NYSJÖN Laundry Cabinet
Assembly Instructions
⚠️ WARNING!
Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over this furniture must be used with the wall attachment device(s) provided.
Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.
Hebrew: אזהרה! נפילת הרהיט עלולה לגרום לפגיעה גופנית חמורה או קטלנית. על מנת למנוע את נפילת הרהיט, יש לקבע אותו לקיר באמצעות אבזרי הקיבוע הכלולים באריזה. הברגים לקיבוע אינם כלולים מכיוון שיש להתאים אותם לחומר ממנו עשוי הקיר המיועד. לקבלת מידע נוסף על הברגים המתאימים לקיבוע, אנא פנו לאיש מקצוע. קראו ופעלו לפי ההוראות המפורטות בזהירות.
Parts List
- 16x Dowel (Part ID: 123492)
- 16x Dowel (Part ID: 101375)
- 1x Screw (Part ID: 119976)
- 6x Screw (Part ID: 124431)
- 16x Cam Lock (Part ID: 102509)
- 8x Screw (Part ID: 10048881)
- 4x Bracket (Part ID: 10043569)
- 4x Mounting Plate (Part ID: 10032274)
- 4x Hinge Plate (Part ID: 153647)
- 2x Foot (Part ID: 123029)
- 1x Support (Part ID: 105494)
- 1x Support (Part ID: 106266)
- 1x Cover (Part ID: 107091)
- 2x Bracket (Part ID: 10068747)
- 2x Mounting Bracket (Part ID: 10059781)
- 2x Foot Housing (Part ID: 10056734)
- 1x Screw (Part ID: 101221)
- 3x Hinge (Part ID: 144553)
- 2x Ring (Part ID: 122584)
- 2x Ring (Part ID: 122619)
- 3x Door Stop (Part ID: 139244)
Tools Required (Not Included)
- Screwdrivers (Phillips and flathead)
- Hammer
- Measuring tape
- Pencil
- Drill
- Clamp (optional, shown in diagrams)
Note: Specific screws and wall plugs for your wall type are not included.
Assembly Steps
Step 1
Attach mounting plates (Part ID: 10032274) to the base panel using screws (Part ID: 10048881). Ensure correct orientation as shown in the magnified view.
Visual: Two side panels are shown. A mounting plate is positioned on each, and screws are inserted through the plate into pre-drilled holes. A magnified view shows the plate and screws.
Step 2
Insert dowels (Part ID: 123492) into the designated holes on the side panels. A total of 16 dowels are used.
Visual: A panel is shown with dowels being inserted into holes. A magnified view shows a dowel being pushed into a hole.
Step 3
Attach the horizontal shelf panels to the side panels using the inserted dowels. Four shelf panels are used, each secured with 4 dowels (Part ID: 101375).
Visual: Four horizontal panels are shown being aligned with the dowels on the side panels. A magnified view shows dowels being inserted into the edge of a horizontal panel.
Step 4
Assemble the main frame by connecting the side panels and horizontal shelves. Ensure the panels are correctly oriented, with the correct edges facing outwards.
Visual: The partially assembled frame is shown, with arrows indicating the direction of assembly for the vertical and horizontal pieces.
Step 5
Insert cam lock housings (Part ID: 102509) into the large holes on the horizontal panels. A total of 8 cam lock housings are used. Turn them to prepare for locking.
Visual: Cam lock housings are shown being inserted into holes. A magnified view shows the cam lock housing and the arrow indicating the direction to turn it.
Step 6
Secure the structure by turning the cam locks (Part ID: 102509) to engage with the connecting screws/dowels. This locks the horizontal panels to the side panels.
Visual: The cam locks are shown being turned with a screwdriver to secure the structure.
Step 7
Attach the back panels. The diagram shows the unit upside down, with the back panel being placed and secured.
Visual: The cabinet frame is shown upside down. A back panel is being positioned.
Step 8
Flip the unit upright and attach the top panel. The top panel is secured using cam locks.
Visual: The cabinet is shown upright. A top panel is being placed on top, with arrows indicating placement.
Step 9
Attach shelf supports (Part ID: 105494) to the inside of the cabinet using screws (Part ID: 101221). Two supports are used per shelf location.
Visual: A shelf support is shown being attached to the inner wall of the cabinet with a screw. A magnified view shows the screw being driven through the support into the panel.
Step 10
Attach additional shelf supports (Part ID: 105494) to the inside of the cabinet using screws (Part ID: 101221). This step appears to be for the lower section.
Visual: Similar to step 9, showing shelf supports being attached.
Step 11
Attach more shelf supports (Part ID: 105494) to the inside of the cabinet using screws (Part ID: 101221). This step shows the upper section.
Visual: Similar to step 9 and 10, showing shelf supports being attached.
