Mi Handheld Vacuum Cleaner User Manual

Safety Information

Usage Restrictions

• Intended for home and in-car use only; not for outdoor, commercial, or industrial environments.
• Avoid storing the vacuum in cars during extreme temperatures to protect battery life.
• Do not use in high humidity or temperatures above 40°C or below 3°C.
• Children should be supervised to ensure they do not play with the appliance.
• Appliance not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience, unless supervised.
• Children aged 8+ and persons with reduced capabilities may use the appliance under supervision and with understanding of hazards. Children should not play with it, and cleaning/maintenance should be supervised.
• Keep hair, loose clothing, fingers, and body parts away from openings and moving parts.
• Keep limbs and pets away from rotating brush heads on electric brush heads to prevent injury.
• Do not touch the power supply or operate with wet hands.
• Do not vacuum liquids (e.g., water, cola).
• Do not vacuum burning or smoking substances (e.g., cigarette butts).
• Do not vacuum hard or pointy objects (e.g., building materials, glass, nails).
• Use the product according to the User Manual; users are responsible for damage from improper use.
• Product is intended for use in areas below 3,000 meters above sea level.

Battery & Charging

WARNING

• Batteries are replaceable only by skilled persons.
• Use only ATC01RR or BTC01RR power supply for charging.
• Do not use third-party batteries, power adapters, or docking stations.
• Do not disassemble, repair, or modify the battery, power adapter, or docking station.
• Avoid charging or installing the docking station near heat sources or in humid areas.
• Do not wipe the adapter or docking station with a wet cloth, or touch them with wet hands.
• If the power cord is damaged, stop use and contact after-sales service.
• For extended periods of non-use, fully charge, unplug, and store in a cool, dry place. Recharge every three months to prevent over-discharge.

The lithium-ion battery contains substances harmful to the environment.

ATTENTION:

• Remove the battery before scrapping the appliance.
• Disconnect from the mains supply when removing the battery.
• Dispose of batteries safely through a professional organization; do not discard as waste.

Removing the Battery (for scrapping):

1. Remove the dust compartment and cyclone assembly. Unscrew the two screws on the inner wall near the dust compartment release switch.
2. Remove the top fan filter and the screw fixing the handle cover.
3. Open the handle cover along the gap and slide it up to remove.
4. Unplug the 3 connectors inside the handle from the battery.
5. Slide out the battery pack.

Transportation

• Recommended to transport the vacuum in its original packaging.

Note

• Rinse the filter at least once a month with tap water. Refer to Maintenance for details.

Beijing Roborock Technology Co., Ltd. declares compliance with applicable Directives and European Norms. The full EU declaration of conformity is available at: www.mi.com/global/service/support/declaration.html

Product Overview

Vacuum Cleaner Components:

• Top Fan Filter
• Dust Compartment:
  • Note 1: The pattern on the dust compartment and floor attachment is a parting line from the production process, not a crack or error.
  • Note 2: Powder in the dust compartment or cyclone assembly is lubricating powder for assembly, not a trace of use.
• Dust Compartment Opening Switch
• Dust Compartment Release Switch
• MAX Button: Press and hold the switch, then press the MAX button to engage MAX mode. In MAX mode, the fan runs at full speed, reducing battery life and blowing hot air. Turning off the vacuum reverts to Standard mode.
• MAX-LED Indicator: Off = Standard Mode, On = MAX mode.
• On/Off Switch: Push to turn on, release to turn off.
• LED Battery Status Indicator:
  • Red: Battery level < 20%
  • Orange: Battery level 20% - 60%
  • White: Battery level > 60%
  • Off: Battery fully charged or vacuum off.
  • Slowly Blinking Orange: Temporary protection due to high/low battery temperature; wait for temperature to normalize.
  • Slowly Blinking Red: Low battery; charge before use.
  • Quickly Blinking Red: 1. Battery charging protection (unplug/replug for 1 min). 2. Hardware error (contact after-sales service).
• Charging Port

Accessories

• Power Supply
• Crevice Nozzle: Suitable for narrow crevices like around doors, windows, and stairs.
• Brush Nozzle: Suitable for vacuuming sofas, seats, etc.
• Floor Attachment: Suitable for various floor types.
• Bed Attachment: Suitable for vacuuming dust and mites on textile surfaces like beds and curtains.
• Extension Rod

Installation

Vacuum and Accessories Installation Diagram

Method One:

Diagram showing how to attach accessories to the extension rod or vacuum body, with arrows indicating insertion until a click is heard.

