Storage Box Instruction Manual
Introduction
This manual provides detailed instructions for the assembly and installation of your Storage Box system. Please read all instructions carefully before beginning.
Parts List
| Item No. | Description | Quantity |
|---|---|---|
| 1 | Top Panel / Shelf | 1 |
| 2 | Left Side Panel | 1 |
| 3 | Right Side Panel | 1 |
| 4 | Shelf | 4 |
| 5 | Shelf | 2 |
| 6 | Bottom Panel / Shelf | 1 |
| 7 | Left Side Panel | 1 |
| 8 | Right Side Panel | 1 |
Visual representation: The parts list shows various rectangular panels and shelves, labeled with numbers 1 through 8. Parts 2, 3, 7, and 8 are taller side panels, while parts 1, 4, 5, and 6 are shorter shelf/panel pieces.
Hardware Usage Guide
How to Use a Cam Lock & Cam Bolt
Cam Bolt Usage: Turn the Cam Bolt until its shoulder is against the surface of the part.
Cam Lock Usage: Push a Cam Lock into the part. The arrow on the Cam Lock must point towards the hole in the edge of the board.
Assembly: Insert the Cam Bolt into the Cam Lock and tighten the Cam Lock.
Finishing: Remove the protective layer of sticker and use it to cover all cam-lock holes and bolt holes that are visible.
Tools Required
- Tape Measure
- Pencil
- Power Drill with 3mm (1/8 inch) and 13mm (1/2 inch) drill bits
- Hack Saw
- Philips Screwdriver
Hardware List
| Item No. | Reference Image Description | Quantity |
|---|---|---|
| A | Cam lock (15x11mm) | x16 |
| B | Cam bolt (7x32mm) | x16 |
| C | Wood dowel (8x40mm) | x16 |
| D | Screw (4x14mm) | x48 |
| E | Plastic anchor (8*40mm) | x10 |
| F | Screw (4*50mm) | x10 |
| G | Sticker | x16 |
| H | Elliptical clothing base | x6 |
| I | Shelf support | 8 set |
| J | L-shaped angle iron | x8 |
| K | Anti overturning L-piece | x4 |
| P | Elliptical Clothing (1194mm) - Hanging Rod | x3 |
| Q | Elliptical clothing with blocked ends - Rod End Caps | x6 |
Important Notes:
- Carefully remove all parts from the carton and place them individually on a soft cloth to prevent scratches or other damage.
- Strictly follow these assembly and installation instructions to ensure a completed product as designed.
- Do not tighten all screws until each part is properly assembled.
Assembly Instructions
Step 1: Prepare Panels
TOP UNIT: Attach Part 1 (shelf) to Part 3 (right side panel) using 2x Cam Bolts (B) and 2x Wood Dowels (C). Attach Part 2 (left side panel) to Part 3 (right side panel) using 2x Cam Bolts (B) and 2x Wood Dowels (C).
BASE UNIT: Attach Part 6 (shelf) to Part 8 (right side panel) using 2x Cam Bolts (B) and 2x Wood Dowels (C). Attach Part 7 (left side panel) to Part 8 (right side panel) using 2x Cam Bolts (B) and 2x Wood Dowels (C).
Visual description: Diagrams show two separate units being assembled. For each unit, two side panels are connected to a shelf/panel piece using bolts and dowels inserted into pre-drilled holes.
Step 2: Insert Dowels
TOP UNIT: Insert 2x Wood Dowels (C) into Part 1 (shelf) to connect it to Part 2 (left side panel). Insert 2x Wood Dowels (C) into Part 5 (shelf) to connect it to Part 2 (left side panel).
BASE UNIT: Insert 2x Wood Dowels (C) into Part 6 (shelf) to connect it to Part 7 (left side panel). Insert 2x Wood Dowels (C) into Part 5 (shelf) to connect it to Part 7 (left side panel).
Visual description: Diagrams show dowels being inserted into shelves and then connecting to side panels.
Step 3: Secure Shelves with Cam Locks
TOP UNIT: Secure Part 1 (shelf) to Part 3 (right side panel) using 2x Cam Locks (A). Secure Part 5 (shelf) to Part 3 (right side panel) using 2x Cam Locks (A).
BASE UNIT: Secure Part 6 (shelf) to Part 8 (right side panel) using 2x Cam Locks (A). Secure Part 5 (shelf) to Part 8 (right side panel) using 2x Cam Locks (A).
Visual description: Diagrams show cam locks being inserted and tightened to secure the shelves to the side panels.
