BLACK&DECKER MATRIX QUICK CONNECT SYSTEM INFLATOR ATTACHMENT
Model: BDCMTHPI-XE
For Australia & New Zealand
Website: www.blackanddecker.com.au
Parts and Features
Description of the diagram showing the inflator attachment and its components:
- 1. Inflator attachment body
- 2. Air hose
- 3. Universal valve adaptor with lever
- 4. Pressure gauge
- 5. Accessory storage compartment
Intended Use
The Black & Decker multi-purpose tool, equipped with this inflator head, is designed for a wide range of DIY applications. It is intended for inflating bike tires, balls, rafts, swimming pool floats, air mattresses, and similar items around the home.
Recommended maximum continuous duty cycle at 65 psi: 2 minutes operation followed by 5 minutes rest.
This tool is intended for consumer use only.
Safety Instructions
General Power Tool Safety Warnings
⚠️ WARNING! To reduce the risk of injury, the user must read the instruction manual.
⚠️ WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions listed below may result in electric shock, fire, and/or serious injury.
⚠️ WARNING! Read all safety warnings and all instructions provided with your power unit (BDCDMT108-XE, BDCDMT180-XE) before using this accessory.
⚠️ WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.
Specific Hazard Warnings
⚠️ WARNING: Risk to breathing. The compressed air from your inflator is not safe for breathing. Never inhale air from your inflator or from a breathing device connected to the inflator.
⚠️ WARNING: Risk of bursting. Too much air pressure causes a hazardous risk of bursting. Check the manufacturer's maximum pressure rating for objects being inflated. Do not leave the inflator running unattended. It could burst tires or other items.
⚠️ WARNING: Risk of unsafe operation. Do not modify or attempt to repair. Never drill into, weld, or make any modifications to the inflator or its attachments. Operate only with the accessories included or air handling parts acceptable for not less than 170 psi. The use of any accessory not recommended for use with this tool could be hazardous. Never engage in "horseplay." High pressure air is dangerous. Do not direct air-flow at yourself or others.
⚠️ WARNING: Always leave the valve adaptor lever open when not in use.
⚠️ WARNING: RISK OF FIRE: The inflator can become hot during use. Allow the inflator to cool for 30 minutes before storing away.
Symbols
The label on your tool may include the following symbols. The symbols and their definitions are as follows:
| V | volts | A | amperes |
| Hz | hertz | W | watts |
| min | minutes | ~ | alternating current |
| [DC] | direct current | no | no load speed |
| [Class II Construction] | Class II Construction (double insulated) | .../min or rpm | revolutions or reciprocation per minute |
| [respiratory protection] | Use proper respiratory protection | [hearing protection] | Use proper hearing protection |
| [eye protection] | Use proper eye protection |
Operating Instructions
⚠️ WARNING: Risk of Bursting. Too much air pressure causes a hazardous risk of bursting. Check the manufacturer's maximum pressure rating for objects being inflated.
⚠️ WARNING: Shock hazard. Under no circumstances should this product be used near water.
⚠️ WARNING: Risk of lacerations or burns. Do not touch the work piece or accessory immediately after operating the tool, as they can become very hot. Handle carefully. Always allow accessories and work piece to cool before handling.
⚠️ WARNING: To reduce the risk of injury, turn off and remove the battery from the tool or disconnect the plug from the power source before making any adjustments or removing or installing attachments or accessories. Remove any accessory from the attachment before removing or installing the attachment.
IMPORTANT: Refer to the Power Unit instruction manual before operating this tool for all safety warnings and details on installing and removing attachments.
Inflating
- To switch the tool on, press the variable speed switch on the power unit. The tool speed depends on how far you press the switch.
- To switch the tool off, release the variable speed switch.
NOTE: This attachment only operates in the forward direction; the forward/reverse slider of the Power Unit should not be able to be switched to reverse.
Valve Adaptor
- Position the lever (A1) of the valve adaptor straight up.
- As shown in Figure A, push the valve adaptor down over the threaded section of the valve stem, or over one of the nozzles provided with your inflator.
- When the adaptor is down all the way, press the lever down to lock it in place.
- To release the adaptor from a valve stem or accessory nozzle, lift the lever straight up and pull the adaptor off.
- Operate your Inflator only with the nozzles included.
- Make sure that the universal valve adaptor lever is firmly locked down in place before turning the Inflator on.
NOTE: Many inflatables, especially air mattresses, have an internal flap that prevents air loss during inflation. Unless this flap is displaced by the nozzle, the mattress will not inflate. Push the nozzle firmly into the valve to ensure that you push this flap out of the way.
Hose and Pressure Gauge
NOTE: Never carry the inflator by the hose.
- The pressure gauge, located on the hose, provides a pressure reading in P.S.I. (pounds per square inch) as well as in Bar pressure units.
- For tire inflating, it is recommended that the pressure reading be verified by checking with a separate tire gauge.
- To obtain a more accurate pressure measurement, turn the Inflator OFF when reading the gauge.
⚠️ WARNING: Do not leave inflator running unattended. It could burst tires or other items.
Nozzle Usage
- Place the valve adaptor over the stem of the nozzle as indicated in the "Valve Adaptor" section above.
- Place the needle nozzle or beach ball nozzle into the object to be inflated.
- When finished, remove the nozzle from the valve adaptor and store in the accessory storage compartment.
Maintenance
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance, and adjustments (other than those listed in this manual) should be performed by a qualified service dealer or other qualified service personnel.
Accessories
⚠️ WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
Additional attachments and accessories for use with this tool are available at extra cost from your local Sears store or Sears service center.
If you need assistance regarding accessories, please call: 1800-444-224
Troubleshooting
| Problem | Possible Cause | Possible Solution |
|---|---|---|
| Attachment will not start. | Attachment is not secured. | Make certain the attachment is fully pushed into the Power Unit. |
NOTE: Refer to the Power Unit instruction manual for troubleshooting solutions regarding operation of the Power Unit.
Technical Data
When operated with 18V MATRIX unit:
| Inflator | BDCMTHPI-XE |
|---|---|
| PSI | 80 PSI Continuous 100 Peak PSI |
| Weight | 467g |
Contact Information
Australia & New Zealand
Stanley Black & Decker
82 Taryn Drive, Epping, VIC 3076 Australia
Tel. 1800 444 224 (Aust) or Tel. 0800 339 258 (NZ)
Document Revision: 90589518 REV-0, Date: 07/2012
