URMET 1099/211B Cloud Camera Series Quick Guide

Product Overview

This document provides a quick guide for the URMET 1099/211B Cloud Camera Series. The camera is designed for smart WiFi IP surveillance applications.

Supported product variants include:

• TELECAMERA SMART WiFi IP 3M PT 3.6MM
• WiFi 3M IP SMART CAMERA PT 3.6MM
• WiFi 3M IP SMARTKAMERA PT 3.6MM
• CAMÉRA SMART WiFi IP 3M PT 3.6MM

For more information, visit www.urmet.com.

Camera Description and Specifications

The camera is a compact, white, pan-and-tilt (PT) unit with approximate dimensions of 111.45mm height, 73.21mm width (front), and 73.05mm depth (side).

Key features include:

• Camera lens at the top.
• Circular LED indicator at the front base.
• Micro SD card slot for recording.
• Recessed Reset button.
• Power input port.

Radio Frequency Band: 2380MHz~2673.5MHz

Maximum Radio Power Transmitted:

• Max EIRP 17.41 dBm @ 802.11b
• Max EIRP 17.14 dBm @ 802.11g
• Max EIRP 15.82 dBm @ 802.11n (HT20)
• Max EIRP 15.92 dBm @ 802.11n (HT40)

1 Warnings and Precautions

Precautions for Use

• Ensure the device is intact after unpacking.
• Disconnect the device from the power supply before cleaning or maintenance.
• Do not use spray products for cleaning.
• Verify that the operating temperature is within the indicated range and the environment is not excessively humid.
• In case of failure or malfunction, disconnect power via the main circuit breaker.
• The device should only be opened by qualified technical personnel.
• Contact an authorized service center for repairs.

Installation Specifications

• It is recommended to install a suitable disconnect and protection switch upstream of the device.
• Before connecting to the power supply, ensure the rating plate data matches the distribution network specifications.

Installation Precautions

• To prevent overheating, place the device in a well-ventilated position.
• Avoid environments like seashores or very dusty locations, as they can accelerate corrosion or compromise optimal operation.
• Do not install near heat sources (radiators, hot air ducts), in direct sunlight, or in rooms with excessive dust, mechanical vibrations, or impacts.
• Consider the device's operating temperature range when selecting an installation location. Do not install over other heat-emitting devices.
• Allow approximately three hours for the device to adapt to a new environment (temperature, humidity) after moving it from a cold to a warm place, or vice versa.

Video Recording

• This device is designed for transmitting and recording video images, not as an anti-theft system. URMET S.p.A. is not responsible for losses or damages resulting from theft.
• Perform a test recording to verify correct functionality. URMET S.p.A. is not responsible for data loss due to incorrect settings, usage, malfunction, or failure.
• The device contains precision electronic components; avoid impacts during recording as they may affect video quality.

Privacy and Copyright

• The IP camera is designed for surveillance systems. Video recording is subject to local laws. Recording copyrighted images is prohibited.
• Users are responsible for complying with all local laws and regulations regarding video signal monitoring and recording. The manufacturer is not liable for any use of the product that does not comply with applicable norms.
• For more information, consult www.garanteprivacy.it.

Firmware and Network

Firmware Update

Periodically check the URMET website (www.urmet.com) in the product-specific section (Products > AREA VIDEOSORVEGLIANZA) for software and/or firmware updates. Enter the product code in the search field and navigate to DOCUMENTATION AND RESOURCES.

Network Connections

The camera can connect to a WiFi network via a mobile phone using the V-stream app. The device supports a limited number of "unicast" connections, allowing up to 3 remote devices to view the video stream simultaneously, depending on available network bandwidth.

Reset Button

Press and hold the reset button for at least 3 seconds to completely reset the camera to factory default settings.

EU Declaration of Conformity

URMET S.p.A. declares that the radio equipment type: camera 1099/211B complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: www.urmet.com.

Installation and Setup

Installation Steps

1. Before installation, ensure all units to be connected are powered off. If installing multiple cameras on the same network, it is advisable to install and configure them one at a time.
2. Connect the camera to the network. It is recommended to ensure the WiFi signal strength received by the camera is 60 or higher.
3. Position the camera on a wall or other flat surface.
4. For recording on a Micro SD card (not included), insert the memory card into the slot when the camera is powered off. Power on the camera and use the app to format the card before starting the recording function.

Wi-Fi Network Configuration

Upon first power-on, the camera operates in Access Point (AP) mode. To connect it to a WiFi network, download the URMET V-Stream app to your mobile phone and refer to the quick setup guide for configuration.

Important Note: By default, the camera automatically sets the date and time by retrieving this information from the internet each time it is powered on. If the camera restarts without internet access, the correct date and time may not be guaranteed, potentially compromising SD memory recordings.

Product Disposal (WEEE)

The crossed-out wheeled bin symbol ♻️ on the product or its packaging indicates that the product must not be disposed of with ordinary household waste at the end of its useful life.

Users must hand over waste equipment to designated municipal collection centers for the separate disposal of electrical and electronic waste. Alternatively, the device can be returned to the retailer when purchasing an equivalent new appliance.

Electronic products up to 25 cm in size can also be handed in for free disposal, without purchase obligation, at electronics stores with sales areas of over 400 m².

Proper separate collection for recycling, treatment, and environmentally compatible disposal of scrapped equipment helps prevent negative impacts on the environment and human health, and promotes the reuse and/or recycling of the materials the equipment is made of.

Further Resources

The quick guide and complete user manual are also available for download from the URMET website in the DOCUMENTATION AND RESOURCES section.

Customer Care

Italia: 011 23 39 810

Export Dept.: +39 011 24 00 250/256

URMET S.p.A.

Via Bologna, 188/C | 10154 Torino (ITALY)

www.urmet.com | info@urmet.com

MADE IN CHINA