Baby Trend CV88 PROtect Sport Convertible Car Seat

Store this manual in the pocket provided on the rear of the Car Seat Pad.

WARRANTY

DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND FOR REPLACEMENT PARTS, SERVICE AND REPAIR.

The Baby Trend® warranty covers workmanship defects within the first 180 days of purchase. Any product which has been subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration or accident, or has had its serial number altered or removed invalidates all claims against the manufacturer. Any damage to property during installation is the sole responsibility of the end user. The Customer Service Department can be contacted at 1 (800) 328-7363 Monday through Friday between 8:00am and 4:30pm (PST). Return Authorizations are required prior to returning product(s) to Baby Trend®. Warranty only valid in North America.

For instructions in Spanish, visit www.babytrend.com or call 1-800-328-7363.

WARNING

Carefully read and understand all instructions and warnings in this manual. Failure to properly use this Car Seat increases the risk of SERIOUS INJURY or DEATH in a sudden stop or crash.

KEEP INSTRUCTIONS FOR FUTURE USE. Store this manual in the pocket provided on the side of the car seat base.

Model: CV88 PROtect™ Car Seat Series Sport Convertible Car Seat

Table of Contents

(Content omitted for brevity as per instructions)

1.0 General Warnings and Information

WARNING! DEATH or SERIOUS INJURY can occur:

• Failure to follow these instructions and Convertible Seat labels can result in injury or death to a child from striking the vehicle's interior during a sudden stop or crash.
• Even if the Convertible Seat seems easy to use, it is important to read these instructions and the vehicle owner's manual.
• Follow both this manual and your vehicle's owner's manual. If there is a conflict, the vehicle owner's manual takes precedence regarding seat belts, LATCH, or airbags.
• Failure to use or properly adjust the automobile seat belt can result in serious injury or death to your child during a crash.
• Only allow others to use this seat if they understand the instructions and can demonstrate proper use.
• Use only Baby Trend car seat accessories. Other accessories may compromise safety.
• DO NOT modify or attach toys, padding, or other items. Untested modifications could result in injury.
• Secure the seat with the vehicle seat belt or LATCH bars at all times, even when unoccupied. An unsecured restraint can injure others in a crash.
• Direct sunlight can make seat surfaces hot. Check the seat on hot, sunny days.
• NEVER leave a child unattended.
• DO NOT use this Convertible Seat if it has been in a crash. It may have hidden damage and must be replaced.
• DO NOT use this Convertible Seat if it is damaged or missing parts.
• STOP USING THIS Convertible Seat AND THROW IT AWAY after the date on the back of the seat. Do not sell it.
• NEVER use this seat in a home, on boats, or in motor homes with side-facing seats. Only use in automobiles and aircraft.
• NEVER use this seat in a vehicle seating position equipped with an active airbag. Consult your vehicle's manual to turn off airbags if a child must ride in the front seat. For side airbags, see section 4.1.

2.0 Use Recommendations

Children should use a child restraint with a built-in harness system until they exceed the manufacturer's specified weight or height limits.

2.1 Rear facing without the upper seatback

Weight and Height Requirements: For children whose:

• Weight is between 5 and 22 lbs (2.3 and 10 kg), AND
• Top of head has NOT reached the max height red line on the seat back.

Child MUST meet BOTH requirements.

Illustration reference: Fig. 5a shows the seat in rear-facing position without upper seatback. Fig. 5b indicates the max height line.

2.2 Rear facing with the upper seatback

Weight and Height Requirements: For children whose:

• Weight is between 5 and 40 lbs (2.3 kg and 18.1 kg), AND
• Head is 1 inch below the top of the seat.

Child MUST meet BOTH requirements.

Illustration reference: Fig. 6a shows the seat in rear-facing position with upper seatback. Fig. 6b indicates the 1-inch clearance.

2.3 Forward facing seat requirements

Weight and Height Requirements: For children whose:

• Weight is between 23 and 65 lbs (10.43 kg and 29 kg), AND
• Height is 50 inches (127 cm) or less, AND
• Age is 1 year old.

