Mi Vacuum Cleaner G10 User Manual

Introduction

This document serves as the user manual for the Mi Vacuum Cleaner G10, providing comprehensive instructions for its safe operation, maintenance, and troubleshooting.

Safety Instructions

This product is for household use only. Read this manual carefully before use, and retain it for future reference.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

The appliance is only to be used with the power supply unit provided with the appliance.

The vacuum cleaner is not a toy. Children may not play with or operate this product. Please exercise caution when using the vacuum cleaner near children. Do not allow children to clean or maintain the vacuum cleaner unless supervised by a parent or guardian.

Only use the vacuum cleaner on dry indoor surfaces. Do not install, charge, or use this product outdoors, such as in bathrooms, or near a pool.

Do not touch the plug or any part of the vacuum cleaner with wet hands.

To reduce the risk of fire, explosion, or personal injury, check to make sure the lithium-ion battery and charger are undamaged before use. Do not use the vacuum cleaner if either the battery or charger is damaged.

The smart high torque brush bar, mini electric brush, battery, extension rod, and the vacuum cleaner are electrically conductive and should not be immersed in water or other liquid. Make sure all parts are thoroughly dry after you carry out cleaning on them.

To prevent injury caused by moving parts, turn off the vacuum cleaner before cleaning the smart high torque brush bar and mini electric brush. The smart high torque brush bar, dust compartment, and filter must all be properly installed before using the vacuum cleaner.

Only use the BLJ24W308080P-V battery charger provided with the appliance.

Only use the P2046-7S1P-BC/P2046-7S1P-BCA battery pack provided with the appliance.

If the charger or battery becomes damaged, it must be replaced with a genuine component purchased from the manufacturer or after-sales service department.

Do not use the vacuum cleaner to pick up flammable or combustible liquids, such as gasoline, bleach, ammonia, or drain cleaners; nor other liquids like water.

Do not use the vacuum cleaner to pick up drywall particles, ashes like fireplace ash, or smoking or burning materials such as coal, cigarette butts or matches.

Do not use the vacuum cleaner to pick up sharp or hard objects, such as glass, nails, screws, or coins, which may damage the product.

Keep hair, loose clothing, fingers, and other parts of the body away from the vacuum cleaner's openings and moving parts. Do not point the suction opening, extension rod, or other accessories at your eyes or ears or put them in your mouth.

Do not put any object into the vacuum cleaner's openings, nor use the vacuum cleaner with any opening blocked. Keep free of dust, lint, hair, or other items which may reduce airflow.

Do not rest the vacuum cleaner against a chair, table, or other unstable surfaces, as this may cause damage to the product or personal injury. If the vacuum cleaner malfunctions because of being knocked over or damaged, please contact the authorized service department. Never attempt to disassemble the vacuum cleaner on your own.

Only use the original charger to charge the product in environments with an ambient temperature of 0°C to 40°C. Otherwise, the battery may damage.

The dust compartment cover, pre-filter, cyclone assembly, and HEPA filter must all be properly installed prior to using the vacuum cleaner.

Make sure the vacuum cleaner is unplugged when not used for extended periods as well as prior to performing any maintenance or repairs.

Please be extra careful when using the vacuum cleaner to clean stairs.

Fire Hazard Warning: Do not apply any type of fragrance to the vacuum cleaner's filter. These types of products are known to contain flammable chemicals which may cause the vacuum cleaner to catch fire.

When Battery is not in use, keep it away from all metal objects, such as paper clips, coins, keys, nails, or screws. Shorting the battery terminals together increases the risk of fire or burns.

Under abusive conditions, liquid may be ejected from the battery. Avoid contact with liquid, as it may cause irritation or burns. If contact occurs, flush with water. If liquid contacts eyes, seek medical help.

DO NOT expose the battery and appliance to fire as it may cause explosion.

DO NOT expose or submerge the battery and appliance in any water, salt water, or other liquids.

Please strictly follow the instructions in this user manual when using the vacuum cleaner. Users are responsible for any loss or damage that may arise from improper use of the vacuum cleaner.

We Dreame (Tianjin) Information Technology Co., Ltd., hereby, declare that this equipment is in compliance with the applicable Directives and European Norms, and amendments. The full text of the EU declaration of conformity is available at the following internet address: http://www.mi.com/global/service/support/declaration.html

For detailed e-manual, please go to www.mi.com/global/service/userguide

Product Overview

Accessories List

Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.

