Allen + Roth Hardtop Gazebo

Product Specifications

Package Contents

Hardware Contents

Safety Information

DANGER: This unit is heavy! Do not assemble this item alone.

CAUTION:

• Always keep children under close supervision while they are using or around this product. Never leave children unattended.
• Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury, possibly even death.
• Two people are required for this assembly.
• Some parts may contain sharp edges. Wear protective gloves if necessary.
• When assembling and using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please read all instructions before assembly and usage.
• This product is intended for domestic, outdoor use only.
• The product should be placed on flat, horizontal ground.
• Ensure enough clearance around the product. Before assembling the product, find level ground not less than 6' (18 m) away from any structures or obstructions such as fences, garages, houses, overhanging branches, laundry lines, or electrical wires.
• The gazebo must be anchored with stakes onto the ground for added safety. It cannot be permanently attached to a concrete floor or platform. Do not assemble the gazebo on sandy, muddy or loose soil as stakes do not have enough anchorage in these types of soil.
• In case you set up more than one gazebo, keep a minimum distance of 10' (3 m) between the gazebos.
• Any assembly or maintenance of the product must be carried out by adults only.
• Arrange necessary manpower when assembling or moving the product.
• Keep children and pets away while setting up the gazebo.
• Check all nuts and bolts periodically for tightness. When required, tighten them again.
• Repairing and replacing parts should be done by a qualified technician.
• This gazebo is intended for decorative and sunshade purposes only, and it is not designed to withstand harsh weather, including high winds, rain, and snow.
• Always remove the canopy in heavy wind conditions; otherwise, it might tip over and cause damage to the product or injuries to passersby.
• Always ensure that the roof canvas is tensioned to avoid water accumulation on the roof. Remove accumulated water on the roof immediately, or disassemble the gazebo in order to avoid damages.
• If the product will not be used for a longer period (e.g., winter time), it should be stored in a clean, dry environment.
• Do not light any fires inside or near the product!
• Stay calm if fire breaks out. Search for the nearest exit. Do not return to the gazebo before firemen allow you to do so.
• Do not hang any weights on the roof frame.
• Do not climb onto the roof of the gazebo. Falling off the gazebo can result in serious injury.
• Retain the original packaging to store the gazebo.

Preparation

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 3 Hours

Note: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts.

Assembly Instructions

Step 1: Attach Post Legs to Base

Insert Post Leg (A) into Foot Plate Cover (B1). Then, insert Foot Plate (B2) into Post Leg (A). Secure the assembly using one M6 x 15 mm Bolt (BB). Repeat this process for all four legs.

Hardware Used:

• M6 x 15 mm Bolt (BB): 8 pcs

Step 2: Connect Short Side Beams

Install Short Side Left Beam (C1) into Short Side Right Beam (C2). Connect them using two M6 x 10 mm Bolts (AA) and two M6 x 15 mm Bolts (BB). Repeat this process for the other side. Note: Do not install bolts in the two outer holes marked with 'X's.

Hardware Used:

• M6 x 10 mm Bolt (AA): 4 pcs
• M6 x 15 mm Bolt (BB): 4 pcs

Step 3: Connect Long Side Beams

Install Long Side Left Beam (C3) into Long Side Right Beam (C4). Connect them using two M6 x 10 mm Bolts (AA) and two M6 x 15 mm Bolts (BB). Repeat this process for the other side.

Hardware Used:

• M6 x 10 mm Bolt (AA): 8 pcs
• M6 x 15 mm Bolt (BB): 4 pcs

Step 4: Attach Beam Center Covers

Place Beam Center Cover (D) in the center of the previously assembled beams (C1, C2, C3, C4). Secure each cover using three M6 x 15 mm Bolts (BB). Repeat for all four beam centers.

Hardware Used:

• M6 x 15 mm Bolt (BB): 12 pcs

Step 5: Attach Beams to Post Legs

Place the assembled beams (C1, C2) onto Post Legs (A). Secure each beam to the post legs using two M6 x 45 mm Bolts (EE) and two Bolts (KK). Repeat for all four corners.

Hardware Used:

• M6 x 45 mm Bolt (EE): 8 pcs
• Bolt (KK): 4 pcs

Step 6: Attach Long Side Beams to Post Legs

Place the assembled beams (C3, C4) onto Post Legs (A). Secure each beam to the post legs using two M6 x 45 mm Bolts (EE) and two Bolts (KK). Repeat for all four corners.