Child MUST meet ALL requirements for forward-facing use.

WARNING: NEVER install the car seat in a forward-facing position without the upper seat back installed.

Illustration reference: Fig. 7 shows a child in the forward-facing position.

3.0 Convertible Seat Parts

Diagrams illustrate various parts of the convertible car seat. Key components include:

• Removable upper seat back
• Seat pad
• Harness pads
• Chest clip
• 5-point harness buckle
• Armrest
• Cup holder
• Lower anchor connectors
• Harness tension adjuster
• Recline foot
• Instruction holder
• Upper Seat back release
• Top tether

4.0 Selecting A Vehicle Seating Location

WARNING! DEATH or SERIOUS INJURY can occur:

• Only use this seat with the vehicle's seat belts or LATCH System.
• DO NOT use with seat belts mounted to the vehicle door or door frame.
• DO NOT use if it cannot be properly installed; some restraints do not fit all seating positions.
• NEVER use in any seating position equipped with an active air bag. Consult your vehicle's manual to turn off airbags. For side airbags, see Section 4.1.
• DO NOT use in the rear seat of a compact pickup truck.
• DO NOT use in vehicles with side-facing or rear-facing vehicle seats. See Section 4.2.
• NEVER install without the upper seat back installed in forward-facing position.
• NEVER use in forward-facing position with the upper seatback removed.
• NEVER attach two LATCH lower anchors to the same attachment point.
• NEVER use both LATCH lower anchors and vehicle seat belts simultaneously.

4.1 Proper Installation

The National Highway Traffic Safety Administration (NHTSA) states children under 13 are safer in rear seating positions.

1. Refer to your vehicle owner's manual for car seat installation instructions.
2. Use rear seat locations whenever possible.
3. Follow LATCH anchor connector point maximum weight ratings.
4. Never place the seat in a front seat unless recommended by the vehicle owner's manual.
5. For vehicles with airbags, refer to the owner's manual for child restraint installation. If a front seat must be used, follow manufacturer instructions and move the vehicle seat back as far as possible.

Baby Trend Policy Statement on Side Airbags: Refer to your vehicle owner's manual to determine side impact airbag types. This restraint may be used in rear seating positions equipped with roof-mounted "curtain" type side impact airbags. For other types, consult your owner's manual or the automobile manufacturer.

4.2 Vehicle Seats to Avoid

DO NOT use this Convertible Seat with the following vehicle seats:

• Seats facing SIDES of vehicle.
• Seats facing REAR of vehicle.
• Rear seats of small extended cab pickup trucks.

4.3 Vehicle Seat Belt Systems

Use only the vehicle's lap and shoulder belt, lap belt, or LATCH system. Seat belt systems vary by vehicle; not all are compatible. Refer to this section for information on different seat belt systems.

4.4 Vehicle Seat Belt Systems to Avoid

DO NOT use this Convertible Seat with the following vehicle seats:

• Passive restraints with motorized shoulder belt.
• Passive restraints with lap or shoulder belts mounted on the front door.

4.5 LATCH Lower Anchors

Consult your vehicle owner's manual or manufacturer for LATCH anchor point location and availability. Not all vehicles have the same locations or maximum weight requirements for LATCH.

Diagrams show typical Lower Anchor Point Locations.

4.6 LATCH - Top Tether Anchor Locations

Top Tether Locations are indicated by the tether symbol.

Consult your vehicle owner's manual for exact LATCH locations, anchor identification, and usage requirements.

Maximum Child Weight for LATCH: Lower Anchor 45 lbs (20.4 kg), Top Tether 65 lbs (29.5 kg).

Diagrams show various vehicle LATCH locations: Ceiling mount, Rear Package Shelf, Pick up truck, Vehicle with reinforced seats, Floor Mounts.

