Frisco 72" Cat Tree Instruction Manual
Brand: Frisco
Height: 72 inches
SKU#: 101811, 101813
Overall Dimensions: 72"H x 39"W x 27"L
Baseboard Dimensions: 23.5"W x 21.5"L
Warnings & Cautions
Please read and follow all warnings and instructions to avoid pet injury or property damages.
- Keep all tools and instructions in a safe place for future reference.
- Follow the instructions carefully and make sure you've completed each step.
- This cat tree is intended for cat use only; please keep children away.
- Keep all small parts away from children/pets to avoid choking hazards.
- Never climb, rock, shake, step, or hang on the cat tree.
- Place your cat tree indoors, away from direct sunlight or damp areas.
- Cat trees should be placed on a flat, level surface for stability.
- Check your cat tree often for loose screws or parts that might need re-tightening.
- If your cat tree gets torn or damaged, please discard it.
- The product photo may vary slightly from your fully assembled cat tree as this product is continually being enhanced.
Cleaning Instructions
Spot clean stains and vacuum fur (using small handheld or attachment) when necessary.
Components
Prior to assembly, be sure to identify and sort all components shown below.
- 1: 1PC Baseboard
- 2: 1PC Platform
- 3: 1PC Apartment
- 4: 1PC Platform
- 5: 1PC Apartment
- 6: 1PC Perch
- 7: 1PC Perch
- 8: 1PC Perch
- 9: 1PC Scratching Board
- 10: 1PC Scratching Board
- 11: 4PCS Scratching Post 520mm
- 12: 3PCS Scratching Post 380mm
- 13: 2PCS Scratching Post 430mm
- 14: 1PC Scratching Post 445mm
- 15: 1PC Rope
Hardware:
- A: 46mm Bolt (8PCS)
- B: 60mm Bolt (1PC)
- C: 90mm Double-sided Bolt (4PCS)
- D: Bracket (3PCS)
- E: 16mm Bolt (9PCS)
- F: Bracket (1PC)
- G: Bracket (1PC)
- H: 30mm Screw (1PC)
- I: 18mm Washer (1PC)
- J: 30mm Drywall Anchor (1PC)
- K: 31mm Bolt (1PC)
- L: 5mm Wrench (1PC)
- M: 4mm Wrench (1PC)
Assembly Instructions
Step 1
Attach component 3 to component 1 using hardware A, D, and E.
Attach component 10 to component 3 using hardware A and E.
Step 2
Attach components 11 and 12 to component 2 using hardware A.
Attach component 5 to component 4 using hardware A.
Attach component 11 to component 5 using hardware A.
Step 3
Attach component 15 (Rope) to component 5 using hardware C.
Attach component 2 to component 1.
Step 4
Attach component 4 to component 2 using hardware C.
Attach component 12 to component 4 using hardware A.
Attach component 11 to component 4 using hardware A.
Attach component 9 to component 5 using hardware C.
Note for easier assembly: Loosely attach brackets (D, F, G) to the scratching board (9) by inserting screws (H) without completely tightening. Then, align the scratching board with the apartment (5) and platform (4) and secure it by tightening the screws.
Step 5
Attach component 14 to component 8 using hardware A.
Attach component 7 to component 13 using hardware A.
Attach component 6 to component 13 using hardware A.
Attach component 13 to component 2 using hardware A.
Attach component 13 to component 1 using hardware A.
Optional Wall Mounting Kit: Use components G, H, I, and J to secure the cat tree to the wall for added stability. Follow the instructions provided with the wall mounting kit.
Finished Assembly
Your Frisco 72" Cat Tree is now assembled. Ensure all parts are securely tightened before allowing pets to use the product.
