Manuals+

Baby Trend Trooper™ 3-in-1 Convertible Car Seat

Owner's Manual

For instructions in Spanish, visit www.babytrend.com or call 1-800-328-7363.

Model Number: CV01XXXB/S

AWARNING!

Carefully read and understand all instructions and warnings in this manual. Failure to properly use this Car Seat increases the risk of SERIOUS INJURY or DEATH in a sudden stop or crash.

KEEP INSTRUCTIONS FOR FUTURE USE.

Store this manual in the pocket provided on the side of the car seat base or on the underside of the seat cover.

Scan QR Code for Trooper™ how-to videos ?.

1.0 General Warnings and Information

DEATH or SERIOUS INJURY can occur:

  • Failure to follow these instructions and car seat labels can result in injury or death to a child from striking the vehicle's interior during a sudden stop or crash.
  • Even if the car seat seems easy to use, it is important to read these instructions and the vehicle owner's manual for details.
  • Follow both this manual and your vehicle owner's manual carefully. If there is a conflict, the vehicle owner's manual takes precedence regarding the vehicle's seat belt, LATCH, or airbags.
  • Failure to use the vehicle seat belt or adjust it properly can result in serious injury or death.
  • DO NOT allow others to use this car seat unless they read and understand the instructions and labels and can demonstrate proper use.
  • Use only Baby Trend® car seat accessories. Other accessories may affect your child's safety.
  • DO NOT modify or attach any toys, seat fabric, or other items to this car seat. Untested modifications could result in injury.
  • Secure this car seat with the vehicle seat belt or LATCH Lower anchor connectors at all times, even when empty. An unsecured car seat can injure others in a crash.
  • Direct sunlight can make car seat surfaces hot. Use caution on hot, sunny days.
  • NEVER leave a child unattended.
  • DO NOT use this car seat if it has been in a crash, as it may have hidden damage and must be replaced.
  • DO NOT use this car seat if it is damaged or has missing parts.
  • STOP USING THIS car seat AND PROPERLY DISPOSE after the date on the back of the seat. Dispose in a dark trash bag; DO NOT sell at thrift shops or garage sales.
  • NEVER use this car seat in homes, on boats, in motor homes, low speed vehicles, golf carts, or all-terrain vehicles. Only use in Vehicles and Aircraft.
  • NEVER use this car seat in a vehicle seating position equipped with an active air bag. Refer to your vehicle's owner's manual for information on turning off airbags or child seating in the front seat.

The National Highway Traffic Safety Administration (NHTSA) recommends children remain rear-facing until age 3 or they reach the manufacturer's height/weight limit.

2.0 Use Recommendations

Baby Trend recommends children remain in a rear-facing car seat as long as possible, until they reach the highest weight or height allowed by the seat.

2.1 Rear Facing Seat Requirements

For rear-facing use (Fig. 5a):

  • Weight: 4 to 40 lbs (1.81 to 18.1 kg)
  • Height: 40 inches (102 cm) or less
  • Top of head has NOT reached 1 inch from the top of the seatback (Fig. 5b).

Child MUST meet ALL these requirements for rear-facing use.

[Diagram showing rear-facing car seat position and head clearance measurement]

2.2 Forward Facing Seat Requirements

For forward-facing use:

  • Weight: 30 to 65 lbs (13.6 to 29.5 kg)
  • Height: 50 inches (127 cm) or less
  • Age: 2 years old
  • Top of the child's ears must be at or below the top of the car seat (Fig. 6a).

Child MUST meet ALL these requirements for forward-facing use.

Baby Trend recommends remaining rear-facing until at least 2 years old. Use of the top tether is required for installation if the vehicle is equipped with a tether anchor.