5.0 Installation and Use

WARNING! DEATH or SERIOUS INJURY can occur:

• Use only in a rear-facing position for infants weighing less than 22 lbs (9 kg).
• Weight/Height/Age Limits:
• Rear Facing (without upper seatback): 5 - 22 lbs.
• Rear Facing (with upper seatback): 5 - 40 lbs (2.3 - 18.1 kg).
• Forward Facing (1 year old minimum): 23 - 65 lbs (10.43 - 29 kg), height 50 inches (127 cm) or less.
• Snugly adjust the harness straps. You should not be able to pinch webbing once buckled.
• Secure the top anchorage strap.
• Secure the seat using the vehicle's LATCH system or seat belt.
• Follow all instructions on the seat and in this manual. Call 1-800-328-7363 for instructions if needed.
• Use the vehicle seat belt (not LATCH) for children weighing more than 45 lbs (20.5 kg).
• Register your child restraint with Baby Trend.
• DO NOT place a rear-facing seat in a front seat with an active airbag.
• NEVER leave a child unattended.

5.1 Child Placement in Restraint

1. Place child with back flat against the seat back and bottom touching the seat.
2. Place harness straps over the child's shoulders. Check strap height relative to shoulders.
3. For rear facing, place 5-point crotch buckle in the rear position. For forward facing, place in the forward position.
4. Insert buckle tongues into the buckle. Pull up to ensure they are secure.
5. Place chest clip at armpit level. Press tabs together. Pull outward to ensure it is secure.
6. Pull the harness adjuster to tighten straps. A snug strap should not allow slack and should lie straight without sagging.

Diagrams illustrate routing paths for forward-facing installation (lap belt with top tether, lap/shoulder belt with top tether, LATCH lower anchor with top tether) and child placement steps.

5.2 Rear Facing Installation with Lap/Shoulder Belt

Requirements: See section 2.1 (Weight 5-22 lbs, top of head not at max height line).

Diagrams show routing paths for rear-facing installation with or without headrest, using lap belt, lap/shoulder belt, or lower anchor.

WARNING: Never use a Top Tether connector in a rear-facing installation!

The seat was designed with a removable upper seatback for proper installation when it contacts the front seat. If contact prevents a 45-degree installation, remove the upper seatback. Refer to section 5.13 for removal instructions.

Reinstall the upper seat back when the child reaches 22 lbs (9.98 kg), or the top of their head has NOT reached the max height red line. Keep the child rear-facing as long as possible. Contact Baby Trend Customer Service at 1-800-328-7363 for questions.

Installation Steps (with Headrest):

1. Adjust the recline foot to the recline position. This angles the restraint to keep the baby's head back and airway open.
2. Place restraint in a rear seating position and ensure the vehicle is level.
3. Unsnap the 2 front and 2 side snaps. Lift and fold back padding.
4. Route lap/shoulder belt through the rear-facing safety belt path. Ensure webbing is flat and not twisted.
5. Apply weight to the seat cushion, insert the buckle tongue, and pull the seat belt tight. Pull up on the buckle to ensure security.
6. Lower flap and secure hook-and-loop fasteners and snaps.
7. Ensure the angle indicator line is level with the ground to keep the child's airway open.
8. Check for restraint movement at the belt path. It should not move more than 1 inch in any direction. Repeat steps if necessary.

5.3 Rear Facing Installation with Lap Belt

Requirements: See section 2.1 (Weight 5-22 lbs, top of head not at max height line).

Diagrams show routing paths for rear-facing installation with or without headrest, using lap belt, lap/shoulder belt, or lower anchor.

WARNING: Never use a Top Tether connector in a rear-facing installation!

(Instructions are similar to 5.2, adapted for lap belt only.)

Installation Steps (with Headrest):

1. Always adjust the recline foot to the recline position.
2. Place restraint in a rear seating position and ensure vehicle is level.
3. Unsnap the 2 front and 2 side snaps. Lift and fold back padding.
4. Route lap belt through the rear-facing safety belt path. Ensure webbing is flat and not twisted.
5. Apply weight to the seat cushion, insert the buckle tongue, and pull the seat belt tight. Pull up on the buckle to ensure security.
6. Lower flap and secure hook-and-loop fasteners and snaps.
7. Ensure the angle indicator line is level with the ground.
8. Check for restraint movement (should not exceed 1 inch). Repeat steps if necessary.

