Manuals+

Baby Trend PROtect™ Premiere Convertible Car Seat

OWNER'S MANUAL

⚠️ WARNING!

Carefully read and understand all instructions and warnings in this manual. Failure to properly use this Car Seat increases the risk of SERIOUS INJURY or DEATH in a sudden stop or crash.

KEEP INSTRUCTIONS FOR FUTURE USE.

Store this manual in the pocket provided on the side of the car seat base. Store this manual in the pocket provided on the rear of the Car Seat Pad.

For instructions in Español, connect to www.babytrend.com or call: 1-800-328-7363.

WARRANTY

DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND FOR REPLACEMENT PARTS, SERVICE AND REPAIR.

The Baby Trend® warranty covers workmanship defects within the first 180 days of purchase. Any product subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration, or accident, or with an altered/removed serial number, invalidates all claims. Damage to property during installation is the end user's sole responsibility.

Contact Customer Service: 1 (800) 328-7363, Monday through Friday, 8:00 am - 4:30 pm (PST). Return Authorizations are required. Warranty valid only in North America.

1.0 General Warnings and Information

⚠️ WARNING! DEATH or SERIOUS INJURY can occur:

Unsecured child restraints can injure others in a crash.

Direct sunlight can make Convertible Seat surfaces hot enough to burn your child. Use caution and check the vehicle and Convertible Seat on hot, sunny days.

NEVER leave a child unattended under any circumstance.

DO NOT use this Convertible Seat if it has been in a crash.

DO NOT use this Convertible Seat if it is damaged or has missing parts.

STOP USING THIS Convertible Seat AND THROW IT AWAY after the date on the back of the seat. Dispose of it properly.

NEVER use this Convertible seat in the home, on boats, or in motor homes with side-facing seats or other non-certified uses. Only use this restraint in Automobiles and Aircraft.

NEVER use this Convertible Seat in any vehicle seating position equipped with an active air bag. Read your vehicle's owner manual to turn off your airbag if necessary. For side airbags, see section 4.1.

2.0 Use Recommendations

Children should use a child restraint with a built-in harness system until they exceed the weight or height limits specified by the manufacturer.

2.1 Rear facing without the upper seatback

Weight and Height Requirements:

This child restraint, without the upper seatback in a rear facing position, is designed for children whose:

Child MUST meet BOTH of these requirements to use this Convertible Seat without the upper seatback installed.

Figure 5a: Depicts the car seat in a rear-facing position without the upper seatback.

Figure 5b: Shows a label reference for the maximum height line.

2.2 Rear facing with the upper seatback

Weight and Height Requirements:

This child restraint, WITH the upper seatback installed in a rear facing position, is designed for children whose:

Child MUST meet BOTH of these requirements to use this Convertible Seat.

Figure 6a: Depicts the car seat in a rear-facing position with the upper seatback installed.

Figure 6b: Illustrates the 1 inch (2.54 cm) measurement for head clearance.

2.3 Forward facing seat requirements

Weight and Height Requirements:

This child restraint, with the upper seatback installed in a forward facing position, is designed for children whose:

Child MUST meet ALL of these requirements to use this Convertible Seat forward facing.

Figure 7: Shows the car seat in a forward-facing position with a child secured.

NEVER install the car seat in a forward facing position without the upper seat back installed.

3.0 Convertible Seat Parts

The convertible seat includes the following parts:

4.0 Selecting a Vehicle Seating Location

⚠️ WARNING! DEATH or SERIOUS INJURY can occur:

4.1 Proper Installation

  1. The National Highway Traffic Safety Administration (NHTSA) advises that children under age 13 are safer in rear seating positions.
  2. Refer to your vehicle owner's manual for car seat installation instructions.
  3. Use convertible seats in a rear seat location whenever possible.
  4. Follow LATCH anchor connector points maximum weight ratings.
  5. Never place the Convertible Seat in a front seat location unless recommended by the vehicle owner's manual.
  6. For vehicles with airbags, refer to the vehicle owner's manual for child restraint installation information. If a front seat location with an airbag must be used, follow the vehicle manufacturer's instructions and move the vehicle seat back as far as possible.

Baby Trend Policy Statement: Use Of PROtect™ Car Seat Series Convertible Car Seat Child Restraint In Conjunction With Side Airbags

Refer to your owner's manual to determine your vehicle's side impact air bag types for individual seating positions. The Baby Trend PROtect™ Car Seat Series Convertible Car Seat may be used in any rear seating position equipped only with roof-mounted, "curtain" type side impact airbags. For other types of side impact airbags, consult your vehicle's owner's manual or the automobile manufacturer.