Method Two:

Diagram illustrating the removal of an accessory, with an arrow pointing to the quick release switch to be pressed.

Mi Handheld Vacuum Cleaner Docking Station Installation

The docking station must be purchased separately. Visit www.mi.com.

1. The docking station is an optional accessory.
2. Install in a cool, dry place near a power outlet, away from direct sunlight.
3. Use appropriate mounting hardware for your wall type. Ensure the installation area is clear of pipes (gas, water, air, electricity, drainage).
4. Professional installation is recommended, using protective clothing and goggles.
5. Drill 6mm holes, insert wall plugs. Align docking station holes with wall holes and tighten screws.

Diagram: Shows storing the vacuum on the docking station.

Diagram: Shows a wall plug, screw, and charging socket. A height indicator shows 1.06 meters from the ground.

Diagram: Shows pulling the vacuum down onto the docking station to charge.

Instructions

Charging

LED Battery Status Indicator: (See Product Overview section for details)

Notes:

1. First-time use: Fully charge the vacuum before use.
2. When charging, the vacuum stops operating and enters Charging mode.
3. After continuous MAX mode use, the battery may be hot, increasing charging time. Allow the vacuum to cool for 30 minutes before charging.

Please read the Safety Instructions before proceeding.

Diagram: Illustrates the vacuum being charged via its power supply.

Diagram: Shows the vacuum being charged on its docking station.

Vacuum Usage

• Carpets may fluff when vacuumed; use brush or crevice nozzle if this occurs.
• For highly polished floors, check the floor brush for foreign objects to prevent scratching.
• Ensure the dust compartment is installed before use.
• Do not block the exhaust port during vacuuming.
• Vacuum fine dust (e.g., flour) only in small amounts.
• Do not vacuum sharp objects, small toys, pins, paper clips, etc., to avoid damage.
• When cleaning dangerous areas (stairs, windows), pay attention to personal safety.
• Do not place or lean the vacuum on tables or chairs to prevent damage from dropping or slipping.
• The vacuum brush's movement may affect gloss on waxed floors; wipe with a damp cloth and polish with wax.

Automatic Turn-off Feature

1. If rotating parts get stuck, the product may turn off; it can be used again after removing foreign objects.
2. If the motor enters overheating protection mode, it will automatically turn off. Wait for the brush head to cool down before re-use.

Cleaning String-like Materials from the Roller Brush

1. If the roller stops rotating due to entanglement with large objects or hair, clean it immediately.
2. Detach the brush head from the vacuum before removing foreign objects to prevent accidental activation and injury.
3. Be careful of sharp objects when clearing materials.
4. If entangled objects cannot be removed easily, refer to the "Cleaning the Roller" section for roller removal.

Brush Head Usage

1. Crevice Nozzle: For narrow crevices (doors, windows, stairs).
2. Brush Nozzle: For sofas, seats, etc.
3. Bed Attachment: For dust and mites on textile surfaces (beds, curtains).
4. Floor Attachment: For various floor types.

Note: Brushes can be used independently to vacuum dust from the vacuum cleaner or electric brush heads.

Product Maintenance

• Always use genuine parts to avoid voiding the warranty.
• If the filter or nozzle is clogged, the fan may stop working. Rinse the filter/nozzle immediately.
• For extended non-use, store in a cool, dry place, away from direct sunlight or humidity.
• For extended non-use, fully charge, unplug, and store in a cool, dry place. Recharge every three months to prevent over-discharge.

Cleaning the Vacuum

Wipe the vacuum with a soft, dry cloth.

Maintenance: Cleaning the Dust Compartment

Recommended to clean the dust compartment at least once a month.