[Diagram showing ear height relative to car seat]

3.0 Car Seat Parts

Key components of the car seat include:

  • Head pillow
  • Harness
  • Body insert
  • Webbing Twist Indicator Stripe
  • Cup holders
  • Harness Covers
  • Seat pad
  • Chest clip
  • 5-point harness buckle
  • Harness tension adjuster
  • Lower anchor connectors
  • Top Tether

[Diagram illustrating the various parts of the car seat, including harness slots, splitter plate, and belt paths]

4.0 Selecting a Vehicle Seating Location

DEATH or SERIOUS INJURY can occur:

IMPROPER PLACEMENT OF THE CAR SEAT INCREASES THE RISK OF SERIOUS INJURY OR DEATH.

Not all vehicle locations are safe for car seat installation. The car seat must be tightly secured at all times. Consult your vehicle owner's manual if you are uncertain about proper location or installation.

According to accident statistics, children are safer in rear seating positions.

Preferred Location: Secure the car seat in the rear center seating position. Avoid the third row rear seat.

Forward Facing Only: DO NOT place this car seat in any seat that faces the rear or to the side.

Supervision: If possible, have an adult ride in the rear with the child for monitoring.

LATCH System: LATCH may not be available in the center rear seat position. Use the vehicle seat belt if LATCH is not available.

Front Seat Use: Only use a front seating position if there is no passenger side Active Frontal Air bag, and the child requires constant monitoring. Slide the vehicle seat as far back as possible to prevent contact with the dash in a crash.

DO NOT place a rear-facing child seat on a front seat with an active frontal air bag. The back seat is the safest place for children 12 and under.

Seatback Stability: DO NOT use in a vehicle with a seatback that does not lock into place. A folding seatback must have a latch or locking mechanism to prevent forward movement in a crash.

Vehicle Seat Belt Requirements: The car seat MUST be tightly secured by the vehicle seat belt at all times. Some vehicle seat belt systems are NOT safe for use with this car seat. Consult your vehicle owner's manual or manufacturer if unsure.

Safe Vehicle Seat Belt Systems: The following systems CAN BE USED:

  • Lap Belts (Manually Adjusted)
  • Lap Belts with Automatic Locking Retractor (ALR)
  • Combination Lap/Shoulder Belt with Locking Latch Plate
  • Combination Lap/Shoulder Belt with Sliding Latch Plate (requires locked retractor or locking clip)

Unsafe Vehicle Seat Belt Systems: DO NOT use the following systems:

  • Lap Belts with Emergency Locking Retractor (ELR)
  • Combination Lap/Shoulder Belt with Retractor (both lap and shoulder belts have retractors)
  • Passive Restraint – Lap or Shoulder Belt Mounted on Door
  • Passive Restraint – Lap Belt with Motorized Shoulder Belt
  • Lap Belts Forward of Seat Crease

Locking Clip: A locking clip may be needed for certain seat belt systems. Contact Baby Trend at 1-800-328-7363 to obtain a locking clip.

[Diagrams illustrating safe and unsafe seat belt types and locking clip installation]

4.6 Preparation for Installation in Vehicle

LATCH is the recommended method of securing the car seat when available.

FAILURE TO PROPERLY SECURE THE CAR SEAT INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN A CRASH.

Children under 13 are safer in rear seating positions.

  1. Park your vehicle on a level surface. Ensure the Seat Angle Indicator properly shows the recline angle.
  2. Select an acceptable location as instructed in Section 4.0.
  3. Check for active frontal air bags.
  4. If using a front seat, slide the vehicle seat back as far as possible. If using a rear seat, slide the vehicle seat forward to prevent the car seat from striking the seatback in a crash.

4.7 Preparation for Installation with LATCH

Consult your vehicle owner's manual for LATCH anchor point locations and availability.

4.8 LATCH - Top Tether Anchor Locations

Top Tether anchor locations are indicated by a specific symbol.

Baby Trend requires the use of the top tether if your vehicle is equipped with one. Refer to your vehicle owner's manual for locations.

Consult your vehicle owner's manual for exact LATCH locations, anchor identification, and usage requirements.

