Introduction
Thank you for purchasing the ACEZUK M06 car battery jump starter kit. Please read the user manual carefully before using the product.
⚠️ Charge it first!
While you read the manual, you can start charging your M06 with your adapter (not included).
⚠️ Warning
This unit is for 12V battery vehicles. It can be dangerous if used with other types of batteries. Read and understand the safety information before using the jump starter, as it can cause electric shock, explosions, fires, material damage, and personal injury.
Technical Details
| Model | M06 |
|---|---|
| Type-C Input | 5V=3A 9V=2A |
| USB1 USB2 Output | 5V=3A |
| Air Compressor | 150PSI |
| Dimensions (L*W*H) | 166.3*126.2*53.2mm |
| Weight | 1.54lbs (0.7kg) |
| Jump Starter Output | 12V |
| Working Temperature | -20°C~60°C / -4°F~140°F |
| Internal Battery | Lithium Polymer |
| Screen Size | 72*52mm |
Know Your Product
[Diagram showing the device with numbered callouts]
1. EC5 Port
2. USB Output Port
3. Type-C Input Port
4. Air Inflation Hole
5. LED Light
6. LCD Screen
7. Mode Button
8. "-" Button
9. OK Button
10. Light Button
11. "+" Button
Technical Specifications
| No. | Button | Function |
|---|---|---|
| 1 | EC5 | Insert the jump cable firmly into the EC5 port. |
| 2 | USB Output | Charge your device via the USB port. |
| 3 | Type-C Input | 18W input. |
| 4 | Air Inflation Hole | For inflating your tires with the air hose. |
| 5 | LED Light | Normal, Slow Flash, SOS, Off. |
| 6 | LCD Screen | ① Display remaining capacity. ② Display inflation mode/unit/value/error warning. |
| 7 | Mode Button | To select the inflation mode for different items. |
| 8 | "-" Button | Decrease air pressure. |
| 9 | OK Button | Press the button to jump start your car. |
| 10 | Light Button | Press the button to turn on the flashlight. |
| 11 | "+" Button | Increase air pressure. |
Display Screen
[Diagram of the screen with numbered callouts]
| No. | Icon | Function |
|---|---|---|
| 1 | [Battery Level Icon] | To display battery capacity. |
| 2 | [Car Icon] [Motorcycle Icon] [Bicycle Icon] [Ball Icon] | Select different tire types for inflation. |
| 3 | PSI BAR KPA Kg/cm² | Air pressure unit. |
| 4 | [Temperature Icon] | Your battery temperature is abnormal. |
| 5 | [Fan Icon] | The fan is working. |
| 6 | OUT [Arrow Icon] | Charge other devices. |
| 7 | IN [Arrow Icon] | Recharge. |
| 8 | [Lightning Bolt Icon] | Fast charging. |
| 9 | [Digital Display] | Display values/error reminders. |
Recharge Your Starter
How to recharge the product
- Connect the USB-C end of the USB charging cable to the charger.
- Connect the USB-C end of the USB charging cable to the Type-C port of the product.
- The Type-C input port supports 5V/3A, 9V/2A. While recharging, the battery level indicator will flash continuously. When the battery level indicator is fully charged and stops flashing, it indicates it is fully charged. When recharging while off, only the battery level symbol is displayed.
NOTE: It is recommended to recharge the jump starter every 3-4 months to maintain efficiency and prolong the internal battery's lifespan even if the unit has not been used.
How to Judge When Fully Charged
| Indicator | Battery Level |
|---|---|
| 1 Bar [Bar Graph] | Less than 25% |
| 2 Bars [Bar Graph] | Between 25% and 50% |
| 3 Bars [Bar Graph] | Between 50% and 75% |
| 4 Bars [Bar Graph] | Between 75% and 100% |
Note: The battery indicators will illuminate circularly during charging; the illuminated indicators represent the current battery level. If all four battery indicators are lit, it means the charge is complete.
Charge Other Devices
In addition to jump-starting a car, this product can also supply power to a mobile phone, PSP, MP3/MP4, camera, and other consumer electronic devices.
