🐶 Mcombo
Mcombo Recliner TV Chair
Model: 6151-4687
NOTE: Please read carefully before use and keep for future reference.
Congratulations!
Mcombo Recliner TV Chair - a name synonymous with classic design and the carrier of value and quality. Our products are directly from factory and eliminated the cost of middlemen. The Recliner TV Chair is a high-quality seating solution to enhance comfortable feelings as you try to enjoy your leisure time.
Warranty
All warranties are to the original purchaser from MCOMBO ONLY®.
- MCOMBO® will replace the defective parts or send replacement item provided that the warranty parts have not been subjected to misuse, abuse or improper service by the consumer, for example, damaged wire arising in consequence of negligence or improper operation.
- MCOMBO® All of recliners come with a 30-day return/replace policy. During this time, we will cover the shipping cost of return and replacement for defective and damaged items, through provide pre-paid return label or pick up service for customer's convenience.
Parts List
- Part A: 10x Bolt M8 x 38
- Part B: 10x Flat Washer Ø8*22*2
- Part C: 2x Bolt M6 x 20
- Part D: 2x Bolt M5 x 10
- Part E: 4x Bolt M6 x 25
- Part F: 2x Bolt M8 x 70
- Part G: 2x Bolt M8 x 25
- Part H: 2x Bolt M8
- Part I: 1x Allen Wrench M6
- Part J: 1x Allen Wrench M8
- Part K: 1x Right Armrest
- Part L: 1x Left Armrest
- Part M: 1x Ottoman Leg Support
- Part N: 1x Ottoman Round Base
- Part O: 1x Ottoman Cushion
- Part P: 2x Ottoman Bracket
- Part Q: 2x Seat Leg Support
- Part R: 1x Seat Round Base
- Part S: 1x Seat Cushion
- Part T: 1x Back Cushion
- Part U: 1x Wrench
- Part V: 2x Washer
- Part W: 1x Lumbar Pillow
- Part X: 1x Remote Control
- Part Y: 1x Adapter
Assembly Instructions
Step 1
Diagram shows the ottoman base (N). Two ottoman leg supports (M) are attached to the base using bolts (A & B) and tightened with Allen wrench (I). An ottoman bracket (P) is installed on each leg support (M). Finally, the ottoman cushion (O) is secured to the base using bolts (C).
Step 2
Diagram illustrates the seat base (R). Two seat leg supports (Q) are attached to the seat base (R) using bolts (A & B) and tightened with Allen wrench (I). The diagram shows the bolts passing through pre-drilled holes.
Step 3
Diagram shows the seat cushion (S) being placed onto the chair frame. Adjusting levers on the sides of the seat cushion are aligned with corresponding holes on the armrest frame. A tip suggests inverting the chair frame and base, then inverting the seat cushion for easier installation.
Step 4
Diagram shows the armrest assembly. A washer (V) is inserted between the adjusting lever and the armrest rod. A screw (D) is used to fix the armrest frame and the adjusting lever, tightened with wrench (I).
Step 5
Diagram shows the back of the backrest being aligned with the seat cushion. Small iron plates on the backrest are used to fix the back cushion. Screws (G & H) are used for this attachment, tightened with wrenches (I & U).
Step 6
Diagram shows the back cushion (T) being placed onto the seat cushion. Screw holes on the armrest frame are aligned with screw holes on the side of the back cushion. Screws (F) are used to secure the back cushion, tightened with wrench (J).
Step 7
Diagram shows the left armrest (L) and right armrest (K) being attached to the armrest frame. Screws (E) are used for this attachment, tightened with wrench (I).
Step 8
Diagram shows three wire connections. The adapter (Y) connects to a small black connector on the chair. The remote control (X) connects to two large black connectors. The vibrating power cord connects to two small white connectors.
