Scosche GM1515F: Vehicle Dash Installation Kit

Introduction

Thank you for choosing the Scosche GM1515F kit. This installation kit is manufactured to the highest quality standards. Designed to replace the factory-installed dashboard radio, this kit allows for the installation of a single-DIN or shaft-mount stereo, or other aftermarket accessories. The kit features a 1/2 inch molded extension to accommodate stereos with deeper chassis. Its mounting design is identical to the factory radio, eliminating modifications. It is molded in the same gray color and texture as factory dashboards for an OEM appearance.

Preliminary Steps / Radio Removal

WARNING: Before proceeding with installation, disconnect the negative battery cable of the vehicle to prevent damage to the electrical system.

Radio Removal

Consult your specific vehicle's disassembly/installation instructions (refer to the Table of Contents) for complete information on removing the factory radio.

Stereo Installation

Factory Stereo Removal

1. Remove the (3) screws securing the under-dash trim panel on the driver's side.
2. Remove the (3) screws securing the center under-dash trim panel.
3. Remove the (2) screws securing the center panel below the dashboard leading to the heater outlet, then remove the panel.
4. Pull out the ashtray to remove it from the dashboard.
5. Remove the (8) screws securing the panel below the steering column to the dashboard, disconnect all connectors, and remove the panel.
6. Remove the (2) screws located at the upper edge of the instrument cluster that secure the radio trim bezel to the dashboard.
7. Apply the parking brake and place the steering column gear shift lever (if equipped) in low gear.
8. Using the provided panel removal tool, lift the radio trim bezel, release the retaining clips securing the bezel to the dashboard, disconnect connectors, and remove the bezel.
9. Remove the (4) screws securing the heater control panel to the dashboard and remove the panel from the dashboard cavity.
10. Remove the (4) screws securing the radio and dashboard pocket to the dashboard, slide the radio out of the dashboard, disconnect all connectors, and remove the radio.
11. Loosen the (2) 10mm nuts located on the other side of the radio, as well as the nut on the rear of the radio that secures the pocket to the radio. Remove the pocket.

GM1515F Kit Preparation

1. Using the provided 10mm mounting hardware, attach the pocket to the side surface of the kit in the same manner it was attached to the factory radio. (See Illustration A).

Assembly for Radio

This section describes the assembly of the kit components for radio installation.

Illustration A Description: The illustration shows the components for mounting a car stereo. Key parts include: a 'Radio DIN' unit, a 'Mounting Sleeve' (Manchon de Montage de la Radio), 'Rear Support Brackets' (Courroies Arrière de Soutien), a 'Factory Pocket' (Pochette de l'Usine), and a 'Mounting Panel' (Panneau de Montage). The process involves fitting the radio into the mounting sleeve, attaching the sleeve to the mounting panel, and potentially using the rear support brackets and the factory pocket.

Stereo Installation (Continued)

1. Connect the stereo to the factory wiring harnesses (refer to wire codes) as described in the stereo installation guide. (Using the Scosche GMDA original connector and the Scosche MDA-1 antenna adapter eliminates the need to cut factory plugs.)

Vehicle Applications

Applications De Véhicules:

• Chevrolet: 1995-97 S-10 Blazer 2 DR/4DR, 1994-97 S-10 Pickup
• Isuzu: 1996-97 Hombre Pickup
• GMC: 1995-97 Jimmy Blazer, 1994-97 Sonoma
• Oldsmobile: 1996-97 Bravada Blazer

Car Stereo Connectors

GMDA: Provides easy connection of your car stereo to factory wiring harness. Compatible with 1988-up General Motors Vehicles.

Illustration A (continued): Shows the car stereo connectors, specifically the GMDA connector, designed for easy integration with factory wiring.

Disclaimer

This instruction guide is based on carefully documented data and research on automotive dashboard disassembly, wiring harnesses/codes, and installation information for this kit (GM1515F) in 1994 and newer GM vehicles. Scosche Industries, Inc. cannot be held responsible for any discrepancies or inconsistencies that may arise due to modifications or options in automotive construction, nor for any damage that may occur to the automobile during the installation of components following the guidelines in this booklet.

Technical Support

If you have questions, please call Scosche Industries, Inc.

Technical Support: 1-800-621-3695 ext. 3

Document Version: SI 2/05-GM1515F (3000162)