4.2 Vehicle Seats to Avoid

DO NOT use this Convertible Seat with the following vehicle seats:

4.3 Vehicle Seat Belt Systems

Use only the vehicle's lap and shoulder belt, lap belt, or LATCH system when restraining this Convertible Seat.

Vehicle seat belt systems vary. Not all vehicle seat belts can be used with a child restraint. Refer to the information in this section on the various types of vehicle seat belt systems.

4.4 Vehicle Seat Belt Systems to Avoid

DO NOT use this Convertible Seat with the following vehicle seats:

4.5 LATCH Lower Anchors

Consult your vehicle owner's manual or manufacturer for location and availability of LATCH anchor points. Not all vehicles have the same locations or maximum weight requirements for LATCH!

Diagram shows typical Lower Anchor Point Locations.

4.6 LATCH - Top Tether Anchor Locations

Top Tether Locations are indicated by the following symbol: ⚓ (LATCH Top Tether symbol).

Consult your vehicle owner's manual for your vehicle's exact LATCH locations, anchor identification, and usage requirements.

Maximum Child Weight for LATCH: Lower Anchor 45 lbs (20.4 kg), Top Tether 65 lbs (29.5 kg).

Vehicle LATCH locations may vary:

5.0 Installation and Use

⚠️ WARNING! DEATH or SERIOUS INJURY can occur:

5.1 Child Placement in Restraint

Routing paths for forward facing installation:

  1. Place child in the restraint with their back flat against the back of the restraint and bottom touching the seat.
  2. Rear Facing: Harness Strap should be at or below the shoulder. Forward Facing: Harness Strap Height should be at or slightly above the child's shoulder. Note: Forward facing occupants weighing more than 32 lbs (14.5kg) or 35 inches (88.9 cm) MUST use height position 4.
  3. Place 5-point crotch buckle in the rear position (rear-facing) or outer position (forward-facing).
  4. Insert buckle tongues into the buckle. Pull up to test security.
  5. Place chest clip at armpit level. Insert tabs, press together, pull outward to test security.
  6. Pull harness adjuster to tighten harness straps. A snug strap should not allow slack, lie straight, and not press on skin or push body unnaturally. To loosen, push the harness tension adjuster button and gently pull straps.

5.2 Rear Facing Installation with Lap/Shoulder Belt

Requirements: See section 2.1 (Weight 5-22 lbs, head not at max height line).

Routing paths for rear facing installation:

⚠️ WARNING! Never use a Top Tether connector in a rear facing installation!!

The Convertible car seat, in a Rear Facing installation, was designed with a removable upper seatback to allow for proper installation when it contacts the front seat. If the upper seatback prevents a 45-degree installation, remove it and install the Convertible at 45 degrees per instructions. To remove the upper seatback, refer to section 5.11. Reinstall the upper seat back when the child reaches 22 lbs (9.98 kg), or the child's head nears the max height red line. Keep child rear-facing as long as possible. Contact Baby Trend Customer Service at 1-800-328-7363 for questions.

Rear Facing Installation with Lap/Shoulder Belt. With Headrest

Requirements: See section 2.2 (Weight 5-40 lbs, head 1 inch below top).

  1. Squeeze recline handle and recline the seat to positions 1, 2, or 3. Angling the seat helps keep the baby's head back and airway open. Note: A rolled up towel or pool noodle can be used for extra elevation and angle adjustment.
  2. Place restraint in a rear seating position and ensure the vehicle is level.
  3. Unsnap the 2 front snaps and the 2 side snaps. Lift and fold back padding.

Diagrams illustrate routing paths and installation steps.

  1. Route lap/shoulder belt through the rear facing safety belt path. Remove any twist in webbing to ensure it lies flat.
  2. Put weight in the seat, compress the vehicle seat cushion, insert the seat buckle tongue into the buckle, and pull the seat belt tight. Pull up on the buckle to ensure it is secure.
  3. Lower flap and secure hook and loop fasteners and all snaps.
  4. Ensure the rear facing angle indicator bubble is located between the boundary lines.
  5. Check for movement of the restraint at the safety belt path. The restraint should not move more than 1 inch in any direction. Repeat all steps until all safety steps are met.

5.3 Rear Facing Installation with Lap Belt

Requirements: See section 2.1 (Weight 5-22 lbs, head not at max height line).