[Description of images: A red car, a black storage case, a portable music player, a mobile phone, a digital camera, a pair of headphones.]
How to Start
Step 1 - Ready State
Insert the plug firmly into the jump starter's EC5 port. The screen will display the starter voltage, and the small icon at the top will cycle from left to right.
[Diagram showing device connected to jump starter cables, with indicators]
Indicators:
- ⚡ Low Voltage Indicator
- ? Reverse Connection Indicator
- -- Short Circuit Indicator
- ⚠️ Reverse Charge Indicator
- ❗ High Temperature Indicator
The starter voltage (when one end is connected to the car and the other to the starter). The car battery voltage (only when connected to the car).
Step 2 - Operation State
Connect the red clamp to the positive (+) terminal of the car battery and the black clamp to the negative (-). The screen will display the starter voltage, and the small icon at the top will no longer appear.
[Diagram showing red clamp on positive terminal, black clamp on negative terminal]
Step 3 - Turn on the Engine
- Start the engine within 90 seconds of entering the operation state; otherwise, the jump clamp will activate the standby protection.
- If the engine does not start correctly on the first attempt, try again. After 5 attempts, the smart clamp will activate protection; at this point, disconnect the clamp from the car battery and wait at least 20 seconds before reconnecting.
[Diagram showing jump starter connected to car battery and engine start button]
Step 4 - Remove the Clamp
Remove the clamp from the car battery and the jump starter within 30 seconds after the engine starts.
[Diagram showing removal of red and black clamps from battery terminals]
Note:
- Do not use this device as a car battery charger to charge car batteries.
- Ensure all electrical appliances on board the rescued vehicle are turned off before starting.
- Ensure the power is above 50% when using it to jump start your car.
- After a successful start, remove the product from the car battery within 30 seconds, otherwise, it may cause damage.
- Do not use the device to jump start the car continuously more than 5 times. It may cause the product to overheat and get damaged. Each start should be separated by two minutes.
- The product is only suitable for jump-starting vehicles. Do not use it on equipment like airplanes and boats.
- Due to long storage or shipping time, the battery's energy may become "virtual" and it must be fully charged before the first use. (Even if it shows sufficient energy, it may cause battery damage and fail to recharge).
Inflate Your Tires
1. OK Button:
- a.) When off, briefly press to turn on.
- b.) When on, not inflating, press the OK button to turn off.
- c.) When on, not inflating, press and hold the OK button for 3 seconds to start inflating.
- d.) When inflating, briefly press or hold for 3 seconds to stop inflating.
[Diagram showing device connected to air hose and tire valve]
2. M Button:
When the jump starter is on, press the M button to change the inflation mode. The mode sequence is: Car (default setting is 36 PSI) --- Motorcycle (default setting is 36 PSI) --- Bicycle (default setting is 60 PSI) --- Balls (default setting is 8 PSI). The corresponding symbol will be highlighted and change to its default setting value when you switch. Then, press and hold for 3 seconds to enter the unit switching mode. While the unit is flashing, briefly press to change the unit (PSI/BAR/KPA/Kg/Cm²). When the unit flashes six times without operation, it will stop.
[Diagram showing M, OK, *, + buttons]
3. "+" and "-" Buttons:
Adjust the preset air pressure value. Briefly press to increase or decrease, press and hold for 3 seconds to switch to rapid increase or decrease (the air pressure value returns to the default value after turning off or changing mode).
[Diagram showing M, OK, *, + buttons]
4. Inflation:
Connect the inflatable object after turning on the device. The connected object's pressure can only be displayed when the air pressure is above 3 PSI. If the real-time pressure is higher than the set value, it is useless to start the pump. If the real-time pressure is lower than the set value, press the OK button to start inflating. When the air pressure reaches the preset value during inflation, inflation will stop automatically.
5. Over-inflation Protection:
To prevent the tire from leaking during inflation. There are two specially designed situations for over-inflation protection. One is that the air pressure remains at "0" for 120 seconds during inflation and displays "a" flashing 6 times; The other is that the air pressure does not increase during inflation for 120 seconds, the machine will stop automatically and display "to" flashing 6 times.