Hardware Used:

• M6 x 45 mm Bolt (EE): 8 pcs
• Bolt (KK): 4 pcs

Step 7: Square the Gazebo Frame

Squaring the gazebo frame is crucial for proper assembly. Measure the distances between the outside corners of each leg post in the following orders: 1 to 2, 3 to 4, 1 to 3, 2 to 4, 1 to 4, and 2 to 3. Ensure all these measurements are the same. Adjust the legs as needed until the frame is square. Once measurements are consistent, proceed to Step 8.

Step 8: Secure Corbels

Attach the Corbel (E) to the beams (C1, C2, C3, C4) using two M6 x 15 mm Bolts (BB) for each corbel. Repeat for all eight corbels.

Hardware Used:

• M6 x 15 mm Bolt (BB): 16 pcs

Step 9: Attach Beam Corner Covers

Secure the Beam Corner Cover (F) to the four corners of the frame using three M6 x 15 mm Bolts (BB) for each corner. Repeat for all four corners.

Hardware Used:

• M6 x 15 mm Bolt (BB): 16 pcs

Step 10: Install Studs and Connectors

Install Stud (LL) into Corner Rafter (G). Secure the Connector (H) to the Corner Rafter (G) using two M6 x 15 mm Bolts (BB). Repeat for all four corner rafters.

Hardware Used:

• M6 x 15 mm Bolt (BB): 8 pcs
• Stud (LL): 4 pcs

Step 11: Assemble Top Frame Connections

Place Small-Top Tube 1 (J1) and Small-Top Tube 2 (J2) between Top Frame Connection 1 (I1) and Top Frame Connection 2 (I2). Secure using M6 x 35 mm Bolts (DD), 6.5 x 6 x 1.0 mm Washers (HH), and 10 mm Nuts with M6 Threads (GG). Ensure screw holes are facing correctly. Repeat for all four top frame connections.

Hardware Used:

• M6 x 35 mm Bolt (DD): 16 pcs
• 6.5 x 6 x 1.0 mm Washer (HH): 16 pcs
• 10 mm Nut with M6 Threads (GG): 16 pcs

Step 12: Attach Corner Rafters to Frame

Secure the lower end of Corner Rafter (G) to Post Leg (A) using two M6 x 55 mm Bolts (FF), two 6.5 x 6 x 1.0 mm Washers (HH), and two 10 mm Nuts with M6 Threads (GG). Attach the top of Corner Rafter (G) between Top Frame Connection 1 (I1) and Top Frame Connection 2 (I2), securing with two M6 x 35 mm Bolts (DD), two 6.5 x 6 x 1.0 mm Washers (HH), and two 10 mm Nuts with M6 Threads (GG). Repeat for all four corner rafters.

Hardware Used:

• M6 x 35 mm Bolt (DD): 8 pcs
• M6 x 55 mm Bolt (FF): 8 pcs
• 6.5 x 6 x 1.0 mm Washer (HH): 16 pcs
• 10 mm Nut with M6 Threads (GG): 16 pcs

Step 13: Install 2nd Tier Corner Rafters and Tubes

Secure 2nd Tier Corner Rafter (L) into Bottom Cover (K) using two M6 x 15 mm Bolts (BB). Secure Small-Top Short Tube (M1) and Small-Top Long Tube (M2) to the 2nd Tier Corner Rafter (L) using two M6 x 15 mm Bolts (BB) each. Repeat for all four corners.

Hardware Used:

• M6 x 15 mm Bolt (BB): 12 pcs

Step 14: Attach Hooks to Bottom Cover

Screw Hook (N) into Bottom Cover (K). Repeat for both hooks.

Hardware Used:

• Hook (N): 2 pcs

Step 15: Install 2nd Tier Roof Panels

Lay 2nd Tier Short Side Roof Panel (O1), 2nd Tier Long Side Left Roof Panel (O2), and 2nd Tier Long Side Right Roof Panel (O3) onto the frame. Secure them using two M6 x 15 mm Bolts (BB) for each panel. Repeat for all second tier roof panels.

Hardware Used:

• M6 x 15 mm Bolt (BB): 16 pcs

Step 16: Secure 2nd Tier Corner Caps and Top Cover

Secure 2nd Tier Corner Cap (P) to the roof panels using two M6 x 35 mm Bolts (DD) and two 7 x 15 x 2.0 mm Washers (II). Secure 2nd Tier Top Cover (Q) to the top of the roof panels using two M6 x 45 mm Bolts (EE) and two 7 x 15 x 2.0 mm Washers (II). Repeat for all corners and the top cover.