5.4 Rear Facing Installation with LATCH Lower Anchor

Requirements: See section 2.1 (Weight 5-22 lbs, top of head not at max height line).

WARNING: Never use a Top Tether connector in a rear-facing installation!

(Instructions are similar to 5.2, adapted for LATCH lower anchor.)

Installation Steps (with Headrest):

1. Always adjust the recline foot to the recline position. A rolled towel or pool noodle can be used for extra elevation/angle adjustment.
2. Place restraint in a rear seating position and ensure vehicle is level.
3. Unsnap the 2 front and 2 side snaps. Lift and fold back padding.
4. Route LATCH belt through the rear-facing safety belt path. Ensure webbing is flat and not twisted.
5. Apply weight to the seat cushion, insert the lower anchor connector onto the vehicle anchor point. Tighten by pulling the webbing end. Pull up to ensure secure fastening.
6. Lower flap and secure hook-and-loop fasteners and snaps.
7. Ensure the angle indicator line is level with the ground.
8. Check for restraint movement (should not exceed 1 inch). Repeat steps if necessary.

5.5 Forward Facing Installation with Lap/Shoulder Belt and Top Tether

Requirements: See section 2.3 (Weight 23-65 lbs, height 50 inches or less, age 1 year old).

1. Place restraint in a rear seating position. Adjust recline foot to the upright position for forward facing.
2. Ensure vehicle is level and the Convertible is placed flat, resting on the front outer edge of the vehicle seat.
3. Lift back flap and place harness to the side.
4. Route lap/shoulder belt through the forward-facing belt path.
5. Apply weight to the seat cushion, insert the buckle tongue, and adjust seat belt as tight as possible. Pull up on the buckle tongue to ensure security.
6. Lower flap and secure hook-and-loop fasteners.
7. Attach Top Tether to a designated anchor point. Pull Top Tether strap until snug. Consult your vehicle owner's manual for anchor locations and weight limits.
8. Check for restraint movement (should not exceed 1 inch). Repeat steps if necessary.

5.6 Forward Facing Installation with Lap Belt and Top Tether

Requirements: See section 2.3 (Weight 23-65 lbs, height 50 inches or less, age 1 year old).

1. Place restraint in a rear seating position. Adjust recline foot to the upright position for forward facing.
2. Ensure vehicle is level and the Convertible is placed flat, resting on the front outer edge of the vehicle seat.
3. Lift back flap and place harness to the side.
4. Route lap belt through the forward-facing belt path.
5. Apply weight to the seat cushion, insert the buckle tongue, and adjust seat belt as tight as possible. Pull up on the buckle tongue to ensure security.
6. Lower flap and secure hook-and-loop fasteners.
7. Attach Top Tether to a designated anchor point. Pull Top Tether strap until snug. Consult your vehicle owner's manual for anchor locations and weight limits.
8. Check for restraint movement (should not exceed 1 inch). Repeat steps if necessary.

5.7 LATCH - Forward Facing Installation with Lower Anchor and Top Tether

NOTE: Use the vehicle's seat belt (not LATCH) for children weighing more than 45 lbs (20.5 kg).

Requirements: See Section 2.3 (Weight 23-45 lbs (10.43 - 20.4 kg), height 50 inches (127 cm) or less, age 1 year old).

1. Place restraint in a rear seating position designated as lower anchor compatible. Refer to your vehicle owner's manual for LATCH locations. Adjust recline foot to the upright position when forward facing.
2. Ensure vehicle is level and the Convertible is placed flat, resting on the front outer edge of the vehicle seat.
3. Lift back flap and place harness to the side.
4. Route LATCH belt through the forward-facing belt path.
5. Apply weight to the seat cushion, insert the lower anchor connector onto the vehicle anchor point. Tighten by pulling the webbing end. Pull up to ensure secure fastening.
6. Lower flap and secure hook-and-loop fasteners.
7. Attach Top Tether to a designated anchor point. Pull Top Tether strap until snug. Consult your vehicle owner's manual for anchor locations and weight limits.
8. Check for restraint movement (should not exceed 1 inch). Repeat steps if necessary.