Routing paths for rear facing installation:

⚠️ WARNING! Never use a Top Tether connector in a rear facing installation!!

The Convertible car seat, in a Rear Facing installation, was designed with a removable upper seatback to allow for proper installation when it contacts the front seat. If the upper seatback prevents a 45-degree installation, remove it and install the Convertible at 45 degrees per instructions. To remove the upper seatback, refer to section 5.11. Reinstall the upper seat back when the child reaches 22 lbs (9.98 kg), or the child's head nears the max height red line. Keep child rear-facing as long as possible. Contact Baby Trend Customer Service at 1-800-328-7363 for questions.

Rear Facing Installation with Lap Belt. With Headrest

Requirements: See section 2.2 (Weight 5-40 lbs, head 1 inch below top).

  1. Squeeze recline handle and recline the seat to positions 1, 2, or 3. Angling the seat helps keep the baby's head back and airway open. Note: A rolled up towel or pool noodle can be used for extra elevation and angle adjustment.
  2. Place restraint in a rear seating position and ensure the vehicle is level.
  3. Unsnap the 2 front snaps and the 2 side snaps. Lift and fold back padding.

Diagrams illustrate routing paths and installation steps.

  1. Route lap belt through the rear facing safety belt path. Remove any twist in webbing to ensure it lies flat.
  2. Put weight in the seat, compress the vehicle seat cushion, insert the seat buckle tongue into the buckle, and pull the seat belt tight. Pull up on the buckle to ensure it is secure.
  3. Lower flap and secure hook and loop fasteners and all snaps.
  4. Ensure the rear facing angle indicator bubble is located between the boundary lines.
  5. Check for movement of the restraint at the safety belt path. The restraint should not move more than 1 inch in any direction. Repeat all steps until all safety steps are met.

5.4 Rear Facing Installation with LATCH Lower Anchor

Requirements: See section 2.1 (Weight 5-22 lbs, head not at max height line).

⚠️ WARNING! Never use a Top Tether connector in a rear facing installation!!

The Convertible car seat, in a Rear Facing installation, was designed with a removable upper seatback to allow for proper installation when it contacts the front seat. If the upper seatback prevents a 45-degree installation, remove it and install the Convertible at 45 degrees per instructions. To remove the upper seatback, refer to section 5.11. Reinstall the upper seat back when the child reaches 22 lbs (9.98 kg), or the child's head nears the max height red line. Keep child rear-facing as long as possible. Contact Baby Trend Customer Service at 1-800-328-7363 for questions.

Rear Facing Installation with LATCH Lower Anchor. With Headrest

Requirements: See section 2.2 (Weight 5-40 lbs, head 1 inch below top).

  1. Squeeze recline handle and recline the seat to positions 1, 2, or 3. Angling the seat helps keep the baby's head back and airway open. Note: A rolled up towel or pool noodle can be used for extra elevation and angle adjustment.
  2. Place restraint in a rear seating position and ensure the vehicle is level.
  3. Unsnap the 2 front snaps and the 2 side snaps. Lift and fold back padding.

Diagrams illustrate routing paths and installation steps.

  1. Route LATCH belt through the rear facing safety belt path, leaving the adjuster side of the LATCH belt on the child's LEFT side. Remove any twist in webbing to ensure it lies flat.
  2. Attach the LATCH connector to the vehicle's LATCH anchor with the release button facing downwards. Ensure the adjuster side of the LATCH belt is on the left side of the car seat. Note: If the adjuster is facing the wrong direction or the LATCH connector is upside down, the restraint will not secure properly.
  3. Put weight in the seat, compress the vehicle seat cushion, attach the LATCH connector to the vehicle's LATCH anchor, and pull the adjuster belt tight. Pull up on the LATCH connector to ensure it is secure.
  4. Lower flap and secure hook and loop fasteners and all snaps.
  5. Ensure the rear facing angle indicator bubble is located between the boundary lines.
  6. Check for movement of the restraint at the safety belt path. The restraint should not move more than 1 inch in any direction. Repeat all steps until all safety steps are met.

5.5 Forward Facing Installation with Lap/shoulder Belt and Top Tether

Requirements: See section 2.3 (Weight 23-65 lbs, Height 50 inches or less, Age 1 year).

  1. Ensure harness is adjusted to position 3 or 4. Use recline positions 5 and 4 for forward facing.
  2. Ensure vehicle is level, the Convertible is placed flat, and rests on the front outer edge of the vehicle seat.
  3. Lift back flap and place harness to side.