Step 12
Insert a large number of screws (Part ID: 101221) into the pre-drilled holes along the edges of the cabinet. These likely serve as guides or attachment points for later steps.
Visual: The cabinet is shown with many screws being inserted into holes along its length. A magnified view shows the screw and the support (105494) it passes through.
Step 13
Attach mounting brackets (Part ID: 10068747 and Part ID: 10059781) to the back of the cabinet for wall mounting. Use screws (Part ID: 124431).
Visual: The back of the cabinet is shown. Mounting brackets are being attached using screws. A magnified view shows the bracket and screws.
Step 14
Attach foot housings (Part ID: 10056734) to the bottom of the cabinet. These likely receive the adjustable feet.
Visual: The bottom of the cabinet is shown. Foot housings are being attached. A magnified view shows the housing and its attachment.
Step 15
Attach the adjustable feet (Part ID: 123029) to the foot housings. The diagram shows the feet being screwed into the housings and then adjusted for leveling.
Visual: The cabinet is shown standing on its feet. A magnified view shows a foot being screwed into its housing and then adjusted using arrows indicating rotation.
Step 16
Attach wall mounting hardware to the cabinet. This step shows the cabinet being prepared for wall mounting.
Visual: The cabinet is shown with mounting hardware attached to the top back edge.
Step 17
Prepare for wall attachment. This step shows screws being used to secure the cabinet to the wall, with a warning icon indicating incorrect screw usage.
Visual: A screw is shown being driven into a wall. A magnified view shows a screw and a warning symbol indicating not to use a specific type of screw.
Step 18
Attach hinge plates (Part ID: 153647) to the inside of the cabinet doors. Use screws (Part ID: 10043569).
Visual: A cabinet door is shown. Hinge plates are being attached to the door using screws. A magnified view shows the hinge plate and screws.
Step 19
Attach hinge plates (Part ID: 10043569) to the cabinet frame. These plates will receive the hinges attached to the doors.
Visual: The cabinet frame is shown. Hinge plates are being attached to the frame using screws. A magnified view shows the plate and screws.
Step 20
Attach hinges (Part ID: 144553) to the hinge plates on the cabinet frame. The diagram shows the hinge being screwed into place.
Visual: A hinge is shown being attached to the hinge plate on the cabinet frame using screws. A magnified view shows the hinge and screws being tightened.
Step 21
Attach the doors to the cabinet by connecting the hinges on the doors to the hinges on the frame. Arrows indicate the movement for attachment.
Visual: The cabinet doors are shown being attached to the frame. Hinges are aligned and connected. Magnified view shows the hinge connection.
Step 22
Install the door rings (Part ID: 122619 and Part ID: 122584). These appear to be decorative or functional elements for the circular openings on the doors. They click into place.
Visual: The cabinet doors are shown with circular openings. Rings are being inserted and clicked into place. A magnified view shows the ring being pressed in until it clicks.
Step 23
Attach door stops (Part ID: 139244) to the inside of the cabinet doors. These likely prevent the doors from opening too far or hitting the sides.
Visual: A door stop is shown being attached to the inside of a cabinet door using screws. A magnified view shows the door stop and screws.
Step 24
Mark and drill holes in the wall for securing the cabinet. The diagram specifies a depth of 30mm (1 1/4") and a drill bit size of 5mm (3/16"). It also shows a warning icon indicating correct drilling technique.
Visual: A person is marking a wall and drilling a hole. A magnified view shows the drill bit size and depth, along with a warning symbol for proper drilling.
Step 25
Attach the cabinet to the wall using appropriate screws and wall plugs (not included). The diagram shows a screw (Part ID: 119976) being inserted through a bracket (Part ID: 106266) into the wall.
Visual: The cabinet is shown mounted to the wall. A magnified view shows a screw passing through a bracket into the wall.
Step 26
Insert covers (Part ID: 107091) into the designated holes on the cabinet, likely to conceal screw heads or attachment points.
Visual: Covers are shown being pushed into holes on the cabinet.
Step 27
Attach decorative caps or feet to the bottom of the cabinet using screws (Part ID: 124431) and caps (Part ID: 123029).
Visual: The bottom of the cabinet is shown. Caps are being attached using screws. A magnified view shows the cap and screw.
Step 28
Prepare the laundry bags for insertion. The diagram shows a bag being opened or unfolded.
Visual: A laundry bag is shown being unfolded or prepared.
Step 29
Insert the laundry bags into the cabinet. The diagram shows the bags being placed inside the cabinet compartments.
Visual: The cabinet is shown with laundry bags being inserted into the lower compartments.
Hinge Adjustment
Adjust hinges for proper door alignment. The diagram shows arrows indicating adjustment points on the hinges for left/right, in/out, and up/down movement.
Visual: Close-ups of hinges with arrows indicating adjustment directions.
