V7T Truck Dash Cam

Safety Instructions

In order to use this product safely, please confirm that you fully understand the following.

WARNING: This section indicates that mishandling can have serious consequences.

Note: This section indicates that improper handling may cause injury to the user or damage the product.

• ? [Prohibit]
• ❗ [Obey]

WARNING

• Please use this product under the premise of obeying traffic rules.
• Do not install the device in a position that blocks the view or obstructs driving.
• Do not disassemble or modify this product by yourself.
• Do not use accessories not included.
• Do not allow water to enter this product.

ATTENTION

• If the product makes an abnormal noise or smell, please stop using it immediately.
• The waterproof rating of the camera is IP67, and the host is not waterproof.
• When disposing of this product, please follow the classification principle and do not discard it at will.
• Do not store this product in a high temperature and humid environment.

Features

Replace conventional lithium batteries with super capacitors for longer life and safer.

1. HD display screen.
2. Support reversing auxiliary line.
3. Support battery voltage display.
4. Video can be recorded after inserting Micro SD card.
5. Built-in WiFi, can view real-time video on the dedicated APP.

Standard Accessories

• Host: [Diagram Description: A rectangular device with mounting brackets.]
• Front Camera: [Diagram Description: A small, round camera with a mounting bracket.]
• Rear Camera: [Diagram Description: A small, round camera, possibly designed for rear mounting.]
• Remote Control: [Diagram Description: A small remote with buttons.]
• GPS Module: [Diagram Description: A small module with a GPS antenna.]
• User Manual: [Diagram Description: A booklet.]
• Power Cable: [Diagram Description: A cable with a car cigarette lighter plug on one end and connectors for the device on the other.]

If there is any change of specification and appearance due to improvement, we are not able to inform you in advance. Please understand.

Please note that there are differences between the schematic diagram and the real object in the manual.

Description of Each Part

[Diagram Description: A diagram showing the host unit with various cables and modules connected. Numbered callouts point to different parts.]

• 1. Up Button
• 2. OK Button
• 3. Down Button
• 4. Card Slot
• 5. Reset Button
• 6. Microphone
• 7. Power Connector
• 8. GPS Connector
• 9. Camera Connector
• 10. Camera Connector
• 11. Power Cable
• 12. GPS Module
• 13. Camera
• 14. Camera

Micro SD Card

1. Please use the high-quality Class 10 or above genuine SD card.
2. The recorder supports 16G-256G memory card.
3. If the memory card cannot save the file properly, please format it on the recorder.

Formatting will delete the data, please backup the card data before performing formatting.

[Diagram Description: Two illustrations showing how to insert and remove an SD card from a slot.]

1. Insert the card into the card slot as shown in the picture.
2. When picking up the card, gently press the SD card and slowly release it after hearing "Da".
3. Please pay attention to the direction of the gold finger on the SD card. If it is inserted reversely, the SD card and recorder will be damaged.

Attention:

• The card used on other devices will be automatically formatted after being inserted into our DVR. Please back up the data.
• In the case of high frequency of use, it is recommended to format the memory card every two weeks.
• Please do not pull out the card in the recording state to avoid damaging the video file and recorder.

Specifications

Installation Guide

Please connect the yellow wire on the rear camera to the 12V positive pole of the inverted light. When the vehicle is in reverse gear, the rear camera screen will be displayed in full screen on the main unit of the recorder, with a reversing auxiliary line. It is convenient for users to observe the surrounding environment when reversing.

[Diagram Description: Illustration of a truck showing placement for Rear Camera, Host, and Front Camera.]

Host Fixed Installation Diagram

[Diagram Description: Two illustrations showing the interior of a car dashboard with the host unit mounted. Top illustration: Host mounted near the rearview mirror on the windshield. Bottom illustration: Host mounted on the center console.]

1. Hang it on the windshield.
2. Stand on the center console.

Note: You can choose to rotate 180° to adjust the screen interface in the host menu.

Power on

After installing the recorder and inserting the SD card, insert the charger into the cigarette lighter. Start the car to start recording automatically.

Attention

This recorder uses the latest supercapacitor design to replace the traditional lithium battery design; supercapacitor will automatically charge and can save the last file after disconnecting the power.

Screen Information and Menu Descriptions

Recording Mode Display

1. After selecting, press OK to enter recording mode.
2. The icon becomes larger to indicate that the function has been selected.

Description of characters on the display in recording mode:

Date&Time, Video time, Recording icon, Microphone, Altitude, GPS, Parking Monitoring, Countdown, WiFi, Lock video, Front Camera, Voltage, Speed, Atmospheric pressure.

[Diagram Description: A screenshot of the dash cam display showing various information like date, time, speed, GPS status, recording icon, microphone status, altitude, and atmospheric pressure.]

