NuPhy HALO96 V2 Quick Guide

Brand: NuPhy

01. System Selection

OS Selection

Win Mode: For Windows operating systems.

Mac Mode: For macOS operating systems.

02. Connection Mode Selection

Device Connection Guide

Power Off: Turn off the device.

Wired Mode: Use a data cable to connect with the device. In wired mode, a data cable is necessary to connect with the device.

Wireless Mode: For wireless connection.

03. Wireless Device Connection

Bluetooth Pairing Guide

Pairing: Long press for 3 seconds to enter pairing mode. Short press to switch between devices.

2.4Ghz Connection: Plug the included 2.4Ghz receiver into your computer before pressing FN + 4.

Key Combinations:

FN + 1: Bluetooth 1
FN + 2: Bluetooth 2
FN + 3: Bluetooth 3
FN + 4: 2.4Ghz

04. Backlight Settings

Keyboard Backlight Guide

Controls:

FN + Backlight effect switching: Cycle through backlight effect modes.
FN + >: Cycle through backlight colors.
FN + Brightness +/-: Adjust backlight brightness.
FN + : Adjust backlight speed (increase/decrease).

05. Auxiliary Lights Settings

Auxiliary Light Guide

Controls:

FN + M + < : Cycle through auxiliary light effect modes.
FN + M + > : Cycle through auxiliary light colors.
FN + M + Brightness +/- : Adjust auxiliary light brightness.
FN + M + : Adjust auxiliary light speed (decrease/increase).
FN + M + ? : Cycle through auxiliary light group presets.

06. Sleep Mode Setting

Sleep Mode Configuration

Control: FN + ) : Turn sleep mode on or off.

Description: If the keyboard is not operated for 6 minutes, it will turn off the lights and enter sleep mode to save battery. It is recommended to enable sleep mode for longer battery life.

07. Battery Indicator

Battery Check Guide

The RGB Light Bar displays status indicators. These include battery levels (81%-100%, 51%-80%, 21%-50%, 0%-20%), connection modes (Wired, Mac, Bluetooth, 2.4G), and Caps Lock status.

Function: FN + 1 : Enable or disable permanent battery level display.

08. Factory Reset

Restore Factory Settings

Procedure: Press and hold FN for 3 seconds to restore factory settings.

09. Screenshot Shortcut

Capture Screen

Mac:

FN + (mac) : Section screenshot (select an area).
FN + (mac) : Full screen screenshot.

Windows:

(win) : Open Snipping Tool and take a screenshot.
FN + (win) : Keyboard shortcut for print screen.

10. VIA Keymap Configurator

VIA Mapping Software

This keyboard is compatible with VIA, a third-party open-source software used to configure keymaps, light effects, and macros.

Download Latest Version: Visit nuphy.com/pages/console.

Troubleshooting: If VIA fails to detect your keyboard in wired mode, contact NuPhy for technical support.

Note: Mac Mode uses LAYER 0/1; Win Mode uses LAYER 2/3.

Regulatory Information

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

IC Warning

This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.