Installation Steps:

  1. Route lap/shoulder belt through the forward facing belt path.
  2. Put weight in seat, compress the automobile seat cushion, insert the buckle tongue into the buckle, and adjust seat belt as tight as possible. Pull up on buckle tongue to ensure it is secure.
  3. Lower flap and secure hook and loop fasteners.
  4. Attach Top Tether to a designated anchor point. Pull Top Tether strap until webbing strap is snug. Note: Your vehicle owner's manual will provide anchor locations and maximum weight of the restraint's occupant for LATCH connections.
  5. Check for movement of the restraint at the safety belt path. The restraint should not move more than 1 inch in any direction. Repeat all steps until all safety steps are met.

Diagrams illustrate routing paths and installation steps.

5.6 Forward Facing Installation with Lap Belt and Top Tether

Requirements: See section 2.3 (Weight 23-65 lbs, Height 50 inches or less, Age 1 year).

  1. Ensure harness is adjusted to position 3 or 4. Use recline positions 5 and 4 for forward facing.
  2. Ensure vehicle is level, the Convertible is placed flat, and rests on the front outer edge of the vehicle seat.
  3. Lift back flap and place harness to side.

Installation Steps:

  1. Route lap belt through the forward facing belt path.
  2. Put weight in seat, compress the automobile seat cushion, insert the buckle tongue into the buckle, and adjust seat belt as tight as possible. Pull up on buckle tongue to ensure it is secure.
  3. Lower flap and secure hook and loop fasteners.
  4. Attach Top Tether to a designated anchor point. Pull Top Tether strap until webbing strap is snug. Note: Your vehicle owner's manual will provide anchor locations and maximum weight of the restraint's occupant for LATCH connections.
  5. Check for movement of the restraint at the safety belt path. The restraint should not move more than 1 inch in any direction. Repeat all steps until all safety steps are met.

Diagrams illustrate routing paths and installation steps.

5.7 LATCH - Forward Facing Installation with Lower Anchor and Top Tether

NOTE: Use the vehicle's seat belt (not LATCH) for children weighing more than 45 lbs (20.5 kg).

Requirements: See Section 2.3 (Weight 23-45 lbs, Height 50 inches or less, Age 1 year).

  1. Place restraint in a rear seating position designated as lower anchor compatible. Refer to your vehicle owner's manual for LATCH locations.
  2. Ensure vehicle is level, the Convertible is placed flat, and rests on the front outer edge of the vehicle seat. Ensure harness is adjusted to position 5 or 4. Only use recline positions 5 and 4 for forward facing.
  3. Lift back flap and place harness to side.

Installation Steps:

  1. Route LATCH belt through the front facing safety belt path, leaving the adjuster side of the LATCH belt on the child's RIGHT side. Remove any twist in webbing to ensure it lies flat.
  2. Put weight in the seat, compress the vehicle seat cushion, attach the LATCH connector to the vehicle's LATCH anchor, and pull the adjuster belt tight. Pull up on the LATCH connector to ensure it is secure.
  3. Lower flap and secure hook and loop fasteners.
  4. Attach Top Tether to a designated anchor point. Pull Top Tether strap until webbing strap is snug. Note: Your automobile's owner's manual will provide anchor locations and maximum weight of the restraint's occupant for LATCH connections.
  5. Check for movement of the restraint at the safety belt path. The restraint should not move more than 1 inch in any direction. Repeat all steps until all safety steps are met.

Diagrams illustrate routing paths and installation steps.

5.8 LATCH Connector Belt Rerouting

The correct belt path must be used for proper installation.

Reroute From Forward Facing Belt Path to Rear Facing Belt Path:

  1. Unthread LATCH belt out of the front facing safety belt path.
  2. Unsnap the 2 front snaps and the 2 side snaps. Lift and fold back padding.

Reroute From Rear Facing Belt Path to Front Facing Belt Path:

  1. Unthread LATCH belt out of the rear facing safety belt path.
  2. Route LATCH belt through the front facing safety belt path, leaving the adjuster side of the LATCH belt on the child's RIGHT side. Remove any twist in webbing to ensure it lies flat.
  3. Lower flap and secure hook and loop fasteners and all snaps.

Diagrams illustrate rerouting steps.

5.9 Aircraft Installation

  1. Follow the seat belt installation for use in an Aircraft.
  2. Consult your airline for requirements to use this restraint.

