Diagram: Shows board 19 being inserted into the structure assembled in Step 11.]

Step 13

Parts used: B x 8, C x 2

Insert wooden dowel C into board 10. Connect board 10 with board 3, 4, 5, 6, and 20. Rotate the eccentric wheel B clockwise to lock (180° turn).

[Diagram: Similar to Step 11, but for board 10.]

Step 14

Insert back board 19.

[Diagram: Shows board 19 being inserted into the structure assembled in Step 13.]

Step 15

Parts used: B x 4, C x 6

Insert wooden dowel C into board 9 and 10. Connect board 2 with board 9 and 10. Rotate the eccentric wheel B clockwise to lock (180° turn).

[Diagram: Shows dowels C inserted into boards 9 and 10, then board 2 attached to them using eccentric wheels B.]

Step 16

Parts used: G x 20, E x 20

First insert fastener G onto the back board. Then use screw E to lock.

[Diagram: Shows fasteners G being inserted into the back panel (likely board 19) and secured with screws E.]

Step 17

Parts used: E x 4, N x 2, J x 1

Use screw E to fix anti-tip piece N onto board 1. Insert the hanger rod J.

[Diagram: Shows anti-tip pieces N attached to the top of the unit (board 1) with screws E, and hanger rod J being inserted.]

Step 18

Parts used: D x 10

Use screw D to connect board 14 with boards 12, 13, and 15. (This step is repeated x2, implying two identical sub-assemblies).

[Diagram: Shows boards 12, 13, 14, and 15 being joined to form two identical drawer/base units using screws D.]

Step 19

Parts used: A x 10

Insert board 17. Insert the eccentric rod A into board 16. (This step is repeated x2).

[Diagram: Shows board 17 inserted into the assemblies from Step 18, and eccentric rods A inserted into board 16.]

Step 20

Parts used: B x 10

Connect board 16 with boards 12 and 13. Rotate the eccentric wheel B clockwise to lock (180° turn). (Repeated x2).

[Diagram: Shows board 16 being attached to the assemblies from Step 19 using eccentric wheels B.]

Step 21

Parts used: E x 12, DL x 2, DR x 2

Use screw E to fix guide rail DL onto board 12. Use screw E to fix guide rail DR onto board 13. (Repeated x2).

[Diagram: Shows guide rails DL attached to board 12 and guide rails DR attached to board 13 using screws E.]

Step 22

Insert the drawers into the cabinet.

[Diagram: Shows completed drawer units being slid into the main cabinet structure.]

Step 23

Parts used: E x 12, F x 6

Use screw E to fix hinge F onto two board 11.

[Diagram: Shows hinges F being attached to the doors (board 11) using screws E.]

Step 24

Parts used: E x 24

Use screw E to connect board 11 (doors) with board 7 and 8 (cabinet sides) via hinge F.

[Diagram: Shows the doors (board 11) being attached to the cabinet sides (boards 7 and 8) using the previously attached hinges.]

Step 25

Door adjustment instructions.

[Diagram: Series of diagrams showing how to adjust the hinges for proper door alignment using adjustment screws.]

Step 26

Parts used: L x 2, M x 2, N x 2

Mark the wall, drill holes, insert plastic piece M, and use screw L to fix plastic piece M via anti-tip piece N.

[Diagram: Shows marking the wall, drilling holes, inserting wall anchors (M), and securing the unit to the wall using screws (L) and anti-tip pieces (N).]