1. Before cleaning, disconnect the adapter and turn off the vacuum. Empty the compartment when dust reaches the "MAX" mark to maintain vacuuming performance.
2. To empty: Push the switch on the dust compartment in the direction of the arrow to open the bottom cover and empty into a trash can.
3. To rinse: Push the switch next to the dust compartment in the arrow's direction, pull the compartment away, and rinse with water.
4. Rinse the dust compartment with water at least once a month. Wipe contact points with a soft dry cloth if dirty.
5. After cleaning, dry the dust compartment completely before reinstalling. Follow the figure for reinstallation steps.

Caution: Do not use detergents, polishes, or air fresheners to rinse the dust compartment. Do not rinse in a dishwasher or other device.

Rinsing the Internal Filter and Cyclone Assembly

Recommended to rinse at least once a month.

1. Before cleaning, disconnect the product from the supply and avoid pressing the power switch.
2. Inspect and rinse the internal filter and cyclone assembly regularly for optimal performance.
3. The filter may need more frequent rinsing if used for fine dust or in MAX mode.
4. To rinse: Remove the dust compartment. Rotate the cyclone assembly counter-clockwise and remove it. Remove the internal filter. Rinse both with tap water.
5. Rinse until clean. Wring out the filter after rinsing.
6. To dry thoroughly, keep the filter and cyclone assembly in a ventilated or cool place for at least 24 hours.

Caution: Do not rinse the filter in a dishwasher or washing machine, or dry it in a tumble dryer, oven, microwave, or near an open fire.

After drying, reinstall the filter and cyclone assembly.

Steps to Remove the Internal Filter and Cyclone Assembly

1. Remove the dust compartment as shown in the figure.
2. Rotate the cyclone assembly in the direction shown in the figure.
3. Remove the internal filter from the cyclone assembly.
4. Rinse the filter and cyclone assembly until clean. Wring out the filter.
5. Dry thoroughly in a ventilated or cool place for at least 24 hours.
6. After drying, reinstall the filter and cyclone assembly.

Steps to Install the Internal Filter and Cyclone Assembly

1. Place the filter facing up as shown in the figure.
2. Place the filter on top of the cyclone assembly and gently push it into place, pushing aside the safety clip on the left side of the notch.
3. Align the cyclone assembly with the vacuum and turn it clockwise to lock it in place.
4. Slightly tilt the dust compartment when installing it on the vacuum.
5. Gently push the dust compartment in the indicated direction until a click is heard, confirming it is secured.

Rinsing the Top Fan Filter

Recommended to rinse at least once a month.

1. Turn the top fan filter counterclockwise to the unlocked position and remove it from the vacuum.
2. Rinse the inside of the top filter under the tap. Rotate the filter while rinsing to ensure all dust in the gaps is removed. Tap the filter against the sink several times to remove remaining dust.
3. Repeat rinsing four to five times until the filter is clean.
4. To dry thoroughly, keep the filter in a ventilated or cool place for at least 24 hours after cleaning.
5. After drying, reinstall the filter by aligning it with the unlocked position and turning it clockwise until it locks into place.

Cleaning the Roller

Follow instructions to check and clean the roller regularly for optimal performance. Detach the brush head from the vacuum before removing the roller to avoid accidental activation and injury.

Caution: The bed attachment roller must be removed and cleaned separately. The bed attachment and floor attachment contain electrical components. The floor attachment roller contains bearings. Do not clean these parts with water.

Cleaning the Floor Attachment

1. Place the floor attachment facing you. Use a coin to turn the lock counterclockwise by 90° to the unlocked position.
2. Turn the end cap to the open position. Gently slide the roller away from the head.
3. Separate the end cap from the roller and remove any wrapped hair.
4. After cleaning, install the end cap back on the roller.
5. Confirm the end cap is installed. Put the roller back as shown in the figure. Turn the end cap to the locked position.
6. Rotate the latch clockwise by 90° to the locked position to secure the roller.