Maximum Child Weight for LATCH: 55 lbs (24.94 kg).

[Diagrams showing examples of top tether anchor locations: Ceiling mount, Rear Package Shelf, Pick up truck, Vehicle with reinforced seats, Floor Mounts]

5.0 Installation and Use

Top Tether Weight Limit: 65 lbs (29.48 kg).

DEATH or SERIOUS INJURY can occur:

Baby Trend recommends children remain rear-facing as long as possible.

  • Rear Facing: Use with infants weighing less than 30 lbs (13.6 kg).
  • General Use: 4-65 lbs (1.81-29.48 kg), Height 50 inches (127 cm) or less.
  • Forward Facing: Age 2 years, 30-65 lbs (13.6-29.5 kg).
  • Harness Adjustment: Adjust straps snugly so you cannot pinch webbing.
  • Secure the top anchorage strap.
  • Secure the child seat using the vehicle's LATCH system or a lap/shoulder belt.
  • Call 1-800-328-7363 for instructions if needed.
  • Use vehicle seat belt (not LATCH) for children weighing more than 55 lbs (24.9 kg).
  • Register your car seat with Baby Trend.
  • DO NOT place a rear-facing child seat in a front seat with an active airbag.
  • NEVER leave a child unattended.

5.1 Child Placement in The Car Seat

  1. Place child with back flat against the seatback and bottom touching the seat.
  2. Rear Facing: Harness straps should be at or below the child's shoulders.
  3. Forward Facing: Harness straps should be at or slightly above the child's shoulders. Use slots 3, 4, and 5 for forward facing.
  4. Place harness straps over the child's shoulders.
  5. Insert buckle tongues into the crotch buckle. Pull up and test to ensure they are secure.
  6. Place chest clip at armpit level. Press together and pull outward to ensure it is secure.
  7. Pull the harness adjuster to tighten straps. The strap should be snug, with no slack, and lie in a straight line without sagging. It should not press into the child's skin or push the body unnaturally.

[Diagrams showing child placement and correct harness strap height for rear and forward facing positions, including insert and pillow usage notes]

5.1.1 Installation Diagrams

Routing paths for Rear Facing installation:

  • Lap belt
  • Lap/Shoulder belt
  • Lower anchor (LATCH)

Routing paths for Forward Facing installation:

  • Lap belt with top tether
  • Lap/Shoulder belt with top tether
  • Latch Lower anchor with top tether

Use of the top tether is required if the vehicle has a tether anchor.

Never use a Top Tether connector in a rear facing installation!

5.2 Rear Facing Installation with Lap/Shoulder Belt

Requirements: Weight 4-40 lbs (1.81-18.1 kg), Height 40 inches (102 cm) or less, Top of head not reached 1" from seatback.

  1. Adjust the recline foot to the recline position for rear facing. This helps keep the baby's head back and airway open.
  2. Park on level ground, place the car seat in a rear seating position, and ensure the vehicle is level.
  3. Route the Lap/Shoulder Belt through the rear facing belt paths and under the seat fabric. Ensure webbing is flat and free of twists before securing.

[Diagram showing lap/shoulder belt routing for rear-facing installation]

5.3 Rear Facing Installation with Lap Belt

Requirements: Weight 4-40 lbs (1.81-18.1kg), Height 40 inches (102 cm) or less, Top of head has NOT reached 1" from seatback.

  1. Adjust the recline foot to the recline position for rear facing.
  2. Park on level ground, place the car seat in a rear seating position, and ensure the vehicle is level.
  3. Route the Lap Belt through the rear facing belt paths and under the seat fabric. Ensure webbing is flat and free of twists before securing.

Securing the Belt: Use body weight to compress the seat cushion, insert the buckle tongue, and pull the seat belt tight. Pull up on the buckle to ensure it is secure. Refer to your vehicle manual for lockable retractors.