6. Overheat Protection:
The product has battery overheat protection, and the temperature sensor is located on the exterior of the battery pack. When the battery temperature reaches 65°C+5°C, the battery board will stop supplying power (when the temperature drops to 55°C+5°C after protection, press the OK button to recover).
7. Suitability:
M06 is suitable for road bike tires (0-120 PSI), small car tires (0-40 PSI), and low-pressure inflation of boats or balls. It is not suitable for medium and large trucks or buses. (The tire pressure of heavy vehicles is relatively high, and the inflation time will be longer, which will cause the engine, air pump, and air pipe to withstand higher air pressure, resistance, and high temperature, affecting the product's lifespan or even damaging the air pump).
Tips
The maximum pressure for the custom mode is 150 PSI, while the values for the other four modes are fixed to avoid damage or safety risks.
| Mode | Pressure |
|---|---|
| Car | 58 PSI/4 Bar |
| Motorcycle | 51 PSI/3.5 Bar |
| Bicycle | 150 PSI/10.3 Bar |
| Basketball | 14 PSI/1 Bar |
Note: The air hose will get hot during inflation; Do not touch the air hose directly. Doing so could cause burns.
Ensure the Pressure Value is Correct
To avoid over-inflation, confirm the maximum inflation pressure of the objects being inflated. Over-inflating objects can cause damage and personal injury.
Tires
The recommended pressure for tires is generally indicated on the tire sidewall. Tire pressure recommendations/maximums can also be found inside the driver's door. Consult your vehicle's instructions/user manuals for information on load capacity and recommended tire pressure.
Balls
The recommended pressure can be found on the air valve of footballs, basketballs, volleyballs, and most other balls.
Air Pressure Reference Table
Bicycles
| Type | Recommended Pressure Range |
|---|---|
| Folding electric bicycle tires | 10-50 PSI/0.7-3.5 Bar |
| 12, 14, and 16-inch bicycle tires | 30-50 PSI/2.1-3.5 Bar |
| 20, 22, and 24-inch bicycle tires | 40-50 PSI/2.8-3.5 Bar |
| 26, 27.5, and 29-inch mountain bike tires | 45-65 PSI/3.1-4.5 Bar |
| Electric scooter tires | 40-50 PSI/2.8-3.5 Bar |
| 700c road bike clincher tires | 100-130 PSI/6.9-9.0 Bar |
| 700c road bike tubular tires | 120-145 PSI/83-10.0 Bar |
Motorcycles
| Type | Recommended Pressure Range |
|---|---|
| Scooters and street motorcycle tires | 26-43 PSI/1.8-30 Bar |
Cars
| Type | Recommended Pressure Range |
|---|---|
| Car tires | 32-41 PSI/2.2-2.8 Bar |
Balls
| Type | Recommended Pressure Range |
|---|---|
| Basketball | 7-9 PSI/0.5-0.6 Bar |
| Football | 8-16 PSI/0.6-11 Bar |
| Volleyball | 4-5 PSI/0.3 Bar |
| American Football | 12-14 PSI/0.8-1.0 Bar |
Note: The pressure values above are for reference only. Read the user manual or object instructions for pressure information.
Attention
- Be careful when inflating products like balloons, toys, floats, etc., which have an inflation range lower than the pump's. They cannot stop automatically at the preset pressure.
- a. If the inflated object has an inflation pressure below 38 PSI, the continuous inflation time cannot exceed 15 minutes. The machine must stop after 15 minutes of inflation and rest for 10 minutes before reuse.
- b. If the inflated object has an inflation pressure between 38 PSI and 60 PSI, the continuous inflation time cannot exceed 8 minutes. After 8 minutes of inflation, the machine must stop and rest for 10 minutes before reuse.
- c. If the inflated object has an inflation pressure between 60 PSI and 110 PSI, the continuous inflation time cannot exceed 4 minutes. After inflating for 4 minutes, the machine must stop and rest for 10 minutes before reuse.
