GOTRAX GXL V2 E-SCOOTER

Congratulations on Your Purchase!

This user manual will help you assemble and operate your new electric scooter. Be sure to read ALL OF THE INFORMATION in this manual before riding.

NOTE TO ALL RIDERS UNDER 18 YEARS OF AGE: It's very important that you get parental permission before riding your electric scooter.

DON'T RIDE UNTIL YOU READ THIS:

• ⛑️ ALWAYS wear a helmet when riding your electric scooter.
• ? Make sure your scooter has a full battery before taking it out to ride.
• ⚠️ Always be aware of local road laws, and follow them.
• ? Do not ride the scooter under the influence of drugs or alcohol.
• ? Always respect pedestrians.
• ?️ Do not ride under wet conditions. The scooter may slide from under your feet causing injury. Wet conditions may damage the electronics and void the warranty.

WARNING MESSAGE

1. ? Avoid water - The scooter is not waterproof. The electronics may be damaged due to water and water damage is not covered by our warranty. Riding in wet conditions is also very dangerous and may result in injury.
2. ⚠️ Abuse - We do not cover physical damage due to negligent care and extreme riding.
3. ⚠️ Risk of Injury - Whenever you ride the Gotrax Electric Scooter, you risk severe injury or even death from loss of control, collisions, and falls. Use caution and ride at your own risk.
4. ? Modification - Do not modify the product from the manufacturer's original design; this will void the warranty.
5. ⚙️ Moving Parts - Keep hands and all body parts away from moving parts while operating the scooter.
6. ✔️ Pre-Ride Check - Before riding, be sure to check the scooter over and make sure the scooter is operating correctly before each use.
7. ? Braking System - Before riding, be sure to check that the braking system is functioning properly; also be sure to check that all safety labels are in place and you understand the safety warnings.
8. ?️ Guards - Before riding, be sure that any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable condition.
9. ⚙️ Tires - Before riding, be sure to check that the tires are in good condition, inflated properly, and have sufficient tread remaining.
10. ⚖️ Load Rating - Never exceed the 220 lb (100 kg) maximum load rating.
11. ? Age Limit - The electric scooter should never be used by children under the age of 13.
12. ? Maximum Speed - Your electric scooter goes the maximum speed of 15.5 mph.

UNPACK

You should find each of these items in your box:

1. Electric Scooter
2. Console & Handlebars
3. Approved Power Adapter / Charging Unit
4. Allen Wrench
5. Tire Pump Extender
6. Safety Pin

Diagram Description: The diagram shows the electric scooter laid out with numbered callouts pointing to the main scooter body (1), the console and handlebars (2), the charging unit (3), an Allen wrench (4), a tire pump extender (5), and a safety pin (6). The text below instructs to remove all packaging material and inspect items for shipping damage.

GET TO KNOW YOUR SCOOTER

The electric scooter comes partially assembled.

Diagram Description: A line drawing of the electric scooter with labels pointing to its various parts:

• Headlight: Located at the front of the handlebars.
• Handbrake: Lever on the left handlebar.
• Tiller: The vertical steering column.
• Accelerator (right thumb throttle): Lever on the right handlebar.
• Console: Display unit on the handlebars.
• Charger Port: Located on the tiller, usually covered by a rubber flap.
• Hook: A folding mechanism component, typically on the tiller.
• Hub Motor: Located within the wheel hub, likely the rear wheel.
• Kickstand: Foldable support to keep the scooter upright when not in use.
• Folding Mechanism: The joint that allows the scooter to fold.
• Fender Buckle: A component on the rear fender used for securing the folded scooter.
• Disc Brake: Located on the rear wheel.

ASSEMBLING YOUR SCOOTER

TOOLS YOU'LL NEED: 4 mm Allen Key Wrench (both included).

1. Step 1: Unfold the scooter by pressing down on the rear fender. Separate the folding hook and fender buckle, then lift the tiller upright.

   Diagram Description: Shows the rear fender being pressed down, releasing a hook and buckle, and the tiller being lifted.

2. Step 2: Use the Allen wrench to loosen the screws located at the hook and detach. Once you've removed the hook and screws, make sure to remove the plug inside of the top of the tiller.

   Diagram Description: Shows an Allen wrench turning screws on the folding hook mechanism. An arrow indicates removing a plug from the tiller.

3. Step 3: The brake line will be put into the crevasse on the bottom of the brake piece on the handle bar.

   Diagram Description: Close-up of the handlebar area showing a brake line being guided into a groove on the brake lever assembly.

4. Step 4: Press down brake lever to be able to insert the pin on the brake line.

   Diagram Description: Shows a hand pressing the brake lever, creating an opening to insert a pin.

5. Step 5: Lower brake line pin into hole in the brake lever.

   Diagram Description: Shows the brake line pin being inserted into a hole on the brake lever.

6. Step 6: Pull brake cable into the crevasse to the left.

   Diagram Description: Shows a brake cable being pulled into a channel or groove.

7. Step 7: Line up brake line into the (Red) Hook attachment.

   Diagram Description: Shows the brake line being aligned with a red-colored hook component.

8. Step 8: Attach the Console to the Tiller. (Line up the pins in the console to the pins on the battery.)

   Diagram Description: Shows the console unit being attached to the tiller, aligning pins.

9. Step 9: Tighten the (2) screws provided.

   Diagram Description: Shows an Allen wrench tightening screws on the console attachment.

10. Step 10: Secure the screws. Be sure to check the scooter after assembly to make sure that the scooter is operating correctly.

    Diagram Description: Shows a close-up of secured screws, implying the final assembly step.