5.8 Aircraft Installation

1. Follow the seat belt installation for use in an Aircraft.
2. Consult your airline for requirements to use this restraint.

5.9 Child Placement in Restraint

1. Place child with back flat against the seat back and bottom touching the seat.
2. Rear Facing: Harness straps should be at or below the shoulder.
3. Forward Facing: Harness straps should be at or slightly above the child's shoulder.
4. NOTE: Forward-facing occupants weighing more than 32 lbs (14.5kg) or 35 inches (88.9 cm) MUST use height position 4.
5. Place harness straps over the child's shoulders. Check that straps are just above the child's shoulders.
6. The Convertible has been safety tested with the height insert and head pillow. The height insert is needed until the child's shoulder is at or above position 1.

Diagrams illustrate child placement and strap height for rear and forward facing.

5.10 Shoulder Height Adjustment

1. Shoulder Height Positions:
• Rear Facing: Positions 1, 2, and 3.
• Forward Facing: Positions 3 and 4.
• NOTE: Forward-facing occupants weighing more than 32 lbs (14.5 kg) or 35 inches (88.9 cm) MUST use height position 4.
2. Height Adjustment: Pull harness release handles outward. Raise or lower to the appropriate position.

5.11 Crotch Buckle Position

1. Press the crotch buckle release button and move position.
2. Crotch buckle placement:
• Rear facing: Rear most position.
• Forward facing: Forward most position.

5.12 Harness Length Adjustment

Follow instructions A.1 or A.2 based on manufacture date.

1. Unhook harness straps from the metal plate and move to desired adjustment.
2. A.1 (Before 03/20/2017): Feed one harness strap connector plate through each harness strap end. Rotate the other connector plate and feed through the other strap end. Ensure straps are securely connected to both plates.
3. A.2 (On or after 03/20/2017): Feed one harness strap connector plate through each harness strap end. Ensure both straps are securely connected to the connector plate. (Only splitter plates with “Single Use Approved BT 2016” are approved for single use.)
4. Inspect harness straps for twists. Twisted straps can prevent proper tightening and adequate restraint. Pull on straps to ensure they are securely re-attached.

5.13 Upper Seat Back Removal and Installation

WARNING: The upper seat back must be installed when the child weighs more than 22 lbs (9.98 kg), or the top of the head has reached the max height red line on the seat back, or the restraint is forward facing.

1. Removal: Lift the release tab and pull up the upper seat back. NOTE: DO NOT store the upper seat back in the passenger compartment; store it securely in your trunk or garage.
2. Installation: Align the upper seat back rods and push into openings until it locks. Pull up to ensure it is locked.

5.14 Pad Removal & Laundering

Pad Removal:

1. Unfasten the 4 elastic loops on the bottom and the 8 snaps on the edge of the pad.
2. Lift the seatback flap.
3. Remove the upper seat back.
4. Unfasten 4 snaps and remove the upper seat pad.

To Launder:

1. Hand wash in cool water with mild detergent and hang to dry.
2. NOTE: DO NOT machine wash or dry in a dryer.

5.15 Pool Noodle or Rolled Towel Use

Extra Elevation: A pool noodle or rolled towel can be used for extra elevation.

1. Place the noodle or rolled towel where the seat bottom and seat back meet.

6.0 Safety

6.1 Safe Practices

For assistance with installation or use, contact:

• Baby Trend: Phone 1-800-328-7363, Email: www.babytrend.com
• Certified Child Passenger Safety (CPS) Technician: Find one at www.nhtsa.dot.gov (select "Child Passenger Safety" then "Technician Contact Locator").
• Child Seat Inspections: www.nhtsa.dot.gov (select "Child Seat Inspections").
• www.seatcheck.org
• Car seat check-up events: Call 1-866-SEAT CHECK (1-866-732-8243).

EVERYONE rides buckled up or the vehicle DOES NOT GO! Make NO EXCEPTIONS.