Hardware Used:

• M6 x 35 mm Bolt (DD): 4 pcs
• M6 x 45 mm Bolt (EE): 2 pcs
• 7 x 15 x 2.0 mm Washer (II): 6 pcs

Step 17: Attach Upper Frame to Lower Frame

Place the frame assembled in Step 16 onto the frame assembled in Step 12. Secure them using one M6 x 15 mm Bolt (BB) at each connection point. Repeat for all four connection points.

Hardware Used:

• M6 x 15 mm Bolt (BB): 4 pcs

Step 18: Unfold Netting

Unfold Small-Top Netting 1 (R1) and Small-Top Netting 2 (R2). Repeat for both nets.

Step 19: Secure Small-Top Netting 1

Secure Small-Top Netting 1 (R1) to the short side beams using two M6 x 15 mm Bolts (BB) at each attachment point. Repeat for both netting pieces.

Hardware Used:

• M6 x 15 mm Bolt (BB): 8 pcs

Step 20: Secure Small-Top Netting 2

Secure Small-Top Netting 2 (R2) to the long side beams using two M6 x 15 mm Bolts (BB) at each attachment point. Repeat for both netting pieces.

Hardware Used:

• M6 x 15 mm Bolt (BB): 8 pcs

Step 21: Attach Rafter Branch Assemblies

Secure the Short Side Rafter Branch Assembly (S1) and Long Side Rafter Branch Assembly (S2) to Small-Top Tube 1 (J1) and Small-Top Tube 2 (J2) using three M6 x 15 mm Bolts (BB) for each assembly. Repeat for all four assemblies.

Hardware Used:

• M6 x 15 mm Bolt (BB): 12 pcs

Step 22: Install Short Side Center Roof Panels

Secure the Short Side Center Roof Panel (T1) to the short side beam using two M6 x 25 mm Bolts (CC) and two 7 x 15 x 2.0 mm Washers (II). Repeat for both panels.

Hardware Used:

• M6 x 25 mm Bolt (CC): 4 pcs
• 7 x 15 x 2.0 mm Washer (II): 4 pcs

Step 23: Install Long Side Roof Panels

Secure Long Side Left Roof Panel (T2) and Long Side Right Roof Panel (T3) to the long side beam using two M6 x 25 mm Bolts (CC) and two 7 x 15 x 2.0 mm Washers (II). Repeat for both panels.

Hardware Used:

• M6 x 25 mm Bolt (CC): 4 pcs
• 7 x 15 x 2.0 mm Washer (II): 4 pcs

Step 24: Install Middle Roof Panels

Install Left Middle Roof Panel (Long & Short Side) (T4) and Right Middle Roof Panel (Long & Short Side) (T5) into the Short Side Center Roof Panel (T1), Long Side Left Roof Panel (T2), and Long Side Right Roof Panel (T3). Secure using two M6 x 25 mm Bolts (CC) and two 7 x 15 x 2.0 mm Washers (II) for each panel. Repeat for all middle roof panels.

Hardware Used:

• M6 x 25 mm Bolt (CC): 8 pcs
• 7 x 15 x 2.0 mm Washer (II): 8 pcs

Step 25: Install Small Roof Panels

Install Left Small Roof Panel (Long & Short Side) (T6) and Right Small Roof Panel (Long & Short Side) (T7) into the Left Middle Roof Panel (T4) and Right Middle Roof Panel (T5). Secure using two M6 x 15 mm Bolts (BB) for each panel. Repeat for all small roof panels.

Hardware Used:

• M6 x 15 mm Bolt (BB): 8 pcs

Step 26: Attach Both Side Pressers

Attach Both Side Presser (U1) to the roof structure. Secure each presser using three M6 x 15 mm Bolts (BB). Repeat for all eight pressers.

Hardware Used:

• M6 x 15 mm Bolt (BB): 24 pcs

Step 27: Install Middle of Presser 1

Install Middle of Presser 1 (U2) onto the long roof panels. Secure using two M6 x 15 mm Bolts (BB) for each presser. Repeat for both pressers.

Hardware Used:

• M6 x 15 mm Bolt (BB): 4 pcs

Step 28: Install Middle of Presser 2

Install Middle of Presser 2 (U3) onto the short roof panels. Secure using two M6 x 15 mm Bolts (BB) for each presser. Repeat for both pressers.