• Smart High Torque Brush Bar: For cleaning different types of flooring such as wood, marble, tile, and short carpet.
• Crevice Nozzle: For vacuuming narrow crevices and areas around doors, windows, baseboards, corners, stairs, etc.
• Charger: For charging the vacuum cleaner.
• 2-in-1 Charging & Storage Mount: Includes screw x 2, wall plug x 2, and mounting template sticker.
• Extension Rod: Connects to the main unit and brush bars.
• Mini Electric Brush: For vacuuming dirt, pet hair, and other stubborn debris from sofas, bedding, and other fabric surfaces.
• 2-in-1 Brush Nozzle: For vacuuming curtains, sofas, vehicle interiors, coffee tables, etc.
• Water Tank: Used for the mopping function.
• Mop Pad: Attaches to the water tank for mopping.

Component Name

Diagram showing the main parts of the vacuum cleaner:

• Charging Port: Where the charger connects.
• Display Screen: Shows battery status and other information.
• Battery Status Indicator: Visual indicator for battery level.
• Power Button: Press to turn on, release to turn off.
• Battery Release Button: Used to detach the battery pack.
• Dust Compartment: Collects dirt and debris.
• Antistatic Contact: Component for static discharge.
• Charging Contacts x 2: Connects to the charger or charging mount.
• Dust Compartment Release Switch: Used to detach the dust compartment.
• Dust Compartment Bottom Cover Release Button: Used to empty the dust compartment.

Display Screen

The display screen shows the current battery level as a percentage during charging. When the number reaches 100, the battery is fully charged.

Battery Level Indicator:

• Green: Battery level > 20%
• Red: Battery level ≤ 20%

Suction Level Button: Press to switch between suction levels (eco, standard/auto, high power). The corresponding suction level will be highlighted on the display screen.

Lock/Unlock Status: Indicates the lock status of the vacuum cleaner.

Electronic Lock Button: Press to lock/unlock the vacuum cleaner.

Note: If the vacuum cleaner experiences a malfunction, the display screen will show an error message. Refer to the Troubleshooting section for solutions.

How to Install

Installing the Accessories onto the Vacuum Cleaner

Insert accessories until they click into place.

Note: The mini electric brush should not be used with the extension rod.

Diagrams illustrate attaching the extension rod, brush bars, and nozzles to the main unit.

Installing the 2-in-1 Charging & Storage Mount

1. Install the mount in a cool, dry place near an electrical outlet. Ensure there are no wires or pipes behind the installation area.
2. The bottom of the mounting template sticker should be level and at least 1.03 meters from the ground, with at least 30 cm of clearance above it.
3. Use a power drill with an 8 mm drill bit to drill holes at the marked positions on the template sticker, then insert wall plugs into each hole.
4. Align the mounting holes on the 2-in-1 charging & storage mount with the holes on the wall, and attach the mount using the included screws.

Recommended Height: At least 1.03 meters from the ground.

Charging

Battery Status Indicator

The indicator shows the battery status:

• Off: Battery is off.
• Blinking: Low battery.
• On: Battery is charging or has sufficient charge.
• Half battery: Approximately 50% charged.
• Nearly full: Approximately 80% charged.
• Fully charged: 100% charged.

Once the vacuum cleaner is fully charged, the indicator will turn off after 5 minutes, and the vacuum cleaner will enter the energy-saving mode.

Charging the vacuum cleaner with the charger: A diagram shows the vacuum cleaner connected to the charger.

Charging the vacuum cleaner on the charging mount: A diagram shows the vacuum cleaner docked on the charging mount.

Notes:

• Fully charge the vacuum cleaner before using it for the first time. This will take about 4 hours.
• The vacuum cleaner cannot be used while charging.
• Vacuuming at the highest suction level for a prolonged period may cause the battery to heat up, potentially increasing charging time. It is recommended to cool the vacuum cleaner down for 30 minutes before charging if it has been used extensively.

How to Use

Setting Language

Press and hold the [button O] for 3 seconds to open the language list. Press the [button O] to scroll through languages and select the desired one. Press and hold the [button O] for 2 seconds to confirm the selection.

Note: The display screen will turn off if there is no operation for more than 10 seconds.

Switching Suction Levels

Press the [suction level button] to cycle through suction levels: Eco, Standard/Auto, and High Power. The corresponding suction level will be highlighted on the display screen.

When using the Smart High Torque Brush Bar, the Auto mode is activated, indicated by "Auto" on the display. The vacuum cleaner automatically adjusts suction between floor/tile and carpet.

