Kichler 3-Light Vanity

Package Contents

Hardware Contents

Safety Information

[warning] Please read and understand this entire manual before attempting to assemble, operate, or install the product.

[warning] CAUTION – RISK OF SHOCK – Disconnect power at the main circuit breaker panel or main fusebox before starting and during installation.

[warning] This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.

[warning] Do not use bulbs with wattage greater than specified on this fixture.

[warning] California Proposition 65: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

[warning] CAUTION: If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor. All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate ETL listing and/or C.S.A. certification of this fixture.

Preparation

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated assembly time: 30 minutes to 1 hour.

Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses.

Assembly Instructions

1. Mounting Bracket Installation: Orient the mounting bracket (B) so the raised center portion protrudes into the outlet box. Insert long machine screws (DD) through mounting bracket (B). With long machine screws (DD) protruding outward, connect the mounting bracket (B) to the outlet box (not included) with short machine screws (BB).

   Diagram Description: Shows mounting bracket (B) attached to an outlet box using screws (BB) and long screws (DD).

2. Wire Connection Guide:

   Ground wire:

   • For installation in the United States: Wrap ground wire from outlet box around ground screw on mounting bracket (B) no less than 2 inches from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA).
   • For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with the wire connector (AA).

   Supply wires:

   • Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord "D" shaped and ribbed).
   • Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).

   Note: Fixture wires will either be: Black and White; or Parallel Cord SPT-1 lamp wire with one round smooth wire and one "D" shaped ribbed wire.

   Diagram Description: Illustrates electrical wiring connections. Shows connecting bare copper or green ground wire to the ground screw on the mounting bracket, then using a wire connector (AA). Shows connecting black supply wire to black fixture wire and white supply wire to white fixture wire, accommodating different wire types like parallel cords.

3. Canopy Installation: Pass canopy (A) over the long machine screws (DD) protruding from the mounting bracket (B) and secure in place with threaded knobs (CC).

   Diagram Description: Shows canopy (A) being placed over the protruding long screws (DD) from the mounting bracket (B) and secured with threaded knobs (CC).

4. Bulb Installation: Insert a 60-watt max. medium base bulb or LED equivalent (not included) into socket (C). Repeat for remaining sockets.

   Diagram Description: Shows a light bulb being inserted upwards into the socket (C).

Care and Maintenance

• Always be certain that electric current is turned off before cleaning this item.
• Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish.
• All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.

Troubleshooting