Note: When parking is detected, the recorder will turn off after the progress bar is complete, which takes about 5 minutes.

Playback Mode Display

1. After selecting, press OK to enter playback mode.
2. The icon becomes larger to indicate that the function has been selected.

1. Press [Up/Down Arrow] to select the video to playback.

"F/" indicates front camera video playback.

[Diagram Description: A screenshot showing a list of video files, with "F/" prefix indicating front camera footage.]

In playback mode, long press [Up Arrow] for 3 seconds to switch to view the list of video files saved by the front and rear cameras.

Front camera video files name identification: REC_ The year, month and time of current video F.MOV

"R/" indicates rear camera video playback.

[Diagram Description: A screenshot showing a list of video files, with "R/" prefix indicating rear camera footage.]

Rear camera video files name identification: REC_ The year, month and time of current video R.MOV

[Diagram Description: An illustration showing a reversing auxiliary line overlayed on a rear camera view.]

Menu Descriptions

Settings

1. After selecting, press OK to enter setting mode.
2. The icon becomes larger to indicate that the function has been selected.

Note: "Flameout Detection", "Parking Monitoring", "Parking Monitoring Sensitivity", and "Timed Recording after Flameout" functions are optional and require the purchase of an additional power cable. Contact customer service for these functions.

• 1. Video clip time: 1/2/3/5 minutes can be selected.
• 2. Sound record: Set whether the recorded video needs sound.
• 3. MIC sensitivity: Set the sound level of MIC.
• 4. Flameout Detection: On: After detecting that the vehicle is turned off, the recorder shutdown after waiting for about 10 seconds; Off: After 5 minutes without vibration, the recorder shutdown.
• 5. Parking Monitoring: Set whether to turn on or off parking monitoring function.
• 6. Parking Monitoring Sensitivity: Set the sensitivity of parking monitoring.
• 7. Timed Recording after Flameout: Set the time to keep recording after the vehicle is turned off.
• 8. Flip Screen: Whether the recorder display needs to be flipped at 0°/180°.
• 9. Date watermark: Whether recording video needs date watermark.
• 10. Unit system: Set the speed unit displayed when driving.
• 11. Button sound: Set the button sound on or off.
• 12. Clock setting: Set display time.
• 13. Date format: Three format options: YYYY MM DD/MM DD YY/DD MM YYYY.
• 14. Speed watermark: Whether it is necessary to turn on the driving speed display when playing videos on the computer.
• 15. Auto screen off: Set the display screen backlight to be off, or off after 1min/3min.
• 16. Protection Level: G-Sensor sensitivity level adjustment.
• 17. GPS Status: Display the current number of satellites, longitude, latitude, etc.
• 18. Time zone selection: Time zone selection around the world.
• 19. System reset: Restore to the factory default settings.
• 20. WiFi MODE: On/Off.
• 21. Format SD card: Delete all videos from the memory card.
• 22. FW version: Information about the current software version of the recorder.

Language Selection

1. After selecting, press OK to enter language selection mode.
2. The icon becomes larger to indicate that the function has been selected.

1. Language identification -- corresponding to the selected language.

2. The number of language options depends on the actual model.

Note: The specific functions are subject to the actual product received.

Mobile Phone APP Installation and Operation

WiFi APP is a mobile phone control software used with VSYSTO DVR device. This software is connected to the DVR device via Wi-Fi; it can directly preview and playback the video on the mobile phone, easily realize viewing the camera documents on the screen of mobile phone, setting or other operations. Subverting the control method of traditional cameras, bring you a new experience.

[Diagram Description: Two QR codes are displayed.]

• App download for Android user: [QR Code for Android App Download]
• App download for Apple user: [QR Code for Apple App Download]

Scan the QR code above to download the latest APP from Google Play and APP Store. Or you can search "WiFi Camera" on Google Play or APP Store to download and install it.

Conditions of use and product association:

1. Smart terminal with Android 5.0 or higher or Apple terminal.
2. Purchase a compatible device that uses VSYSTO design scheme, and connect the mobile phone WiFi to the camera correctly.

DVR WiFi Default Name: DV-V7T-XXXX

Default password: 1234567890

Note: To ensure the normal use of APP functions, please update the APP to the latest version in time.

Live Preview (Video / Photo)

After connecting the camera WiFi with mobile phone, open the APP and click [Connect Device Button] to enter video preview status. In video preview state, you can control the camera to take video or photo. Click [Camera Switch Icon] to switch front/rear image. Click [Full Screen Icon] to full screen display (as shown in the figure below).

[Diagram Description: A screenshot of the mobile app's live preview screen, showing recording controls and camera feed.]