Hardware Used:

• M6 x 15 mm Bolt (BB): 4 pcs

Step 29: Secure Roof Corner Caps

Secure Roof Corner Cap (V) to the roof corners using two 10 mm Nuts with M6 Threads (GG), two 7 x 15 x 2.0 mm Washers (II), and two Nut Caps (JJ) for each corner. Repeat for all four corners.

Hardware Used:

• 10 mm Nut with M6 Threads (GG): 8 pcs
• 7 x 15 x 2.0 mm Washer (II): 8 pcs
• Nut Cap (JJ): 8 pcs

Step 30: Stake Down Foot Plates

Lift the Foot Plate Cover (B1) and insert Stake (MM) into the ground beneath it. This step is for securing the gazebo to grass or soft ground. Repeat for all four legs.

Hardware Used:

• Stake (MM): 8 pcs

Care and Maintenance

• Be careful to never allow water to build up in frames, as this will cause corrosion and freeze damage in cold climates.
• Wash all frames with a solution of mild soap and water. Rinse with clean water and dry with a soft absorbent cloth towel.
• Frames can be treated with a liquid wax for maximum protection against UV rays and/or salty, damp air.
• Canopy may be cleaned by hand with a solution of soap and water with a clean water rinse. Never machine wash the canopy as this will result in shrinkage or damage. Never use a commercial or home dryer to tumble dry fabric goods.
• Do not use bleach or solvents to clean any product, as this will void the warranty.

Warranty

3-Year Limited Warranty

For a period of three (3) years after date of purchase, the Manufacturer will either repair or replace defective components in accordance with this Limited Warranty. This warranty is between the Manufacturer and the original purchaser and is valid only when accompanied by the original purchaser's sales receipt showing the original date of purchase and location of purchase. Replacements under this warranty revert back to the date of original purchase for future warranty.

The Manufacturer or its authorized dealer can accept or reject warranty claims based on its findings. This warranty applies to normal residential use only and is not intended for commercial use. The Manufacturer may make substitutions as required of materials, components, and sub-components of comparable value and utility. This warranty is limited to product repair or replacement (to be determined solely by the Manufacturer). Warranty return is limited to only the single affected component.

This limited warranty covers only manufacturing defects and does not cover normal wear and tear, damage due to acts of nature (such as, but not limited to freezing or high winds), abuse or misuse, including chemical damage from suntan oil or other chemicals, exposure to extreme heat or cold, abrasion or excessive weight.

This product is intended to be used in standard installations only. This warranty is void if the product is not used for its intended purpose. The Manufacturer disclaims liability for any aspect of installation and any inconvenience caused by a defective part or component.

Certain items are not covered by this warranty. These include, but are not limited to the following:

• Components subjected to abuse, including abuse intended to simulate failure.
• Damages caused by retailer, shipper, or installation crew (such as scratches, dents, tears, chips, etc).
• Any part which merely exhibits normal wear yet functions essentially as new, including chips, scratches, or stretching of materials and stitching.
• Tears, punctures, scratches, or any damage caused by improper installation or use.
• Damage to frames/welds resulting from improper assembly or exposure to water and/or sub-freezing temperatures is not covered. General frame rusting is not covered.
• Fading and/or discoloration of fabrics/cushions/straps/wicker resulting from exposure to the elements, chemicals, oils, fluids, or any other cause are not covered.
• Umbrella bases are not covered under any circumstances.
• Items sold "as is" or floor models.

To make a claim, call the toll-free number below. Please have available a copy of the original sales receipt along with a brief description of the problem. Please also provide your email address and daytime telephone or cell phone number. All items may be charged actual freight costs plus $15 for handling. Repairs or replacement will be made at the Manufacturer's option. Sales and use taxes, plus shipping and handling charges are the responsibility of the consumer.

THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER NEITHER MAKES NOR IS RESPONSIBLE FOR ANY OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED INCLUDING THOSE OF RETAILING DEALERS. THIS EXCLUSIVE REMEDY IS LIMITED TO RECEIPT OF A CREDIT IN CONNECTION WITH THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR COMPONENT DEEMED TO BE DEFECTIVE UNDER THE TERMS AND CONDITIONS AS STATED IN THIS WARRANTY. NEITHER THE PRODUCT MANUFACTURER NOR ITS AGENTS SHALL BE LIABLE IN ANY CASE FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY OR NEGLIGENCE EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, EXCEPT AS OTHERWISE MAY BE REQUIRED BY LAW, THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES OTHER THAN THE WARRANTY DESCRIBED HEREIN, AND ALL OTHER WARRANTIES, INCLUDING IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DISCLAIMED.