Angle Indicator: Ensure the angle indicator bubble is centered for children 4-22 lbs (1.81-9.97 kg) to keep the airway open. Ensure the angle indicator line is level with the ground for children 23-40 lbs (10.43-18.14 kg).

Check for Movement: The car seat should not move more than 1 inch in any direction at the safety belt path. Repeat steps if necessary.

[Diagrams showing angle indicator bubble and line]

5.4 Rear Facing Installation with LATCH Lower Anchors

Requirements: Weight 4-40 lbs (1.81-18.1kg), Height 40 inches (102 cm) or less, Top of head has NOT reached 1" from seatback.

Place the car seat in a LATCH Lower Anchor compatible rear seating position. Refer to your vehicle owner's manual for LATCH locations.

  1. Adjust the recline foot to the recline position for rear facing.
  2. Park on level ground, place the car seat in a rear seating position, and ensure the vehicle is level.
  3. Route LATCH Lower Anchors through the rear facing belt paths and under the seat fabric. Ensure webbing is flat and free of twists before securing.

Securing the Anchors: Use body weight to compress the seat cushion, insert the lower anchor connector onto the vehicle anchor point, and tighten by pulling up on the webbing end. Ensure the lower anchor is securely fastened.

Angle Indicator: Ensure the angle indicator bubble is centered for children 4-22 lbs (1.81-9.97 kg) to keep the airway open. Ensure the angle indicator line is level with the ground for children 23-40 lbs (10.43-18.14 kg).

Check for Movement: The car seat should not move more than 1 inch in any direction at the safety belt path. Repeat steps if necessary.

[Diagrams showing LATCH anchor routing and angle indicator]

5.5 Forward Facing Installation with Lap/Shoulder Belt and Top Tether

Requirements: Weight 30 to 65 lb (13.6 to 29.5 kg), Height 50 inches (127 cm) or less, Age 2 years old.

  1. Place the car seat in a rear seating position. Adjust the recline foot to the upright position for forward facing.
  2. Ensure the vehicle is level and the car seat is placed flat on the front outer edge of the vehicle seat.
  3. Loosen harness by pressing the adjuster and pulling on harness. Pull top of seat fabric down to expose the forward facing belt path. Ensure webbing is free of twists.

[Diagram showing forward-facing installation with lap/shoulder belt and top tether]

5.6 Forward Facing Installation with Lap Belt and Top Tether

Requirements: Weight 30 to 65 lb (13.6 to 29.5 kg), Height 50 inches (127 cm) or less, Age 2 years old.

  1. Place the car seat in a rear seating position. Adjust the recline foot to the upright position for forward facing.
  2. Ensure the vehicle is level and the car seat is placed flat on the front outer edge of the vehicle seat.
  3. Loosen harness by pressing the adjuster and pulling on harness. Pull top of seat fabric down to expose the forward facing belt path. Ensure webbing is free of twists.
  4. Route seat belt through forward facing belt path.
  5. Use body weight to compress the seat cushion, insert the buckle tongue, and adjust seat belt as tight as possible.
  6. Pull seat fabric up and over the car seat. Install the pillow if applicable.
  7. Pull up on buckle to ensure it is secure. Refer to your vehicle manual for lockable retractors.
  8. Attach Top Tether to a designated anchor point. Pull Top Tether strap until snug.
  9. Check for movement (< 1 inch). Repeat steps if necessary.

[Diagrams illustrating forward-facing installation steps with lap belt and top tether]

5.7 LATCH - Forward Facing Installation with Lower Anchor and Top Tether

Requirements: Weight 30 to 65 lb (13.6 to 29.5 kg), Height 50 inches (127 cm) or less, Age 2 years old.

DO NOT use this method for a child weighing more than 55 lbs (24.9 kg).

