MUNBYN IMC40 Banknote Counter
Maintenance Manual
Version 1.00
Contents
1.0. How to disassemble machine
Notice: When you receive the package, open and check the packing list in the package.
Disassemble left side cover step by step as following:
Disassemble right side cover step by step as following:
Disassemble display step by step as following:
Disassemble mainboard step by step as following:
Disassemble detection table step by step as following:
Take the transit table step by step as following:
Disassemble the build-in printer step by step as following:
2.0. Machine explosive
Whole machine explosive
The printing head support 1 million times of printing, only need to change when the printing is not complete.
Do not disassemble or loose screw of this part no matter what.
Feeding block part set:
- Hopper guide
- Hopper guide
- Hopper guide mesh bar
- Lin cover
- Hopper guide gear
- Motor board
- Motor board holder
Display board set:
- Hopper guide plate
- Hopper sensor
- Display board set
- Key panel
- Display board
- Feeding gas screw
- Reverse roller
- Reverse roller set
- Note press roller set
IR board set:
- IR board set
- Path guide board
Reject block:
- Reject block
- Reject box
- Reject socket fixer
Front guide set:
- Transport roller
- Front guide plate
- Front guide plastic
- Detection roller
Front path guider set:
- Notes cross brace
- Front path guider plastic
- Vice belt roller
- Transport roller
- Main control board
Back path guide set:
- IR board
- Deck path guide plastic
- CIS
Detection table:
- IR board
- CIS board
- Spring
- Front passive roller set
- Back cover
Transit table:
- Transit roller
- Plastic table
Internal components:
- Propeller motor
- Impeller
- Circulate
- Motor board
- Stacker motor cover
- Stacker back
- Stacker sensor
- Iron house
- Encoder sensor cover
- Speed disk
- Encoder sensor
- Encoder sensor cover
- Electromagnetic fixture
- Toggle bill part
- Stator magnetic
Feeding and printing mechanism:
- Buzzzing roller
- Feeding roller
- Feeding motor
- Stacker rubber delivery roller
- Transmit motor
- Motor fixture
- Printer cover
4.0. Common Issue reference
Feeding issue
Problem Description: Machine happens feeding hardly, double error, chain error, skew error, jam issue, miss counted.
Reason: Feeding gap is not in a properly distance.
Solution: Adjust the feeding gap to the properly distance as following picture shows:
- 1. large feeding gap caused double and chain
- 2. Anti clockwise adjustment
- 3. just allow one banknote pass through
- 1. too less feeding gap caused feeding speed slow down
- 2. clockwise adjustment
- 3. just allow one banknote pass through
Electromagnetic issue
Problem Description: 1. Machine happens BC error 2. jam issue 3. PS2 4. PS3
Reason: Electromagnetic reaction problem.
Solution: 1. Check the shelf holder of electromagnetic if loosen 2. Check the electromagnetic itself can be movable 3. The plastic of toggle bill part if change of shape during using.
5.0. Error list & Trouble shooting
Feeding issue
| ERROR | REASON |
|---|---|
| E1: UV Error | Note doesn't have UV |
| E2: Double Error | Double or Multi notes passed together |
| E3: Chain Error | Double or Multi notes counted in chain |
| E4: Skew Error | Note counted skewed too much |
| E5: Full | Reject pocket or Stacker full |
| E6: Half note Error | The note is not complete |
| Interval Error | The distance between two notes passed by is too short |
| Width Error | The width of note incorrect |
| Signal T Error | Signal transport problem |
| Data Process Error | Data processing over time limit |
| Denomination Error | Denomination don't match with count set |
| Image Error | Counterfeit or Data recognize problem |
| Face Error | Face of note doesn't match with count set |
| Orientation Error | Orientation of note doesn't match with count set |
| DOI Error | Date of Issue for note doesn't match with count set |
| Version Error | Version of note doesn't match with count set |
| MT Error | Note has magnetic problem |
| MT2 Error | Note has magnetic problem |
| MG1 Error | Note has magnetic problem |
| MG2 Error | Note has magnetic problem |
| MG3 Error | Note has magnetic problem |
| MG4 Error | Note has magnetic problem |
| S.Skew Error | Super skew of note |
| IR Error | Note has IR (transmit and reflection) problem |
Display issue
Problem Description: 1. Machine display happens splash screen 2. white screen or no response when touching it The count remain O during counting.
Reason: 1. Display itself problem 2. Display board has unsolder problem 3. Mainboard problem.
Solution: 1. Replace the display 2. Replace the display board 3. Replace mainboard.
Mainboard issue
Problem Description: 1. Machine display happens splash screen 2. CIS calibration failed 3. Too much error happen 4. Mainboard error 5. Machine doesn't count.
Reason: Mainboard chip damaged or unsolder problem.
Solution: Replace the mainboard.
CIS issue
Problem Description: 1. All notes rejected 2. CIS calibration failed.
Reason: CIS or CIS cable damaged.
Solution: Replace CIS.
6.0. Fcc caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
7.0. Contact us
Email: support@munbyn.com (24-7 online support)
Website: www.munbyn.com (how-to videos, warranty details)
WhatsAPP: +86 18144898200
Skype: +1650 206 2250
MUNBYN provides 18 months warranty and lifetime free service. If you encounter any issues with the product, please contact the MUNBYN team to promptly receive troubleshooting tips or a replacement.
Scan the QR code for Facebook and WhatsApp online chat.