Note: If you stop the vacuum cleaner during cleaning, it will resume with the last selected suction level when started again.

Working Modes

The vacuum cleaner has two working modes:

1. Non-continuous Mode: Hold down the [power button] to start the vacuum cleaner, and release to stop it.
2. Continuous Mode: Press the [continuous mode button] to enable Continuous Mode, then press the [power button] to turn the vacuum cleaner on. To exit Continuous Mode, press the [continuous mode button] again.

Continuous Mode allows the vacuum cleaner to run without holding the power button, freeing up your fingers.

Notes:

• In Continuous Mode, pressing the power button puts the vacuum cleaner into standby. Pressing it again resumes operation.
• If the vacuum cleaner remains in standby for over 10 seconds, the display screen will turn off, and Continuous Mode will be exited.

Using Different Accessories

• 2-in-1 Brush Nozzle: For vacuuming curtains, sofas, vehicle interiors, coffee tables, etc.
• Mini Electric Brush: For vacuuming dirt, pet hair, and other stubborn debris from sofas, bedding, and other fabric surfaces.

Notes:

• If any rotating part becomes stuck, the vacuum cleaner may shut off automatically. Remove trapped foreign objects and resume use.
• If the motor overheats, the vacuum cleaner will shut off automatically. Wait until the battery temperature returns to normal before resuming use.

• Crevice Nozzle: For vacuuming narrow crevices and areas around doors, windows, baseboards, corners, stairs, etc.
• Smart High Torque Brush Bar: For cleaning various flooring types like wood, marble, tile, and short carpet. In Auto Mode, it adjusts suction based on surface type.

Note: The smart high torque brush bar can be attached directly to the vacuum cleaner.

Using the Mopping Function

Notes:

• Do not step on the water tank, as this could cause permanent damage.
• Heavily soiled floors should be vacuumed prior to mopping for better results.
• Do not use the mopping function on carpet.
• Do not use any cleaning agents or disinfectants.

1. Dampen the mop pad and wring out excess water, then attach it securely to the bottom of the water tank.
2. Open the water tank plug, add an appropriate amount of clean water, then close the plug.
3. Attach the smart high torque brush bar to the water tank by aligning the magnets on each component until they snap together.
4. This function is designed for vacuuming and wiping down hardwood and tile floors.

Notes:

• The ball valve in the water tank controls water dispensing. It is a moving part and may make a rolling sound when starting and stopping, which is normal.
• When not in use, keep the switch in the OFF position.

Care & Maintenance

Maintenance Precautions

• Always use genuine parts to keep your warranty valid.
• If the filter, extension rod, or smart torque brush bar becomes clogged, the vacuum cleaner will stop working. Clean the clogged component to restore functionality.
• If the vacuum cleaner will not be used for an extended period, fully charge it, disconnect it from the power, and store it in a cool, low-humidity environment away from direct sunlight. To prevent battery over-discharge, recharge the vacuum cleaner at least once every three months.

Cleaning the Vacuum Cleaner

Wipe the vacuum cleaner with a soft, dry cloth.

Cleaning the Dust Compartment, Pre-filter, and Cyclone Assembly

1. The vacuum cleaner's performance is reduced if the dust compartment is filled to the "MAX" mark. Empty the dust compartment promptly to regain performance. Ensure the vacuum cleaner is disconnected from power and the power button is not pressed before emptying.
2. Press the dust compartment bottom cover release button, then empty the contents.
3. Push the dust compartment release switch in the indicated direction [right-arrow], then gently remove the dust compartment.
4. Remove the pre-filter first. Lift the handle of the cyclone assembly and turn it counterclockwise until it stops, then pull to lift out the cyclone assembly.
5. Rinse the pre-filter, cyclone assembly, and dust compartment with water until clean. Set each component aside to dry thoroughly for at least 24 hours [24-hour-drying].

Notes:

• The dust compartment should be rinsed out at least once a month.
• The pre-filter and cyclone assembly should be cleaned every 3 to 4 months.
• Wipe the contact points of the vacuum cleaner with a soft dry cloth if they are dirty.

Notes:

• Do not use detergents, polishes, or air fresheners to clean the dust compartment.
• Do not clean the dust compartment, pre-filter, or cyclone assembly in a dishwasher or washing machine, nor attempt to dry any component in a tumble dryer, oven, microwave, or near an open fire.