  1. Place the car seat in a rear seating position. Adjust the recline foot to the upright position for forward facing.
  2. Ensure the vehicle is level and the car seat is placed flat on the front outer edge of the vehicle seat.
  3. Loosen harness by pressing the adjuster and pulling on harness. Pull top of seat fabric down to expose the forward facing belt path.
  4. Route lower anchors through forward facing belt path.
  5. Use body weight to compress the seat cushion, insert the lower anchor connector onto the vehicle anchor point, and tighten by pulling up on the webbing end. Ensure the lower anchor is securely fastened.
  6. Pull seat fabric up and over the car seat. Install the pillow if applicable.
  7. Attach Top Tether to a designated anchor point. Pull Top Tether strap until snug.
  8. Check for movement (< 1 inch). Repeat steps if necessary.

[Diagrams illustrating forward-facing installation steps with LATCH lower anchors and top tether]

5.8 Aircraft Installation

Follow the seat belt installation procedures for use in an aircraft. Consult your airline for specific requirements.

5.9 Child Placement In The Car Seat

  1. Place child with back flat against the seatback and bottom touching the seat.
  2. Rear Facing: Harness straps should be at or below the child's shoulders.
  3. Forward Facing: Harness straps should be at or slightly above the child's shoulders. Use slots 3, 4, and 5 for forward facing.
  4. Place harness straps over the child's shoulders.
  5. The car seat has been safety tested with the insert and pillow. DO NOT use the pillow if the child's head falls forward.

Pillow Use: For forward-facing use only. DO NOT use in the Low Birth Weight Harness Routing option. DO NOT use Pillow and Harness in the same harness slot. Discontinue use when the child requires harness position 5.

Insert Use: Not mandatory. MAY be used in the Low Birth Weight Harness Routing option. ONLY use the insert with children weighing between 4-18 lbs (1.81-8.16 kg). Rear facing use only.

[Diagrams showing child placement and harness strap height adjustments]

5.10 Shoulder Height Adjustment

Shoulder Height Positions:

  • Rear Facing: Positions 1, 2, and 3.
  • Forward Facing: Positions 3, 4, and 5.

Height Adjustment:

  1. Loosen harness, unfasten harness end loops from the splitter plate. Pull harness end loops through the seatback. Thread harness end loops through the desired shoulder position.
  2. Fasten harness end loop to the splitter plate. Ensure both sides are threaded in the same position.

[Diagrams showing shoulder height adjustment positions and threading]

5.11 Crotch Buckle Adjustment

The crotch strap length should be adjusted so there is a gap of 1/2" to 1" between the ears of the buckle and the top of the child's thigh.

To Adjust: To shorten the buckle webbing, place the anchor bracket through the slot in front or rear of the buckle.

[Diagrams showing crotch buckle adjustment and gap measurement]

5.12 Seat Fabric Removal And Laundering

Seat Fabric Removal:

  1. Unfasten harness end loops from the metal plate and pull harness through the seatback. Unbuckle the crotch buckle and chest clip.
  2. Pull up and out on the seat fabric, feeding the harness, buckle tongues, and chest clip through the slots on the seat fabric.
  3. Slip seat fabric over the cup holders.

Cleaning:

  • Use only mild soap or detergent and warm water on a sponge or clean cloth.
  • Do Not machine wash.
  • Do Not dry clean.
  • Do Not bleach.
  • Do Not iron.

[Diagrams showing seat fabric removal steps]

5.13 Low Birth Weight Harness Shortening Routing

Follow these steps for low birth weight harness routing:

  1. Remove head pillow.
  2. Remove harness loop ends from splitter plate and pull harness through the seat back.
  3. Remove harness cover, chest clip, and buckle tongue on one side. Remove cup holders.
  4. Pull harness webbing through the insert and remove the seat insert.
  5. Lift seat fabric and pull crotch buckle through.
  6. Use crotch buckle in position 1.
  7. Pull crotch buckle anchor through to position 2.
  8. Feed harness loop down through seat slot (1), then back through slot (2), then upright through slot (3). Repeat on opposite side.
  9. Pull excess webbing to equalize harness length. Ensure both sides are the same length.
  10. Place seat fabric on shell, threading harness end loops through the innermost slots.
  11. Thread buckle through seat fabric. Install seat fabric insert (use is not required).
  12. Insert buckle tongue into crotch buckle. Feed harness end loop from back of buckle tongues.
  13. Feed chest clip through harness end loops.
  14. Pull up on webbing end loops to equalize them.
  15. Feed harness end loops and crotch buckle through appropriate slots on seat insert.
  16. Thread harness end loops through appropriate slot No. 1 or 2. Shoulder slots must be at or below child's shoulder.
  17. Thread loop number 1 through splitter plate.
  18. DO NOT use harness covers with Low Birth Weight Routing.
  19. DO NOT use pillow with Low Birth Weight Routing.
  20. Place child in seat and confirm harness is at or below child's shoulder.

[Diagrams illustrating low birth weight harness routing steps and slot numbering]

5.14 Pillow, Insert and Harness Covers Use

  • Pillow Use: Not mandatory. DO NOT use in Low Birth Weight Harness Routing. DO NOT use Pillow and Harness in the same harness slot. Discontinue use when the child requires harness position 5.
  • Insert Use: Not mandatory. MAY be used in Low Birth Weight Harness Routing. ONLY use with children weighing 4-18 lbs (1.81-8.16 kg). Rear facing use only.
  • Harness Covers: DO NOT use in Low Birth Weight Harness Routing. MUST be used in all other modes.

5.15 Harness Hip and Buckle Use Positions

  • Crotch Buckle Positions: 1 & 2 (Rear Facing and Forward Facing use). The buckle should be at the crotch, not under it.
  • Harness Hip Positions: 1 (Low Birth Weight Harness Shortening Routing Only), 2 (Up to 40 lbs), 3 (Above 40 lbs). The harness should be at or out from the hip, not under it.

[Diagrams showing harness hip and crotch buckle positions]

5.16 Cup holders Removal, Installation and Cleaning

Removal: Use a Phillips screwdriver to remove the screw and washer from the bottom of the cup holder. Press the tab on the bottom of the cup holder to release it, then pull upward.

Installation: Pull back the car seat cover to expose the cup holder receptacle. Align the cup holder with the receptacle and press it into place. Secure with the screw and washer. Fit the seat cover over the cup holder.

Cleaning: Wipe with mild soap or detergent and warm water. Rinse with clean water. Never use "household" detergents.

[Diagrams showing cup holder removal and installation]

5.17 Securing Pillow

  1. Insert pillow attachment straps through the appropriate shoulder belt position.
  2. Secure attachment straps with hook and loop fasteners.

[Diagrams showing pillow attachment]

5.18 Pool Noodle or Rolled Towel Use Extra Elevation

A pool noodle or rolled towel can be used for extra elevation:

  1. Place where the seat bottom and seat back meet for additional recline elevation.
  2. Place at the back of the car seat bottom for additional incline elevation.
  3. Multiple noodles or towels may be secured together.

[Diagrams showing pool noodle/towel placement for elevation]

6.0 Safety

6.1 Safety Checklist:

  • Did you read and understand these instructions and labels? ✔️
  • Is the child the proper weight and height for the seat in the rear-facing position? ✔️
  • If rear-facing, are the shoulder straps at or below the child's shoulders? ✔️
  • Have you checked the proper seat angle for rear-facing? ✔️
  • Is the child the proper weight and height for the seat in the forward-facing position? ✔️
  • Baby Trend requires the use of the top tether if your vehicle is equipped with one. Refer to your vehicle owner's manual for locations. ✔️
  • If forward-facing, are the shoulder straps at or above the child's shoulders? ✔️
  • Did you pull the harness adjuster tight? You should not be able to pinch the harness. ✔️
  • Is the car seat buckled with either the LATCH system or the auto safety belt system? ✔️
  • Discontinue use after 7 years from the date of manufacture. ✔️
  • Has the airbag been deactivated in a vehicle with a front-only seat? ✔️

Please Drive Safely.

