HAUGA High Cabinet Assembly Instructions

Important Safety Information

⚠️ WARNING: Children have died from furniture tipover. To reduce the risk of furniture tipover:

• ALWAYS install the anti-tip device provided.
• NEVER place a TV on this product.
• NEVER allow children to stand, climb, or hang on any drawers, doors, or shelves.
• NEVER open more than one drawer at a time.
• Place heaviest items in the lowest drawers.

Read and follow each step of the instruction carefully.

Tools Required

• Screwdrivers (Phillips and Flathead)
• Hammer
• Ladder
• Drill

Drill bit sizes: Ø 8 mm (5/16"), Ø 3 mm (1/8")

Parts and Hardware

The following parts and hardware are included:

• Dowels: 34x (151707), 34x (151708)
• Cam Bolts: 14x (10039873), 30x (10093081), 39x (10093082), 4x (10051022), 4x (10040039)
• Cam Locks: 2x (10039878), 20x (10051650), 20x (10051660)
• Hinges: 4x (10093081), 4x (10093082)
• Knobs: 6x (101345)
• Screws: 2x (151708), 2x (158568), 2x (153548), 18x (119976), 2x (10052019), 30x (144574), 22x (144575), 2x (10050715), 2x (10042135), 2x (10070233)
• Brackets: 2x (109049)
• Wall Plugs: 2x (121714)
• Other hardware: 4x (106989), 4x (100823), 2x (10049270), 8x (120173)

Assembly Steps

Step 1: Assemble Base Frame

Connect the base panel to the side panels using dowels (151707, 151708) and cam bolts/locks (e.g., 10039873, 10039878). Ensure a "CLICK!" sound confirms secure locking.

Step 2: Attach Side Panels

Attach the main side panels to the base and any intermediate panels using dowels and cam bolts/locks. Follow the sequence shown in the diagrams.

Step 3: Insert Back Panels

Slide the thin back panels into the grooves along the rear edges of the assembled frame.

Step 4: Assemble Lower Cabinet Box

Continue building the lower section of the cabinet by connecting panels with dowels and cam locks. Ensure all connections are tight.

Step 5: Attach Shelf Supports

Insert shelf supports (e.g., 151707) into the pre-drilled holes inside the cabinet sections at desired heights.

Step 6: Mount Hinges to Cabinet

Attach hinge components (e.g., 10093081, 10093082) to the designated mounting points on the cabinet frame using screws (e.g., 144574).

Step 7: Install Drawer Slides

Attach drawer slide runners (e.g., 101345) to the sides of the cabinet structure using screws.

Step 8: Assemble Doors

Attach the other half of the hinges to the doors. Mount door handles (101345) to the doors using screws (e.g., 119976).

Step 9: Mount Doors to Cabinet

Attach the doors to the cabinet by connecting the hinge parts. Adjust hinges for proper door alignment and gap.

Step 10: Assemble Upper Cabinet Section

Repeat the process of connecting panels, dowels, and cam locks to build the upper section of the cabinet.

Step 11: Connect Upper and Lower Sections

Carefully lift and align the upper cabinet section onto the lower section. Secure them together using the provided hardware.

Step 12: Attach Top Panel

Install the top panel of the cabinet, securing it with cam locks and bolts.

Step 13: Install Internal Fittings

Attach any internal mechanisms, such as soft-close fittings or drawer runners, using the specified screws (e.g., 10051650, 10051660).

Step 14: Place Shelves

Insert the shelves onto the previously installed shelf supports.

Step 15: Attach Wall Mounting Brackets

Secure the wall mounting brackets (109049) to the top rear of the cabinet using screws (e.g., 106989, 100823).

Step 16: Position Cabinet

Move the assembled cabinet to its final desired location against the wall.

Step 17: Mark Wall for Mounting

Align the cabinet and mark the wall through the holes in the mounting brackets.

Step 18: Prepare Wall for Anchors

Drill holes in the wall at the marked locations according to the wall type (A, B, or C) and insert wall plugs (121714) if required.

• Type A/B (Hollow Walls): Drill Ø 8 mm, ~70 mm deep (A) or ~30 mm deep (B).
• Type C (Solid Wood): Drill Ø 3 mm.

Step 19: Secure Cabinet to Wall

Attach the wall mounting brackets to the wall using appropriate screws (e.g., 100823, 109048) and wall plugs. Ensure the cabinet is firmly secured.

Step 20: Final Door Adjustments

Make final adjustments to the doors using the hinge screws to ensure they are level, aligned, and open/close smoothly.