Operation Guide ANALOG (HK-W)

To set the time

For Modules: 1362, 1398, 1770, 2799, 3378, 4370

Pull out the crown. Set the hands by rotating the crown. Push the crown back in on a time signal to resume timekeeping.

[crown]

To set the time

For Modules: 705, 706, 1300, 1311, 1330, 1344, 1360, 1399, 1747, 1771, 4394, 5049

1. When the second hand is at 12 o'clock, pull out the crown to stop it.
2. Set the hands by rotating the crown. Move the minute hand four or five minutes past the setting you want, and then back them up to the setting.
3. Push the crown back in on a time signal to resume timekeeping.

[crown]

To set the time

For Modules: 707, 708, 1331, 1332, 1342, 1345, 1346, 1787, 2717, 2718, 2719, 2725, 2731, 2748, 2749, 2783, 2784, 3363, 3711, 3712, 4393, 5025, 5044

1. When the second hand is at 12 o'clock, pull out the crown to the second click to stop it.
2. Set the hands by rotating the crown. Move the minute hand four or five minutes past the setting you want, and then back them up to the setting.
3. Push the crown back in on a time signal to resume timekeeping.

[crown]

[first click for day setting]

[normal position]

[second click for time setting]

To set the day

For Modules: 707, 708, 1331, 1332, 1342, 1345, 1346, 1787, 2717, 2718, 2719, 2725, 2731, 2748, 2749, 2783, 2784, 3363, 3711, 3712, 4393, 5025, 5044

Avoid setting the day between 8:00 p.m. and 2:00 a.m. The day may not change in the following day if you do.

1. Pull out the crown to the first click.
2. Set the day by rotating the crown.
3. Push the crown back in to its normal position.

[crown]

[first click for day setting]

[normal position]

To set the time

For Modules: 709, 1333, 1347, 3716

1. When the second hand is at 12 o'clock, pull out the crown to the second click to stop it.
2. Set the hands by rotating the crown. Move the minute hand four or five minutes past the setting you want, and then back them up to the setting.
3. Push the crown back in on a time signal to resume timekeeping.

[crown]

[second click for time setting]

To set the day and day of the week

For Modules: 709, 1333, 1347, 3716

Avoid setting the day and day of the week between 8:00 p.m. and 4:00 a.m. The day and day of the week may not change in the following day if you do.

1. Pull out the crown to the first click.
2. Set the day by rotating the crown counterclockwise.
3. Set the day of the week by rotating the crown clockwise. Confirm that the correct language (English or Spanish) is selected.
4. Push the crown back in to its normal position.

[first click for day, day of week setting]

[crown in normal position]

[Sunday 30]

[second click for time setting]

Elapsed Time Bezel

For watches with an elapsed time bezel: Rotate the elapsed time bezel to align the mark with the minute hand. After a certain amount of time has elapsed, read the graduation on the elapsed time bezel which the minute hand points to. The elapsed time is indicated.

[elapsed time bezel]

Screw Lock Crown

Some water resistant models are equipped with a screw lock crown.

With such models, you must unscrew the crown in the direction noted in the illustration to loosen it before you can pull it out. Do not pull too forcibly on such crowns.

Also note that such watches are not water resistant while their crowns are loosened. Be sure to screw the crowns back in as far as they will go after making any setting.