5.10 Child Placement in Restraint

  1. Place child in the restraint with their back flat against the back of the restraint and bottom touching the seat.
  2. Rear Facing: Harness Strap should be at or below the shoulder. Forward Facing: Harness Strap Height should be at or slightly above the child's shoulder. Note: Forward facing occupants weighing more than 32 lbs (14.5kg) or 35 inches (88.9 cm) MUST use height position 4. Then place harness straps over the child's shoulders. Note: Check that the harness straps are just above the child's shoulders.
  3. The Convertible has been safety tested with the height insert and head pillow. The height insert is needed until the child's shoulder is at or above position 1.

Diagrams illustrate child placement and harness adjustment.

5.11 Shoulder Height Adjustment

Shoulder Height Positions:

Height Adjustment:

  1. Pull harness release handles outward.
  2. Raise or lower to the appropriate position.

Diagrams show shoulder height positions and adjustment.

5.12 Crotch Buckle Position

  1. Press the crotch buckle release button down with fingers and move position.
  2. Crotch buckle placement:
    • Rear facing: rear most position.
    • Forward facing: forward most position.

Diagram shows crotch buckle placement.

5.13 Harness Length Adjustment

A- Protect convertible manufactured before 03/20/2017 Follow A.1. Protect convertible manufactured on or after 03/20/2017 Follow A.2.

  1. Unhook the harness straps from the metal plate and move to the desired adjustment.
  2. A.1: Feed one Harness Strap Connector plate through each Harness Strap End. Rotate the other Harness Strap Connector plate and feed through each Harness Strap End. Ensure straps are securely connected to both connector plates.
  3. A.2: Feed one Harness Strap Connector plate through each Harness Strap End. Ensure both straps are securely connected to the connector plate. Only splitter plates with “Single Use Approved BT 2016” are approved for single use.

Inspect harness straps for twists. Twisted straps can prevent proper tightening and may not adequately restrain your child. Before using, pull harness straps from the front to ensure they are securely re-attached.

Diagrams illustrate harness adjustment steps.

5.14 Locking Clip Use

If your vehicle lap/shoulder belt requires a Locking Clip to prevent loosening after installation, thread the locking clip on the belt as close to the latch plate as possible – within 1 inch (2.54 cm).

Diagram shows locking clip placement.

5.15 Upper Seat Back Removal and Installation

⚠️ WARNING: The upper seat back must be installed when the child weighs more than 22 lbs (9.98 kg) or the top of their head has reached the max height red line on the seat back, or the restraint is forward facing.

  1. Removal: Lift the release tab and pull up on the upper seat back. NOTE: DO NOT store the upper seat back in the passenger compartment. Store it in a secure location like your trunk or garage.
  2. Installation: Align the upper seat back rods with the openings and push until the seat back locks into place. Pull up on the upper seat back to ensure it is locked.

Diagrams show removal and installation steps.

5.16 Pad Removal & Laundering

Pad Removal:

  1. Unfasten the 4 elastic loops on the bottom of the Convertible and the 8 snaps on the edge of the pad.
  2. Lift the seatback flap.
  3. Remove the upper seat back.
  4. Unfasten 4 snaps and remove the upper seat pad.

To Launder:

  1. Hand wash in cool water with mild detergent and hang to dry. NOTE: DO NOT machine wash or dry.

Diagrams illustrate pad removal.

5.18 Pool Noodle or Rolled Towel Use

Extra Elevation:

  1. A pool noodle or rolled towel can be used for extra elevation.
  2. Place the noodle or rolled towel where the seat bottom and seat back meet.

Diagram shows placement for extra elevation.

6.0 Safety

6.1 Safe Practices

For assistance with installation or use, contact:

EVERYONE rides buckled up or the vehicle DOES NOT GO! Make NO EXCEPTIONS for adults or children!

6.2 Safety Checklist

Review these questions to ensure proper use:

Please Drive Safely

7.0 Additional Information

7.1 Certification

This child restraint system conforms to all applicable Federal Motor Vehicle Safety Standards for use in motor vehicles. This Convertible Seat is certified for use in motor vehicles.

7.2 Aircraft Use

  1. Follow the vehicle lap belt installation for use in an Aircraft.
  2. Consult your airline for requirements to use this restraint.

7.3 Vehicle Seat Protection

Protect the vehicle seat. Use a thin car seat mat, thin towel, or thin blanket under and behind the Convertible Seat.