Cleaning the Bed Attachment

1. With the side latch of the brush head facing you, use a coin to turn the latch counterclockwise until it comes off.
2. Remove the roller from the bed attachment.
3. Rinse and clean the roller.
4. Place the roller vertically and keep it in a ventilated or cool place for at least 24 hours to dry.
5. After confirming the roller is dry, put it back in place.
6. With the side latch facing you, use a coin to turn the latch clockwise into the locked position, ensuring the roller is in place.

Specifications

Vacuum Cleaner

Power Supply

Troubleshooting

Refer to the table below for handling errors when the vacuum cleaner does not work properly.

WEEE Information

Products with this symbol are waste electrical and electronic equipment (WEEE) and should not be mixed with unsorted household waste. Protect human health and the environment by handing over waste equipment to a designated collection point for recycling. Correct disposal and recycling prevent negative environmental and health consequences. Contact local authorities for information on collection points and terms.

WARRANTY NOTICE

This warranty grants specific rights, and you may have other rights conveyed by laws of your country, province, or state. Consumer law in some jurisdictions may impose a minimum warranty period.

Xiaomi does not exclude, limit, or suspend other rights you may have, except as permitted by law. Consult your country's laws for a full understanding of your rights.

1. LIMITED PRODUCT WARRANTY

XIAOMI warrants that Products are free from defects in materials and workmanship under normal use, as per the user manual, during the Warranty Period. Legal warranty duration and conditions are provided by local laws. Refer to Xiaomi's official website for consumer warranty benefits: https://www.mi.com/en/service/warranty/.

Xiaomi warrants to the original purchaser that its products will be free from defects in materials and workmanship under normal use during the warranty period. Xiaomi does not guarantee uninterrupted or error-free operation and is not liable for damages from non-compliance with instructions.

2. REMEDIES

If a hardware defect is found and a valid claim is received within the Warranty Period, Xiaomi will either (1) repair the product at no charge, (2) replace the product, or (3) refund the product (excluding shipping costs).

3. HOW TO OBTAIN WARRANTY SERVICE

To obtain warranty service, deliver the Product in its original or similar protective packaging to the address specified by Xiaomi. Xiaomi may require proof of purchase or registration before providing service, as permitted by law.

4. EXCLUSIONS AND LIMITATIONS

This Limited Warranty applies only to Products manufactured by or for Xiaomi, identified by Xiaomi trademarks. It does not apply to:

• (a) Damage due to acts of nature (lightning, flood, fire, etc.).
• (b) Negligence.
• (c) Commercial use.
• (d) Alterations or modifications to the Product.
• (e) Damage caused by use with non-Xiaomi products.
• (f) Damage caused by accident, abuse, or misuse.
• (g) Damage caused by operating the Product outside permitted uses or with improper voltage/power supply.
• (h) Damage caused by service performed by non-Xiaomi representatives.

It is your responsibility to back up data. Xiaomi is not responsible for data loss or reformatting during service.

No Xiaomi reseller, agent, or employee is authorized to modify this warranty. If any term is illegal or unenforceable, the rest remain unaffected.

After-sales services are limited to the country/region of original purchase, unless otherwise promised by Xiaomi or prohibited by law.

Products not duly imported, manufactured, or acquired from Xiaomi or its official sellers are not covered. You may benefit from warranties from non-official retailers; contact your retailer.

Warranties do not apply in Hong Kong and Taiwan.

5. IMPLIED WARRANTIES

Implied warranties (merchantability, fitness for a particular purpose) are limited in duration to the maximum duration of this limited warranty, as permitted by law. Some jurisdictions may not allow duration limitations.

6. DAMAGE LIMITATION

Xiaomi is not liable for indirect, special, or consequential damages (including loss of profits, revenue, or data) resulting from any breach of warranty or condition, even if informed of the possibility of such damages, as permitted by law. Some jurisdictions may not allow these limitations.

7. XIAOMI CONTACTS

For customer service, visit: https://www.mi.com/en/service/warranty/. Contact persons for after-sale service include Xiaomi's authorized service network, distributors, or the vendor. Contact the relevant person if in doubt.