Browse Recorder Files

Click [Online Tab Icon] to browse the video files on the recorder memory card (as shown in the figure below).

[Diagram Description: A screenshot of the mobile app's file browsing interface, showing tabs for Device, Online, Local, Settings.]

Playback Recorder Files

Browsing the recorder file interface in the "Online" option, click the file you want to playback. Click the upper left corner [Camera Switch Icon] to switch the front/rear camera file, F means the front camera, R means the rear camera.

Download or Delete Recorder Files

In the "Online" browsing recorder file interface, click [EDIT Button] to select the file you want to download or delete, and then click [Save Button] or [Delete Button] below as needed (as shown in the figure below).

[Diagram Description: Screenshots showing the file list in the mobile app, with options to edit, save, or delete files.]

Video File Name:

• REC-XXXX— Normal recorded videos
• GSR-XXXX— Emergency recorded videos

Note: The recorder will lock the last 10 emergency recorded videos (GSR-XXXX) that are not overwritten by the normal recorded videos. If there are more than 10 GSR-XXXX files, it will automatically overwrite the earliest locked emergency recorded videos.

Local Files Management

Click [Local Tab Icon] to enter the browsing interface of local files to replay/delete the files stored in the mobile phone, and the operation is similar to the online interface.

[Diagram Description: A screenshot of the mobile app's file browsing interface, showing tabs for Device, Online, Local, Settings.]

Recorder Parameter Setting

Click [Settings Icon] to enter the recorder parameter setting interface, and you can set some parameters of the recorder in the mobile APP.

Set SSID is the WiFi name and password for setting the recorder (as shown in the picture below).

[Diagram Description: A screenshot of the mobile app's settings menu, showing options like Looping Video, Sound Record, GST, Reset Camera, Format SD Card, Set SSID, etc.]

If you need to view the video track, you can save the downloaded video in the Local of APP. Then switch the phone to a network that can access the Internet, click to play the video, and the track of your driving will be displayed below the video. The default map of the APP is Baidu Map. If you need Google Map, please change Baidu Map to Google Map in the APP settings interface.

Note: When you play a video on the mobile APP to view the driving track, you can only view the video of a single camera (front/rear), and cannot play multiple cameras at the same time.

[Diagram Description: Screenshots showing a video playback with a map overlay displaying a driving route.]

Wireless Remote Control

1. Short press the red button once to switch to the full screen of the rear camera.
2. Short press the blue button once to switch the full screen of the front camera.
3. Double-clicking either of the two buttons will trigger emergency lock mode. The front and rear cameras start recording emergency video, while capturing a picture. While recording an emergency video, double-clicking the button again cannot trigger lock mode repeatedly. Only when the last emergency video recording is completed, double-clicking again can trigger. The video file name is named after KEY-XXXXX. The locked video will not be overwritten by the normal recorded "REC-XXXXX" file. When the SD card video file exceeds 10 KEY-XXXXX videos, the system will delete the earliest KEY-XXXXX emergency video.

Battery Replacement Guide

Model: CR2032

[Diagram Description: Three illustrations showing the process of replacing the battery in the remote control.]

1. Use a screwdriver to remove the 4 screws at the bottom of the remote control, and then lift off the protective cover.
2. Push the coin cell battery out of the side with a screwdriver or fingernail.
3. Install the new battery into the battery base according to the positive and negative poles. After ensuring that it can be used normally, close the protective cover and screw back the screws.

GVP Operation Guide (Optional)

Operating Systems Supported by GVP WinXP/7/8/10 Installed Version

Double-click setup.exe to start the installation. After the installation is complete, the desktop and start menu automatically generate shortcuts.

[Diagram Description: A table showing installation files like vcredist_x86.exe, GvpSetup.nsi, setup.exe.]

Double-click the desktop shortcut icon [Desktop Shortcut Icon] or click the start menu to select the corresponding option of GVP [GVP Application Icon] to open the software.

Green Version

[Diagram Description: A list of files like plugins, GVP.exe, Gvp.ini, libvlc.dll.]

Double-click [Software Interface Icon] to open the software interface.

Interface Picture Example

Initial Interface

When the mouse moves to the corresponding icon, there will be an operation prompt, please follow the prompt to operate (as shown in the figure below).

[Diagram Description: A screenshot of the GVP software's initial interface with various icons.]

Interface during Playback

During playback, double-click the front camera or rear camera image, the full screen of the camera will be displayed. Double-click again to exit full screen.

[Diagram Description: A screenshot of the GVP software during video playback.]

Playback Interface Supports Multiple Languages and Google Maps

Click [Settings Icon] to set the player language and map.

Note: If GV Player cannot be used, you can use DV Player or other software that is compatible with recorded videos.