Installing the Dust Compartment, Pre-filter, and Cyclone Assembly

1. Insert the cyclone assembly vertically into the dust compartment. Align the cyclone assembly handle with the slot on the left side of the dust compartment. Turn the handle clockwise until it locks, then flip the handle down.
2. Place the pre-filter with its front side facing up into the cyclone assembly.
3. Slightly tilt the dust compartment so its slot aligns with the clip on the vacuum cleaner. Gently push the dust compartment until it clicks into place [click-sound].

Cleaning the HEPA Filter

Note: It is recommended to clean the HEPA filter once every 4 to 6 months.

1. Remove the HEPA filter from the vacuum cleaner by pulling it down in the indicated direction [down-arrow].
2. Clean the HEPA filter with clean water. Rotate the HEPA filter 360° to thoroughly remove all dust. Lightly tap the filter several times to remove excess dirt.

Notes:

• Only use clean water to clean the filter. Do not use detergent.
• Do not attempt to clean the HEPA filter with a brush or finger.

Allow the HEPA filter to thoroughly dry for at least 24 hours [24-hour-drying].

Installing the HEPA Filter

1. Insert the HEPA filter into the vacuum cleaner and gently press down until it clicks into place [click-sound].
2. Reinstall the dust compartment.

Cleaning the Smart High Torque Brush Bar

1. Turn the lock counterclockwise [left-arrow] until it stops, then remove the roller brush from the smart high torque brush bar.
2. Use scissors to cut and pick out any hair or other debris tangled around the roller brush. Wipe away excess dust from the slot and clear plastic cover using a dry cloth or paper towel.
3. After extended use, the roller brush may become dirty and should be washed.
4. After washing, allow the roller brush to dry thoroughly by standing it upright in a well-ventilated area for at least 24 hours [24-hour-drying].

Cleaning the Mini Electric Brush

1. Use a coin to turn the lock counterclockwise until you hear a click.
2. After unlocking the roller brush, remove it from the mini electric brush, then rinse and clean the roller brush.
3. After washing, allow the roller brush to dry thoroughly by standing it upright in a well-ventilated area for at least 24 hours [24-hour-drying].
4. Once the roller brush is dry, reinstall it by following the disassembly steps in reverse.

Cleaning the Water Tank and Mop Pad

Notes:

• When the vacuum cleaner is charging or not in use, remove the water tank and drain any remaining water to prevent mildew or lingering odor.
• A worn or damaged mop pad that no longer sticks to the water tank should be replaced to ensure optimal cleaning performance.

1. Slide the water tank down to detach it from the smart high torque brush bar.
2. Empty the water tank.
3. Remove the mop pad from the water tank.
4. Clean and dry the mop pad. Allow it to dry for at least 24 hours [24-hour-drying].

Water Dispenser Filter

The water dispenser filter should be replaced if the water tank dispenses water too slowly or becomes clogged. To ensure optimal mopping effectiveness, it is recommended to replace water dispenser filters once every 3 to 6 months, depending on water quality and frequency of use.

1. Use your fingers to slide out old water dispenser filters on the left and right sides of each slot.
2. Insert the new water dispenser filters and check to ensure they are installed correctly.

Battery Pack

The vacuum cleaner contains a removable rechargeable lithium-ion battery pack with a limited number of recharge cycles. After extended use, the battery pack may no longer hold a charge, indicating it has reached the end of its life cycle and needs replacement.

1. Press down the battery pack release button and slide the battery pack to the right [right-arrow] to remove it.
2. Install the new battery pack.

Specifications

Vacuum Cleaner

Smart High Torque Brush Bar

Mini Electric Brush

Charger

Rechargeable Lithium-ion Battery Pack

WEEE Information

[wEEE-symbol] All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

The lithium-ion battery pack contains substances that are hazardous to the environment. Before disposing of the vacuum cleaner, please first remove the battery pack, then discard, or recycle it in accordance with local laws and regulations of the country or region it is used in.

FAQ

Troubleshooting

If the vacuum cleaner is not working properly, the screen display will show an error message. Refer to the troubleshooting table below for solutions based on the error message.

Downloads

Mi Vacuum Cleaner G10 Manual – Download [optimized]

Mi Vacuum Cleaner G10 Manual – Download

Related Manuals

• Mi Vacuum Cleaner G9 Manual
• Mi Handheld Vacuum Cleaner Manual
• Mi Vacuum Cleaner Light Manual
• Mi Vacuum Cleaner mini User Manual SSXCQ01XY
• Mi 10000mAh Mi 18W Fast Charge Power Bank 3 User Manual
• Mi A2 Manual