PREXISO PTD180 7" Digital Spirit Level

Product Description

The PREXISO PTD180 digital level angle gauge is a highly versatile leveling tool designed for fast, easy operation indoors. It can measure angles from 0-90° and 0-180°. The magnetic base is usable on any ferrous metal surface, with a V-shaped groove for alignment on pipes and conduits. It can be placed on the ground, saw blade, work bench, etc., to easily find desired slope lines.

Key Features

• 7-inch digital spirit level
• Angle measurement range: 0-90° and 0-180°
• Flip display for easy reading
• Magnetic base with V-groove for pipe alignment
• Multiple measurement units: Degrees (°), Percent (%), mm/m, IN/FT
• Audible buzzer for horizontal/vertical alignment
• Zero function for relative measurements
• Hold function to freeze readings
• Recalibration capability

Parts Description

• A: Bubble vial
• B: Zero function button
• C: Display screen
• D: Power ON/OFF and audible buzzer ON/OFF button
• E: Hold function and 90°/180° range switch button
• F: Mode switch function button
• G: Hanging hole
• H: Product label
• I: Battery compartment
• J: Magnets
• K: V-groove

Operation Instructions

1. Inserting the Battery

Open the battery compartment using a screwdriver and insert 2xAAA batteries, observing polarity. Remove batteries if the instrument is not used for a long time.

2. Switching ON/OFF

Press the power button to turn the device on. Press and hold the power button for over 3 seconds to turn it off. The device automatically shuts off after 3 minutes of inactivity.

3. Level Measurement

Turn on the tool and place it in the desired position. The display auto-rotates 180° for easier reading. Auto-rotation is triggered when the device rotates more than 90° from its starting point and continues to rotate more than 10°.

4. Unit of Angle Measurement Selection

After powering on, the screen shows the slope in degrees. Short-press the mode button to cycle through units: Degrees (°), Percent (%), mm/m, and IN/FT (pitch readings in 1/8-inch/feet increments).

5. Angle Measurement Range Selection

The tool can display measurements from 0-90° or 0-180°. Press and hold the 90°/180° button for 2 seconds to switch between ranges. The display shows an icon for the selected range (90° or 180°).

6. Zero Function

To set a reference plane, short-press the zero button. The current angle is set to ZERO, and the zero indicator will flash on the display. Once it stops flashing, the device is in relative angle measurement mode. Press the zero button again to return to absolute level measurement.

7. Hold Function

To freeze the current measurement for easier reading, short-press the hold button. A hold indicator will appear on the display. Press the hold button again to return to measuring mode. The measurement value remains on the display until the button is pressed again.

8. Audible Buzzer

When the tool is on, press the buzzer button. The buzzer alerts when the device is within +/-1° of horizontal or vertical. The alert frequency changes based on proximity. A continuous alert sounds at perfect horizontal or vertical positions. Press the button again to turn off the buzzer.

9. Recalibration

a. Turn off the equipment. Place it on a flat, smooth, solid surface.
b. With the device off, press and hold the MODE button, then press the power button until "CAL 1" appears on the LCD.
c. Keep the equipment still, then press the MODE button. "CAL 1" will flash, then "CAL 2" will appear.
d. Rotate the equipment 180° in the same location, then press the MODE button. "CAL 2" will flash. Calibration is complete when "CAL 2" disappears, and the current angle will be shown.

Technical Specifications

Safety Instructions

Important: Read Before Using

Safety instructions and user manual should be read carefully before first use.

General Safety

• Keep the instrument dry.
• Keep the instrument and battery out of reach of infants and children.
• Replace batteries when the low battery symbol [low battery symbol] appears. Ensure correct polarity. Remove battery if not in use for a long time.

Prohibited Use

• Using the product without instruction.
• Using outside the stated limits.
• Deactivating safety systems or removing labels.
• Opening the equipment with tools.
• Modifying or converting the product.
• Using accessories from other manufacturers without express approval.

Limits of Use

Designed for habitable areas. Do not use in explosion-hazardous areas or aggressive environments.

Responsibilities of the Person in Charge

• Understand safety instructions and user manual.
• Be familiar with local safety regulations.
• Prevent unauthorized access.

Maintenance

This is a low-maintenance tool. To maintain performance:

• Avoid shock, vibration, or extreme temperatures.
• Store indoors.
• Keep free of dust and liquids. Clean with a soft cloth, slightly moistened with pure alcohol or water if necessary.
• Do not disassemble the tool.

Disposal

Do not dispose of batteries with household waste. Dispose of batteries and the product according to national and local regulations to protect the environment.

Warranty

Two-Year Limited Warranty. This product is warranted to the original purchaser for two years from the original purchase date against defects in material and workmanship. Contact Prexiso customer service at info@prexiso-eu.com for warranty claims. Warranty does not cover normal wear, abuse, unauthorized modifications, rental use, or shipping damage. Prexiso will replace or repair defective units at its discretion. Implied warranties are limited. Prexiso is not liable for incidental or consequential damages. This warranty excludes accessories.

EC Declaration of Conformity

Hangzhou GreatStar Industrial Co., Ltd. declares that the product complies with relevant EC Directives (EMC Directive 2014/30/EU) and harmonized standards (EN 61326-1:2021, IEC 62133-2:2017, EN 62133-2:2017). Responsible for documentation: GreatStartools Germany GmbH.