7.4 Instruction Manual Storage

Store instruction manual in the pocket on the side of the Convertible Seat.

7.5 Convertible Seat Useful Life

DO NOT use this Convertible Seat after the date on the back of the seat. Parts may be missing, damaged, or the Convertible Seat may have been in a crash.

8.0 Registration Information

REGISTER YOUR CAR SEAT

Please complete the following information. The model number and manufactured date can be found on a label on the bottom of the Car Seat.

Model Number: ___________________

Manufactured in: __________________

Purchase Date: ___________________

Please fill out the prepaid registration post card attached to the harness straps and mail it today.

Child restraints can be recalled for safety reasons. You must register this restraint to be reached in a recall. Send your name, address, e-mail address (if available), and the restraint's model number and manufacturing date to: Baby Trend®, Inc., 1607 S. Campus Avenue, Ontario, CA 91761 or call 1-800-328-7363 or register online at: http://www.babytrend.com/registration.html. For recall information, call the U.S. Government's Vehicle Safety Hot line at 1-888-327-4236 (TTY: 1-800-424-9153), or go to http://www.NHTSA.gov.

If You Need Help

Contact Customer Service with any questions. Have the model and manufactured date ready. This information is on a white label on the bottom of the car seat.

USA Toll Free: 1-800-328-7363

Hours: 8:00 am to 4:30 pm (PST) Monday - Friday

Website: www.babytrend.com

9.0 Care and Cleaning

9.1 Removing Seat Pad, Back Pad and Headrest Pad

Follow directions in section 5.12.

9.2 Cleaning Seat Pad, Head Bolster and Height Insert

9.3 Cleaning Shell

9.4 Replacement Parts

For help or replacement parts, call Customer Service at 1-800-328-7363 (8:00 am - 4:30 PM PST, Monday-Friday) or visit www.babytrend.com.

US PATENTS 7 901 003 AND 8 096 613. OTHER US AND FOREIGN PATENTS PENDING.

PDF preview unavailable. Download the PDF instead.

cv88a en 032317 ?2190 Adobe PDF Library 11.0 Adobe InDesign CC (Macintosh)

Related Documents

Preview Baby Trend PROtect Elite Convertible Car Seat Owner's Manual
Comprehensive owner's manual for the Baby Trend PROtect Elite Convertible Car Seat (Model CV88C), providing detailed instructions on installation, use, safety, and care for optimal child safety.
Preview Baby Trend CV88 PROtect Sport Convertible Car Seat Owner's Manual
Comprehensive owner's manual for the Baby Trend CV88 PROtect Sport Convertible Car Seat, covering installation, usage, safety guidelines, care, and registration.
Preview Baby Trend Trooper PLUS 3-in-1 Convertible Car Seat Owner's Manual
Comprehensive owner's manual for the Baby Trend Trooper PLUS 3-in-1 Convertible Car Seat, covering installation, safety, use, and care instructions. Learn how to properly secure your child for maximum safety.
Preview Baby Trend CV88D Premiere Plus Convertible Car Seat Owner's Manual
This owner's manual provides comprehensive instructions for the Baby Trend CV88D Premiere Plus Convertible Car Seat, covering installation, usage, safety guidelines, care and cleaning, and warranty information.
Preview Baby Trend Trooper 3-in-1 Convertible Car Seat Owner's Manual
Comprehensive owner's manual for the Baby Trend Trooper 3-in-1 Convertible Car Seat, detailing installation, safety guidelines, usage recommendations, and care instructions.
Preview Baby Trend Trooper 3-in-1 Convertible Car Seat Owner's Manual
This owner's manual provides comprehensive instructions for the Baby Trend Trooper 3-in-1 Convertible Car Seat. It covers safety warnings, use recommendations, installation procedures (rear-facing and forward-facing using seat belts or LATCH), child placement, care and cleaning, and warranty information.
Preview Baby Trend PROTECT 2-in-1 Folding Booster Seat Owner's Manual
This owner's manual provides essential information for the Baby Trend PROTECT 2-in-1 Folding Booster Seat, covering safety warnings, usage recommendations, installation guides, care instructions, and warranty details.
Preview Baby Trend Hybrid 3-in-1 Car Seat Owner's Manual
Comprehensive owner's manual for Baby Trend Hybrid PLUS and Hybrid LX 3-in-1 Car Seats. Learn about installation, safety features, use modes (Toddler, Booster), and maintenance for optimal child safety.