MUNBYN IMC02 Counterfeit Detector User Manual

1.0 Overview

Thank you for purchasing MUNBYN products. The IMC02 is designed for efficient banknote counterfeit detection. This user manual provides operating steps and precautions to ensure accurate product usage and improve working efficiency. Please read this manual carefully before use. Contact MUNBYN for any issues.

MUNBYN reserves the right to change the contents of this user manual without notice.

1.1 Preface

This section is identical to 1.0 Overview.

1.2 Abbreviation

The following table lists abbreviations used in this manual:

2.0 Packing Open and Installation

2.1 Packing List

Upon receiving the package, please open and check the packing list:

2.2 Power Supply

DC Power: Connect the power adapter to a 110V or 220V outlet, then connect the terminal to the machine's DC12V input socket.

Lithium Battery (optional): When the battery is fully charged, the machine can operate without a power adapter.

3.0 Operating Instructions

3.1 Display Appearance

The display shows:

• Currency Type: e.g., USD
• Banknote Exit Direction: Indicates the direction of banknote exit.
• Number of Banknotes: Counts the total number of detected banknotes.
• Denomination: Shows the value of the detected banknote.

3.2 Turn On/Off the Machine

To Turn On: Switch the power button to 'ON'. The screen will light up and the machine will start self-testing. Upon successful self-test, the banknote count and denomination will display '0'.

To Turn Off: Switch the power button to 'OFF'. The screen will turn off, indicating the machine has been successfully powered down.

3.3 Button Functions

3.3.1. CUR/DIR

The CUR/DIR button is used to select the currency or the banknote exit direction.

3.3.1.1. Choosing the Currency

In detection mode, the IMC02 automatically recognizes the currency. The CUR/DIR button cannot be used to manually select currencies. In report mode, this button allows switching between currencies to view report details.

3.3.1.2. Choosing the Direction

Press and hold the button for approximately 2 seconds until a "di" sound is heard. Release the button to change the direction indicator. The direction is shown at the top of the display: 'Up' indicates the genuine banknote exits from the front, and 'Down' indicates it retreats into the feeding hopper.

3.3.2. REP/CLR

Press this button to view the count of each denomination. Press and hold for approximately 2 seconds to clear all records.

3.4. Inserting the Banknote Correctly

After detecting banknotes, press “REP / CLR” to enter report mode. The display will show the currency type, pieces of each denomination, and total value. You can switch to another currency by pressing “CUR / DIR”. If a banknote is fed while in report mode, the detector will automatically exit report mode.

Insert banknotes into the left side of the machine as shown in the figures. Incorrect insertion may cause the IMC02 to refuse the banknote or alert.

3.5. EUR/GBP Currency Detecting

To detect EUR or GBP currency, remove the banknote feeding limit block to accommodate larger banknotes.

4.0. Maintenance

4.1. Error Code

The following table lists error codes and recommended handling methods:

4.2. Inaccurate Detection of Currency Detector

Several factors can affect the accuracy of the currency detector:

• The banknote size is outside the IMC02 specification range.
• The banknote is damaged (e.g., missing corner, tape, hole, tear, or folded). Counting such bills is not recommended, as shown in Figure 4-1.

Other abnormal operations or foreign objects inside the IMC02. If this occurs, open the front cover to inspect and clean the internal sensors.

4.3. 'ADD' function settings

Follow these steps to enable or disable the 'ADD' function:

1. Press and hold 'CUR/DIP' and 'REP/CLR' simultaneously for 5 seconds to enter the selection interface.
2. Press and hold the 'CUR/DIP' and ‘REP/CLR' buttons simultaneously on the d_1 interface for 2 seconds to enter the function selection interface.
3. Press the 'CUR/DIP' button three times to switch the mode to P22. Then, press and hold 'REP/CLR' to change the value of P22. Setting P22 to '0' enables the Add function; setting it to '1' disables it.

Demo video available at: https://munbyn.biz/IMC02ADD

5.0. Technical Parameters

Contact Information

For any issues or inquiries, please contact MUNBYN:

• Email: support@munbyn.com
• Whatsapp: +86-17817881067

You can also scan the QR code for Facebook online chat.