NYSJÖN Assembly Instructions

Important Safety Information

WARNING!

Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.

Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.

Always ensure that the furniture is securely attached to the wall to prevent tipping.

Tools Required

The following tools are typically needed for assembly:

• Screwdriver (Phillips head)
• Screwdriver (Flathead)
• Hammer
• Measuring tape
• Pencil
• Drill
• Safety glasses
• Level

Parts List

Identify all parts before assembly. Quantities are indicated.

• 16x Dowels (Part No. 123492)
• 16x Dowels (Part No. 101375)
• 1x Screw (Part No. 119976)
• 6x Screw (Part No. 124431)
• 16x Cam Lock (Part No. 102509)
• 8x Screw (Part No. 10048881)
• 4x Bracket (Part No. 10043569)
• 4x Bracket (Part No. 153647)
• 4x Bracket (Part No. 123029)
• 2x Foot/Cap (Part No. 10056734)
• 1x Bracket (Part No. 10059781)
• 1x Cap (Part No. 106266)
• 1x Screw (Part No. 107091)
• 2x Base Panel Component (Part No. 10032274)
• 2x Side Panel Component (Part No. 10048881)
• 3x Hinges (Part No. 144553)
• 2x Decorative Ring (Part No. 122619)
• 2x Decorative Ring (Part No. 122584)
• 3x Cover Plate (Part No. 139244)
• 1x Bag of Screws (Part No. 101221)

Assembly Steps

Step 1: Prepare Base Panel

Attach four brackets (Part No. 10048881) to the base panel components (Part No. 10032274) using four screws (Part No. 10048881).

Step 2: Insert Dowels

Insert sixteen dowels (Part No. 123492) into the pre-drilled holes on the base panel components.

Step 3: Attach Internal Dividers

Attach four internal divider panels to the base panel components. Use sixteen dowels (Part No. 101375) and sixteen screws (Part No. 119976) to secure them.

Step 4: Insert Dividers

Slide the attached internal divider panels into the designated slots on the base panel components.

Step 5: Install Cam Locks

Insert eight cam locks (Part No. 102509) into the corresponding holes on the internal divider panels.

Step 6: Position Top Panel

Carefully place the top panel onto the assembled structure, aligning it with the dowels and cam lock receivers.

Step 7: Secure Top Panel

Turn the eight cam locks (Part No. 102509) clockwise to secure the top panel to the structure.

Step 8: Attach Back Panel

Slide the back panel into the groove on the rear of the assembled unit.

Step 9: Secure Back Panel

Fasten the back panel using one screw (Part No. 101221).

Step 10: Attach Component A

Attach a component (Part No. 105494) to the unit using one screw (Part No. 101221).

Step 11: Attach Component B

Attach another component (Part No. 105494) to the unit using one screw (Part No. 101221).

Step 12: Prepare for Wall Mounting

Attach the main cabinet body to the wall mounting system. This involves inserting twenty-seven screws (Part No. 101221) into the designated points on the cabinet.

Step 13: Attach Wall Brackets to Cabinet

Attach two wall brackets (Part No. 124431) to the cabinet using two screws (Part No. 124431).

Step 14: Attach Wall Mounting Hardware

Attach two wall mounting hardware pieces (Part No. 10056734) to the cabinet using two screws (Part No. 10056734).

Step 15: Attach Feet

Screw two feet (Part No. 10056734) into the bottom of the cabinet.

Step 16: Wall Mounting - Cabinet Attachment

Lift the assembled cabinet and align it with the wall brackets previously installed on the wall. Secure the cabinet to the wall brackets.

Step 17: Secure Cabinet to Wall Brackets

Use four screws (Part No. 124431) to firmly attach the cabinet to the wall brackets.

Step 18: Install Wall Plates (Left Side)

Attach four wall mounting plates (Part No. 10043569) to the wall at the desired height and position. Ensure they are level.

Step 19: Install Wall Plates (Right Side)

Attach four wall mounting plates (Part No. 153647) to the wall at the desired height and position. Ensure they are level.

Step 20: Attach Hinges to Doors

Attach three hinges (Part No. 144553) to the cabinet doors using the provided screws.

Step 21: Attach Hinges to Cabinet Body

Mount the doors with attached hinges to the cabinet body by securing the hinges to the cabinet frame.

Step 22: Insert Decorative Rings

Press the two decorative rings (Part No. 122619) and two decorative rings (Part No. 122584) into the circular openings on the doors until they click into place.

Step 23: Attach Cover Plates

Attach three cover plates (Part No. 139244) to the hinges for a finished look.

Step 24: Wall Drilling Guide

For wall mounting, drill holes into the wall using a 5mm (3/16") drill bit. The recommended drilling depth is 30mm (1 1/4"). Ensure the drill is perpendicular to the wall.

Step 25: Attach Final Component

Attach the final component (Part No. 106266) using one screw (Part No. 119976) and one screw (Part No. 101221).

Step 26: Install Shelf Supports

Insert two shelf supports (Part No. 107091) into the desired positions inside the cabinet.

Step 27: Attach Feet

Attach two feet (Part No. 123029) to the bottom of the cabinet and secure them with screws (Part No. 124431).

Step 28: Assemble Fabric Baskets

Unfold and assemble the two fabric baskets.

Step 29: Insert Fabric Baskets

Place the assembled fabric baskets into the cabinet.

Adjustments

The hinges can be adjusted to ensure doors are aligned correctly. Refer to the detailed diagrams for hinge adjustment screws (typically for height, depth, and side-to-side alignment).