• If someone unbuckles, the vehicle STOPS. Be firm and consistent.
• NEVER try to tend to a crying child while driving. Never take a child out of the restraint for comforting while the vehicle is moving.
• DO NOT allow a child to slide down under the lap belt or put the shoulder belt under their arm or behind their back.
• DO NOT allow a child to have lollipops, popsicles, or other food on a stick, as it can cause injury in a crash.
• DO NOT put heavy or sharp items in the trunk; loose items can be deadly in a crash.
• If using a blanket in cold weather, place the child in the restraint and cover both with the blanket.

6.2 Safety Checklist

• ✔ Did you read and understand these instructions and labels?
• ✔ Is the child the proper weight and height for the seat in the rear-facing position?
• ✔ If rear-facing, are the shoulder straps at or below the child's shoulders?
• ✔ Have you checked the proper seat angle for rear-facing?
• ✔ If the child is over 22 lbs, have you reinstalled the headrest?
• ✔ If the child's head is within 1" of the headrest and rear-facing, have you reinstalled the upper seat back?
• ✔ If forward-facing, have you reinstalled the upper seat back?
• ✔ Is the child the proper weight and height for the seat in the forward-facing position?
• ✔ If forward-facing, are the shoulder straps at or above the child's shoulders?
• ✔ Did you pull the harness adjuster tight? You should not be able to pinch the harness.
• ✔ Is the child restraint buckled using the LATCH system or the auto safety belt system?
• ✔ Will you discontinue use after 7 years from the manufacture date?
• ✔ Has the airbag been deactivated in a vehicle with a front-only seat?

Please Drive Safely

7.0 Additional Information

7.1 Certification

This child restraint system conforms to all applicable Federal Motor Vehicle Safety Standards for use in motor vehicles. This Convertible Seat is certified for use in motor vehicles.

7.2 Aircraft Use

1. Follow the vehicle lap belt installation for use in an Aircraft.
2. Consult your airline for requirements to use this restraint.

7.3 Vehicle Seat Protection

Protect your vehicle seat. Use a thin car seat mat, thin towel, or thin blanket under and behind the Convertible Seat.

7.4 Instruction Manual Storage

Store instruction manual in the pocket on the side of the Convertible Seat.

7.5 Convertible Seat Useful Life

DO NOT use this Convertible Seat after the date on the back of the seat. Parts may be missing, damaged, or the Convertible Seat may have been in a crash.

8.0 Registration Information

REGISTER YOUR CAR SEAT

Please complete the following information. The model number and manufactured date can be found on a label on the bottom of the Car Seat.

• Model Number: ___________________
• Manufactured in: __________________
• Purchase Date: ___________________

Please fill out the prepaid registration post card attached to the harness straps and mail it today.

Child restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall. Send your name, address, e-mail address (if available), and the restraint's model number and manufacturing date to: Baby Trend®, Inc., 1607 S. Campus Avenue, Ontario, CA 91761 or call 1-800-328-7363 or register online at: http://www.babytrend.com/registration.html. For recall information, call the U.S. Government's Vehicle Safety Hot line at 1-888-327-4236 (TTY: 1-800-424-9153), or go to http://www.NHTSA.gov.

If You Need Help

Please contact our Customer Service Department with any questions. When contacting us, please have the model and manufactured date ready. This information can be found on a white label on the bottom of the car seat.

USA Toll Free: 1-800-328-7363

Hours: 8:00 a.m. to 4:30 p.m. (PST) Monday - Friday

Website: www.babytrend.com

9.0 Care and Cleaning

9.1 Removing Seat Pad, Back Pad and Headrest Pad

Follow directions in section 5.13.

9.2 Cleaning Seat Pad, Head Bolster and Height Insert

• Hand wash in cool water with mild soap.
• Air dry.

9.3 Cleaning Shell

• Wipe with mild solution of soap and water. Avoid wetting labels.
• Rinse with clean water.
• Never use "household" detergents or solvents.

9.4 Replacement Parts

If You Need Help or Replacement Parts, please call our Customer Service Department at 1-800-328-7363 (Monday through Friday, 8:00 am - 4:30 PM Pacific Time) or visit us online at www.babytrend.com.

US PATENTS 7 901 003 AND 8 096 613. OTHER US AND FOREIGN PATENTS PENDING.