YITAHOME Queen Size Bed Frame Assembly Instructions
Model: FTBFBF-0088, WNYF-V1
Assembly Recommendations
1. Two or more people are required for assembly. 2. To avoid squeaking, please tighten the bolts all the way. An electric drill is recommended for the assembly. 3. Professional installation is highly recommended.
Parts List
Components
| Item No. | Description | Qty. |
|---|---|---|
| A | Headboard panel (tall, with decorative top) | 1 pc |
| B | Footboard panel | 1 pc |
| C | Side panel connector/bracket | 1 pc |
| D | Side panel (vertical) | 1 pc |
| E | Side rail (long, horizontal) | 1 pc |
| F | Side rail (long, horizontal) | 1 pc |
| G | Side rail (long, horizontal) | 1 pc |
| H | Side rail (long, horizontal) | 1 pc |
| I | Center cross support bar | 1 pc |
| J1 | Shorter center cross support bar | 1 pc |
| J2 | Shorter center cross support bar | 1 pc |
| K | Vertical support post | 3 pcs |
| L | Bed leg | 2 pcs |
| M | Angled support bracket | 1 pc |
| N1 | Slats (bed base support) | 1 pc |
| N2 | Slats (bed base support) | 1 pc |
Hardware
| Item No. | Description | Qty. |
|---|---|---|
| O | Casters (wheels) | 16 pcs |
| P | Drawer slide hardware | 4 pcs |
| Q | Corner bracket | 8 pcs |
| R | Drawer support bracket | 4 pcs |
| S | Drawer base/support panel | 4 pcs |
| T | Bolt/Screw (specific head) | 4 pcs |
| 1 | M8x40mm bolt | 16 pcs |
| 2 | M8x20mm bolt | 10 pcs |
| 3 | M8x55mm bolt | 5 pcs |
| 4 | M6x13mm screw | 20 pcs |
| 5 | M8x30mm screw | 4 pcs |
| 6 | Allen wrench | 1 pc |
| U | USB/Type-C power module | 1 pc |
Assembly Steps
Step 1
Attach the two Side Panels (D) to the Headboard Panel (A) using Connectors (C) and Bolts (1). Secure the Center Cross Support Bar (I) and Side Rails (E, F) to the Side Panels (D) using Connectors (C) and Bolts (T). Attach the Side Panels (D) to the Footboard Panel (B) using Connectors (C) and Bolts (T). Use Hardware 5 (M8x30mm screws) with Connectors (C) or Side Panels (D) for specific connections as shown.
Step 2
Attach Bed Legs (L) to the bottom of the Side Rails (E, G) and (F, H) using Bolts (3).
Step 3
Connect the assembled Side Rails (E, F, G, H) (with attached Legs (L)) to the Headboard (A) and Footboard (B). Use Connectors (C) and Bolts (1) for the headboard side connections, and Connectors (C) and Bolts (2) for the footboard side connections.
Step 4
Attach the Shorter Cross Support Bars (J1 or J2) to the Side Rails using Bolts (1) and Vertical Support Posts (K). Ensure the correct orientation of J1/J2 and K.
Step 5
Attach additional Vertical Support Posts (K) to the Side Rails. Then, attach Bed Legs (L) to the bottom of these Vertical Support Posts (K).
Step 6
Attach Angled Support Brackets (M) to the frame using Bolts (2). Attach more Vertical Support Posts (K) and Angled Support Brackets (M) using Bolts (3).
Step 7
Place the Bed Slats (N1, N2) onto the frame, aligning them with the support structure.
Step 8
Attach Corner Brackets (Q) to the inside corners of the frame. Attach Drawer Support Panels (S) to the frame using Corner Brackets (Q) and Screws (S). Also, attach Drawer Support Brackets (R) to the Drawer Support Panels (S).
Step 9
Attach Casters (O) to the Drawer Base/Support Panels (S). They should snap into place with an audible "CLICK!".
Step 10
Attach Drawer Slide Hardware (P) to the Side Rails of the bed frame and to the Drawer Base/Support Panels (S) using Screws (4).
Step 11
Connect the USB/Type-C Power Module (U) to the designated port on the Headboard (A). (Note: Power adapter/cable not included).
Step 12
Final check. Installation is complete.