- d. If the inflated object has an inflation pressure between 110 PSI and 150 PSI, the continuous inflation time must not exceed 2 minutes. After 2 minutes of inflation, the machine must stop and rest for 10 minutes before reuse; this can ensure the maximum lifespan of this product.
- The temperature of the inflated hose is relatively high after use; be careful. Hold the silicone sleeve with your hand and twist the hose to remove it. Do not touch the metal part of the hose head directly with your hand.
- To ensure safety, verify the required inflation pressure of the item being inflated before inflating it to avoid personal injury caused by explosions from over-inflation.
LED Light
[Diagram showing LED light location on the device]
LED Light: When turned on, briefly press the light button to turn on the flashlight; press briefly again to cycle through modes (dim, SOS); press briefly one more time to turn off the flash light. (When the lights are on, press and hold for 3 seconds to turn off the light).
CODE ERROR HANDLING
| CODE | ERROR | WHAT TO DO |
|---|---|---|
| E01 | Sensor Anomaly | Indicates a malfunction in the main control circuit of the equipment and requires professional technical maintenance. |
| E02 | Motor Overheating | Place the device in a shaded area or leave it for 5 minutes in an air-conditioned outlet and then use it again. |
| E04 | USB Overload or Short Circuit | Press the OK button to turn on the device after disconnecting the USB cable. If E04 does not reappear, you can reconnect the charged device. If E04 reappears, it indicates that the charged device is abnormal or does not match the discharge device. |
| E05 | Motor Overcurrent | Wait for the temperature to recover below 40°C before restarting inflation. If the phenomenon cannot be eliminated, professional expertise is required. |
| E06 | Abnormal Charge Voltage (>6.0V or <4.0V) | Charging can be stopped until the charger temperature returns to below 40°C before charging. If the phenomenon cannot be eliminated, change to a new charger. |
| E07 | Battery Temperature Too High for Recharging | Place the device in a shaded area or leave it to rest for 5 minutes in an air-conditioned outlet and then use it again. |
| E08 | Battery Temperature Too Low for Recharging | Place the device in an environment of 10°C -40°C for a period of time. |
| E09 | Battery Temperature Too High for Charging | Place the device in a shaded area or leave it to rest for 5 minutes in an air-conditioned outlet and then use it again. |
| E10 | Battery Temperature Too Low for Charging | Place the device in an environment of 10°C -40°C for a period of time. |
| E11 | USB-C Overload or Short Circuit | Press the OK button to turn on the device after disconnecting the USB-C cable. If E011 does not reappear, you can reconnect the charged device. If E011 reappears, it indicates that the charged device is abnormal or does not match the discharge device. |
| To | Leak | Check if the air hose connection has leaks or if the inflated products have leaks. |
Warnings
- Always read all instructions carefully before using your jump starter.
- Do not immerse your jump starter in water or expose it to rain or humidity.
- Never open or disassemble your jump starter, as this will void the warranty.
- Do not expose your jump starter to fire, intense heat, or flammable liquids.
- Charge the product only at temperatures between -20°C to +75°C.
- Keep away and out of reach of children.
- Do not insert foreign objects into ANY input or output.
- Do not allow the metal teeth of the red clamp to touch the metal teeth of the black clamp when connected to your jump starter.
- Do not connect the black clamp to the positive (+) terminal of the vehicle battery when connected to your jump starter.
- Do not connect the red clamp to the negative (-) terminal of the vehicle battery when connected to your jump starter.
- Do not open your jump starter to replace the internal battery. There are no user-replaceable parts inside your Jump Starter.
- Always disconnect the jump starter cables after use and store them separately.
- Check the product's power at least every three months and recharge it in time.
Battery Disposal
The battery is self-contained and cannot be replaced by the consumer. The battery must be disposed of properly when it no longer holds a charge. Proper charging practices increase the product's lifespan.
Warranty
For additional assistance or warranty coverage claims, contact us: Email: ACEZUK@outlook.com