Step 4: Attach Side Panels
TOP UNIT: Attach Part 2 (left side panel) to Part 1 (shelf) and Part 5 (shelf) using 2x Wood Dowels (C) for each connection (total 4 dowels).
BASE UNIT: Attach Part 7 (left side panel) to Part 6 (shelf) and Part 5 (shelf) using 2x Wood Dowels (C) for each connection (total 4 dowels).
Visual description: Diagrams show the remaining side panels being attached to the shelves using dowels.
Step 5: Secure Side Panels with Cam Locks
TOP UNIT: Secure Part 3 (right side panel) to Part 1 (shelf) and Part 5 (shelf) using 2x Cam Locks (A) for each connection (total 4 cam locks).
BASE UNIT: Secure Part 8 (right side panel) to Part 6 (shelf) and Part 5 (shelf) using 2x Cam Locks (A) for each connection (total 4 cam locks).
Visual description: Diagrams show the remaining side panels being secured to the shelves using cam locks.
Step 6: Attach Brackets
TOP UNIT: Attach 4x L-shaped angle irons (J) to the back edges of the assembled TOP UNIT, using 4x Screws (D) per bracket (total 16 screws).
BASE UNIT: Attach 4x L-shaped angle irons (J) to the back edges of the assembled BASE UNIT, using 4x Screws (D) per bracket (total 16 screws).
Visual description: Diagrams show L-shaped brackets being screwed onto the rear corners of both the top and base units.
Step 7: Attach Anti-Overturning Pieces
TOP UNIT: Attach 2x Anti-overturning L-pieces (K) to the top back edge of the TOP UNIT, using 2x Screws (D) per piece (total 4 screws).
BASE UNIT: Attach 2x Anti-overturning L-pieces (K) to the top back edge of the BASE UNIT, using 2x Screws (D) per piece (total 4 screws).
Visual description: Diagrams show L-shaped anti-tip pieces being attached to the upper rear edges of both units.
Step 8: Secure Unit to Wall (Base Unit)
Position the BASE UNIT against the wall. Secure the unit to the wall by fastening through the anti-overturning pieces (K) on the base unit. Use 2x Plastic Anchors (E) and 2x Screws (F) for each side panel (Part 7 and Part 8).
Visual description: Diagram shows the base unit positioned against a wall, with fasteners being driven through the anti-tip brackets into the wall.
Step 9: Connect Top and Base Units
Place the assembled TOP UNIT onto the assembled BASE UNIT. Join the two units using 4x Wood Dowels (C) inserted into the designated holes.
Visual description: Diagram shows the top section being lowered onto the base section, with dowels aligning for connection.
Step 10: Secure Unit to Wall (Combined Unit)
Ensure the combined unit is correctly positioned against the wall. Secure the unit to the wall by fastening through the anti-overturning pieces (K) on the top unit. Use 2x Plastic Anchors (E) and 2x Screws (F) for each side panel (Part 2 and Part 7).
Visual description: Diagram shows the complete stacked unit against a wall, with fasteners being driven through the anti-tip brackets into the wall.
Step 11: Install Shelf Supports and Shelves
Insert 8x Shelf Supports (I) into the pre-drilled holes on the inner sides of the unit at the desired shelf heights. Place the 4x Part 4 shelves onto the shelf supports.
Visual description: Diagrams show shelf supports being inserted into the unit's side panels, and then shelves being placed on top of these supports.
Step 12: Attach Hanging Pole Bases
Attach 3x Hanging clothes pole bases (H) to the side panels of the unit. Each base is secured using 2x Screws (D).
Visual description: Diagrams show the metal bases for hanging rods being screwed onto the interior side panels of the assembled unit.
Step 13: Install Hanging Rods
Insert 3x Hanging Rods (P) into the attached hanging pole bases (H). Ensure the rods are securely seated.
Visual description: Diagrams show the metal hanging rods being inserted into the previously attached bases.
Step 14: Prepare Hanging Rods
If necessary, use a hacksaw to cut the hanging rods (P) to the correct length. Attach 2x Rod End Caps (Q) to each cut rod (total 6 end caps for 3 rods).
Visual description: Diagram shows a rod being cut with a hacksaw, and then end caps being fitted onto the ends of the rod.
Step 15: Final Assembly
The Storage Box system is now fully assembled and installed. The hanging rods are in place, ready for use.
Visual description: Diagram shows the completed storage unit with hanging rods installed, ready for use.