7.0 Additional Information

7.1 Certification

The car seat system conforms to all applicable Federal Motor Vehicle Safety Standards for use in motor vehicles.

7.2 Aircraft Use

This restraint is certified for use in aircraft.

7.3 Vehicle Seat Protection

Protect your vehicle seat. Use a thin car seat mat, towel, or blanket under and behind the car seat.

7.4 Instruction Manual Storage

Store this manual in the pocket provided on the underside of the seat cover.

7.5 Car Seat Useful Life

DO NOT use this car seat after the date on the back of the seat. Do not use if parts are missing, damaged, or if the car seat has been in a crash.

Registration Information

REGISTER YOUR CAR SEAT

Please complete the following information. The model number and manufactured date can be found on a label on the bottom of the car seat.

  • Model Number: ___________________
  • Manufactured in: __________________
  • Purchase Date: ___________________

Please fill out and mail the prepaid registration postcard attached to the harness straps.

Registering ensures you can be reached in case of a recall. Send your name, address, email, model number, and manufacturing date to: Baby Trend®, Inc, 13048 Valley Blvd. Fontana CA 92335 or register online at: https://babytrend.com/pages/car-seat-product-registration

For recall information, call the U.S. Government's Vehicle Safety Hot line at 1-888-327-4236 (TTY: 1-800-424-9153), or visit https://www.nhtsa.gov.

If You Need Help

Contact Customer Service with any questions. Have the model and manufactured date ready. USA Toll Free: 1-800-328-7363 (8:00 a.m. to 4:30 p.m. PST, Monday - Friday) or visit www.babytrend.com.

9.0 Care and Cleaning

9.1 Removing The Seat Fabric, Insert and Pillow

Follow directions in section 5.12.

9.2 Cleaning The Seat Fabric, Insert and Pillow

  • Use only mild soap or detergent and warm water on a sponge or clean cloth.
  • Do Not machine wash.
  • Do Not dry clean.
  • Do Not bleach.
  • Do Not iron.

9.3 Cleaning Car Seat Parts and Buckles

  • Wipe with mild soap and water. Avoid wetting labels.
  • Rinse with clean water.
  • Never use "household" detergents or solvents.

9.4 Replacement Parts

For help or replacement parts, call Customer Service at 1-800-328-7363 (8:00 am - 4:30 PM, Standard Time, Monday-Friday) or visit www.babytrend.com.

10.0 Warranty

Warranty (English)

DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND® FOR REPLACEMENT PARTS, SERVICE AND REPAIR.

The Baby Trend® warranty covers workmanship defects within the first 180 days of purchase. The warranty is voided by misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration, accident, or if the serial number is altered or removed. Any damage to property during installation is the sole responsibility of the end user.

Contact Customer Service at 1 (800) 328-7363 (Monday-Friday, 8:00 a.m. - 4:30 p.m. PST) for return authorizations.

Garantía (Español)

NO DEVUELVA SU PRODUCTO A LA TIENDA. POR FAVOR CONTACTE A BABY TREND® PARA PIEZAS DE REPUESTO, SERVICIO Y REPARACIÓN.

La garantía de Baby Trend® cubre defectos de fábrica dentro de los primeros 180 días de la compra. Cualquier producto sometido a uso indebido, abuso, uso anormal, desgaste excesivo, montaje incorrecto, negligencia, exposición ambiental, alteración o accidente, o con el número de serie alterado o removido, anula todos los reclamos contra el fabricante. Cualquier daño a la propiedad durante la instalación es responsabilidad exclusiva del usuario final.