CHARGE YOUR SCOOTER

Before using the scooter, you must fully charge the battery.

Diagram Description: A line drawing of the electric scooter connected to its charger. The charging cable runs from the charger unit (plugged into a wall outlet) to the charging port on the scooter's tiller. An arrow points to the charging port.

1. Open the rubber charging port cover.
2. Insert the charging plug into the port.
3. The charger box will have a green light ? when fully charged and a red light ? when charging.
4. When you are done charging, be sure to cover the charging port to keep it clear of dust and debris.

SCOOTER CONSOLE FUNCTIONS

• To power the scooter on, press and hold the red button ? for 1 second.
• To power the scooter off, press and hold the red button ? for 5 seconds.
• To power the headlight on or off, press the red button ? for 1 second while the scooter is powered on.
• To change between 1st and 2nd gear, press the red button ? for 2 seconds. The display screen on the console will switch from the number 1 for 1st gear and number 2 for the 2nd gear.

The console on the Scooter displays speed in MPH, Battery life, and what gear the scooter is currently in.

Diagram Description: Two diagrams are shown. Diagram 1 shows a close-up of the scooter's console display, illustrating indicators for speed (e.g., "88"), battery life (a battery icon), and gear (e.g., "1" or "2"). Diagram 2 shows a finger pressing the red button on the console.

RIDING TIPS

1. You will want to start riding your electric scooter with one foot on the platform and one foot on the ground. Use your foot on the ground to push off and at the same time, press the throttle button to begin movement.
2. Press the handbrake to slow down or stop.
3. The scooter performs best when on a smooth surface, e.g., carparks, smooth roads, footpaths, & bike lanes.
4. Always clean your scooter (wheels, platform, etc.); it's a machine and it needs to be maintained. See maintenance page.
5. Do not press the throttle while walking with the scooter beside you.
6. Be aware of the terrain you are riding on; watch out for curbs and obstacles!
7. Use the red button ? to change between gears as you would on a bike, cycle through them according to the terrain and elevation. First gear equals more torque for going uphill, Second gear is more speed for straight aways.
8. Cruise Control: To activate the cruise control, press the right-hand throttle down for 10 seconds. To deactivate the cruise control, press either the right-hand throttle or handbrake to deactivate the cruise control.

PUTTING YOUR SCOOTER AWAY/FOLDING

Before folding the scooter, make sure that the scooter is powered off and remove the safety pin.

Pull the Tiller towards the back wheel. Insert the hook on the tiller into the loop on the rear fender buckle. You may hear a click which indicates that you were successful in folding and locking the scooter.

Diagram Description: Three diagrams illustrate the folding process:

• Diagram 1: Shows the folding mechanism at the base of the tiller being manipulated, likely releasing a latch.
• Diagram 2: Shows a hand pulling the tiller downwards and towards the rear wheel.
• Diagram 3: Shows the scooter in its folded state, with the tiller hooked onto the rear fender.

MAINTENANCE & REPAIR

If you regularly clean and maintain your electric scooter, it will extend its life.

• Cleaning and storage: If the scooter is dirty, wipe it clean with a soft damp cloth.
• Brake Adjustments & Service: If you notice you need brake adjustments or any service on your scooter, contact our customer service team and we will adjust and repair your scooter. Do not repair your scooter yourself, this can void your warranty and you risk damaging the scooter.
• Tires: If you notice that the tire pressure is low, please fill to the recommended PSI on the side of the tire. Recommended PSI: 50 ?
• Cleaning Agents: DO NOT use alcohol, gasoline, kerosene, or other corrosive chemical solvents to clean the scooter. It can severely damage the appearance and structure of the scooter. Please do not use a pressure washer as it may also cause damage to the electronics.
• Storage: When you're not using your scooter, store it in a dry and cool location. Avoid storing your scooter outdoors because sun exposure can damage its appearance and may cause wear on the life of the battery and tires.
• Tightening the Tiller: If you notice that the tiller is loose or wiggles while riding, you can tighten the screws. Open the plastic cover, and use the Allen wrench ? to tighten the screws.

SECURING THE SAFETY PIN

The Safety Pin secures the scooter in the riding position.

Diagram Description: Four diagrams illustrate securing the safety pin:

• Diagram 1: Shows the location of a hole near a red lever on the bottom of the scooter.
• Diagram 2: An arrow points to the safety pin itself.
• Diagram 3: The safety pin is shown being inserted into the hole.
• Diagram 4: The safety pin is twisted to secure it firmly in place.

BATTERY INFORMATION

Only use the approved Gotrax power adapter ? to charge your scooter; others may cause risk of fire ? & equipment damage.

Improper disposal of used batteries may seriously pollute the environment. Please comply with local disposal regulations.

Make sure to store your scooter and power adapter in conditions that do not exceed 122 degrees Fahrenheit or below -4 degrees Fahrenheit.

Warning - Risk of Fire - No User Serviceable Parts. Prolonged exposure to UV Rays, Rain, and the Elements may damage the enclosed materials; store indoors when not in use.

TROUBLESHOOTING

We frequently update our user manuals at gotrax.com, and reserve the rights to update and change manuals online.

Please contact our customer service team if you are experiencing problems or need more detailed information. They can be reached at gotrax.com.

WARRANTY

This scooter is covered by a 90-day manufacturer's warranty that covers defects in workmanship and material. This does not cover misuse, neglect, abuse, accident, or water damage. For warranty claims and details, please visit gotrax.com. Always keep your original shipping box in case the scooter needs to be returned or repaired.