Offset Umbrella

Preparation

Before beginning assembly of the product, ensure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 40 minutes

No Additional Tools Required

Feeling Confident? Start Your Next Project

Visit lowes.com for more information.

Care and Maintenance

• Before using, clean the product completely with a soft, dry towel.
• When not in use, wipe free of any dirt or loose objects, wash with a mild solution of soap and water, rinse and dry completely.
• Do not use strong detergents or abrasive cleaners.
• Store the product in a cool, dry location away from sunlight.

Warranty

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING:

• Tighten each bolt firmly and properly. Do not completely tighten screws until all screws are started.
• Some parts may contain sharp edges. Wear protective gloves as necessary.
• Children under the age of 16 should not be engaged in the assembly, removal or disassembly of the product.
• Children under the age of 10 should be supervised by a competent adult while using this furniture.
• Please keep children out of the assembly area during assembly.
• This set is heavy, and may require two adults for safe assembly.
• Never use this product as a support. Do not shake, lean, or climb on the product at any time.

CAUTION:

• Retain these instructions for future reference.
• Paint on this product might peel off if it is hit or used improperly. Use and carry this item with care and apply touch-up paint (not included) when necessary.
• This outdoor furniture is designed and made for personal non-commercial use.
• This item should not be used as a toy or a tool.
• Do not locate the product near any heat source.

Installation Overview

Assembly Steps

1. Step 1: Assemble Base and Attach Pole
   Diagram shows attaching cross base legs (F) to the base (A) using bolts (DD) and washers (CC), secured with wrench (FF). Then, attaching support bracket (G) to base (A) with screws (EE) and wrench (FF). Finally, attaching pole (B) to base (A) using bolt (AA), washer (CC), screw (EE), and wrench (FF).

   Attach cross base legs (F) to the base (A) using bolts (DD) and washers (CC). Secure with wrench (FF). Attach support bracket (G) to the base (A) using screws (EE) and wrench (FF). Attach pole (B) to the base (A) using bolt (AA), washer (CC), screw (EE), and wrench (FF).

2. Step 2: Attach Crank Mechanism
   Diagram shows attaching the crank mechanism (C) to the pole (B).

   Attach the crank mechanism (C) to the pole (B).

3. Step 3: Attach Umbrella Ribs
   Diagram shows attaching umbrella ribs (D) to the crank mechanism (C) and pole (B).

   Attach umbrella ribs (D) to the crank mechanism (C) and pole (B).

4. Step 4: Attach Canopy
   Diagram shows attaching the canopy (E) to the umbrella ribs (D).

   Attach the canopy (E) to the umbrella ribs (D).

5. Step 5: Connect Canopy to Crank Mechanism
   Diagram shows connecting the canopy (E) to the crank mechanism (C).

   Connect the canopy (E) to the crank mechanism (C).

6. Step 6: Attach Crank Handle
   Diagram shows attaching the crank handle (J) to the crank mechanism (C).

   Attach the crank handle (J) to the crank mechanism (C).

7. Step 7: Operate Umbrella (Open/Close)
   Diagram shows an ON-OFF/ENCENDIDO-APAGADO indicator with a crank handle symbol and an arrow indicating operation.

   Use the crank handle to open and close the umbrella.

8. Step 8: Final Tightening
   Diagram shows tightening bolts with wrench (FF) and nuts (GG).

   Once all connections are made, tighten all bolts with FF and GG.