Contacte al Departamento de Servicio al Cliente al 1 (800) 328-7363 (Lunes a viernes, 8:00 a.m. - 4:30 p.m. PST). Se requiere un número de autorización antes de la devolución del producto.

Garantie (Français)

NE PAS RETOURNER VOTRE PRODUIT AU MAGASIN. VEUILLEZ CONTACTER BABY TREND® POUR DES PIÈCES DE RECHANGE, ENTRETIEN ET RÉPARATION.

La garantie Baby Trend® couvre les vices de fabrication dans les 180 jours suivant l'achat. La garantie est annulée par un usage abusif, une utilisation anormale, une usure excessive, un montage incorrect, la négligence, l'exposition environnementale, la modification ou un accident, ou si le numéro de série est modifié ou supprimé. Tout dommage à la propriété lors de l'installation est de la seule responsabilité de l'utilisateur final.

Le service client peut être contacté au 1 (800) 328-7363 (du lundi au vendredi, 8 h – 16 h 30 PST). Une autorisation sera nécessaire avant de retourner le produit.

Models: CV01XXXB Convertible Car Seat, CV01XXXB, Convertible Car Seat, Car Seat, Seat

File Info : application/pdf, 28 Pages, 1.33MB

PDF preview unavailable. Download the PDF instead.

CV01XXXB S En 010925.2

References

Adobe PDF Library 17.0 Adobe InDesign 20.0 (Macintosh)

Related Documents

Preview Baby Trend Trooper SLIM 3-in-1 Convertible Car Seat Owner's Manual
This owner's manual provides comprehensive safety, installation, and usage instructions for the Baby Trend Trooper SLIM 3-in-1 Convertible Car Seat. Learn how to properly secure your child and ensure safe travel with detailed guidance from Baby Trend.
Preview Baby Trend Trooper PLUS 3-in-1 Convertible Car Seat Owner's Manual
Comprehensive owner's manual for the Baby Trend Trooper PLUS 3-in-1 Convertible Car Seat, covering installation, safety, use, and care instructions. Learn how to properly secure your child for maximum safety.
Preview Baby Trend Trooper 3-in-1 Convertible Car Seat Owner's Manual
This owner's manual provides comprehensive instructions for the Baby Trend Trooper 3-in-1 Convertible Car Seat. It covers safety warnings, use recommendations, installation procedures (rear-facing and forward-facing using seat belts or LATCH), child placement, care and cleaning, and warranty information.
Preview Baby Trend CV88 PROtect Sport Convertible Car Seat Owner's Manual
Comprehensive owner's manual for the Baby Trend CV88 PROtect Sport Convertible Car Seat, covering installation, usage, safety guidelines, care, and registration.
Preview Baby Trend PROtect Elite Convertible Car Seat Owner's Manual
Comprehensive owner's manual for the Baby Trend PROtect Elite Convertible Car Seat (Model CV88C), providing detailed instructions on installation, use, safety, and care for optimal child safety.
Preview Baby Trend Hybrid 3-in-1 Car Seat Owner's Manual
Comprehensive owner's manual for Baby Trend Hybrid PLUS and Hybrid LX 3-in-1 Car Seats. Learn about installation, safety features, use modes (Toddler, Booster), and maintenance for optimal child safety.
Preview Baby Trend FastBack 3-in-1 Car Seat Owner's Manual
Comprehensive owner's manual for the Baby Trend FastBack 3-in-1 Car Seat. Provides detailed instructions for installation, use modes (toddler, high-back booster, backless booster), safety guidelines, height and weight limitations, care, and maintenance. Includes warnings and tips for optimal child safety.
Preview Baby Trend Hybrid 3-in-1 Combination Booster Car Seat Owner's Manual
Comprehensive owner's manual for the Baby Trend Hybrid 3-in-1 Combination Booster Car Seat (Model FB49XXXB/S), providing detailed instructions for installation, use, and safety for Toddler, High-back Booster, and Backless Booster modes.