ACEZUK M02 Jump Starter User Manual
Introduction
Thank you for purchasing the ACEZUK M02 car jump starter kit. Please read the user manual carefully before using the product.
⚡Charge it first! While reading the manual, you can start charging your M02 with your adapter (not included).
⚠️Warning: This device is intended for vehicles equipped with 12V batteries. It can be dangerous if used with other types of batteries. Read and understand the safety information before using the jump starter, as improper use can lead to electric shock, explosions, fire, property damage, and personal injury.
Know Your Product
The ACEZUK M02 Jump Starter has the following components:
- 1. Jump Start Port: For connecting the smart clamps.
- 2. LED Light: Provides illumination.
- 3. USB 3.0 Output: For fast charging of compatible devices.
- 4. USB 5V/2.4A Output: For charging standard USB devices.
- 5. TYPE-C Input: For recharging the jump starter.
- 6. Power Switch: To turn the device on/off.
- 7. LCD Indicator: Displays the remaining battery capacity.
Diagram Description: A top-down view of the ACEZUK M02 jump starter showing the ports and the LCD screen. The ports are labeled: USB-OUT, USB-OUT, and USB-C IN. The power switch and LED light are also visible.
Technical Specifications
| NO. | Function | Operation |
|---|---|---|
| 1 | Jump Start Port | Insert the jump starter cable plug completely into the jump start port. |
| 2 | LED Light | Normal, SOS, Strobe, Warning, Off. |
| 3 | USB 3.0 Output | Charge your USB devices 75% faster than standard charging. |
| 4 | USB 5V/2.4A Output | Charge your USB devices up to 5V/2.4A. |
| 5 | TYPE-C Input | Recharge the device using the included Type-C cable. |
| 6 | Power Switch | Press the button to turn the device on/off. Press and hold the button to turn the flashlight on/off. |
| 7 | LCD Indicator | Displays remaining capacity: 25%, 50%, 75%, and 100%. |
Smart Clamp Indicator
Diagram Description: An illustration of the smart clamps connected to a battery terminal, with a digital display showing voltage and various indicator icons.
- ⚡Low Voltage Indicator: Indicates low battery voltage.
- ?Reverse Connection Indicator: Signals an incorrect connection of the clamps.
- ➕➖Short Circuit Indicator: Alerts to a short circuit.
- ⚡Reverse Charge Indicator: Indicates reverse charging.
- ?️High Temperature Indicator: Shows when the device is overheating.
- Voltage Display: Shows the voltage of the jump starter or the car battery.
Detailed Specifications
| Model | M02 |
|---|---|
| USB C Input | 5V/2A, 9V/2A, 12V/1.5A |
| Output 1 | 5V/3A, 9V/2A, 12V/1.5A |
| Output 2 | 5V/2.4A |
| Dimensions (L*W*H) | 181.5*92.6*39mm |
| Weight | 1.87lbs (0.87kg) |
| Operating Temperature | -20°C to 60°C (-4°F to 140°F) |
| Reverse Flow Protection | ≥12.6V ± 0.3V |
| Charging Temperature | 5°C to 45°C (41°F to 140°F) |
| LED Flashlight | 400 lumens |
| Internal Battery | Lithium Polymer |
| Screen Size | 47*20mm |
Recharge Your M02
Charging the Booster Battery
- At Home:
1. Connect the USB cable to any USB charger (5V/2A suggested).
2. Connect the Type-C port to the jump starter. - In the Car:
1. Plug the car adapter (not included) into the socket.
2. Connect the Type-C port to the Booster Battery.
?NOTE: It is recommended to recharge the Jump Starter every 3-4 months to maintain efficiency and prolong the internal battery's lifespan, even if the device has not been used.
Charging Other Devices
In addition to jump-starting a car, this product can also power a mobile phone, PSP, MP3/MP4, camera, and other consumer electronic devices.
Diagram Description: Icons representing a car, a portable game console, a music player, and a camera, illustrating the versatility of the jump starter for charging various devices.
Starting Your Vehicle
Step 1 - Ready State
Insert the plug completely into the jump starter's EC5 port. The clamp indicator will display the jump starter's voltage, and the small icon at the top will cycle from left to right.
Diagram Description: Close-up of the EC5 port on the jump starter with the smart clamp cable being inserted.
Step 2 - Working State
Connect the red clamp to the positive (+) terminal of the car battery and the black clamp to the negative (-). The clamp indicator will show the jump starter's voltage, and the small icon at the top will no longer be displayed.
Diagram Description: Illustration showing the red and black smart clamps connected to the positive and negative terminals of a car battery.
Step 3 - Start the Engine
- Please start the engine within 90 seconds after entering the working state. Otherwise, the jump starter clamp will activate protection against delay.
- If the engine does not start successfully on the first try, please restart it. After 5 attempts, the smart clamp will trigger protection. At this point, disconnect the clamp from the car battery and wait at least 20 seconds before reconnecting.
Step 4 - Remove the Clamp
Remove the smart clamp from the car battery and the jump starter within 30 seconds after the engine starts.
Diagram Description: Illustration showing the smart clamps being disconnected from the car battery after the engine has started.
REMARK:
- Do not use this device as a car battery charger to charge car batteries.
- Ensure all onboard electrical devices in the assisted vehicle are turned off before starting.
- Ensure the power is above 50% when using it to start your car.
- Make sure the copper teeth on each side of the clamp are in good contact with the battery terminal for easier starting.
- After a successful start, remove the product from the car battery within 30 seconds to avoid damage.
- Do not use the device to start the car continuously more than 3 times. This could cause the product to overheat and be damaged. Each start should be spaced by two minutes.
- The product is suitable only for starting 12V gasoline and diesel vehicles. Do not use it on equipment such as airplanes and ships.
- Due to long storage or shipping, the battery power may become virtually depleted and must be fully charged before the first use. (Even if it shows sufficient power, it may cause damage to the battery and charging failure.)
Indicators and Troubleshooting
| NO. | Type | State | Suggestion |
|---|---|---|---|
| 1 | Low Voltage Protection | Trigger Condition: Jump starter voltage is below 14.0V. Indicators: Low voltage indicator lights up, buzzer sounds every second, and the current jump starter voltage is displayed simultaneously. |
The jump starter battery is too low to start; please charge it first. |
| 2 | Ready State | The current jump starter voltage is displayed, and the small icon at the top cycles from left to right simultaneously. | Please proceed to Step 2. |
| 3 | Working State | The current jump starter voltage is displayed, and the small icon at the top is no longer shown. | Please proceed to Step 3. |
| 4 | Battery Voltage Detection | Trigger Condition: The smart clamp is connected only to the car battery (car battery voltage must be above 8V). Indicators: ⚡ lights up, the current car battery voltage is displayed simultaneously. |
N/A |
| 5 | Reverse Charge Protection | Trigger Condition: Jump starter voltage increases after starting. Indicators: Reverse charge indicator ⚡ lights up, ••• flashes, buzzer sounds every second. |
Disconnect the clamp from the car battery. |
| 6 | Reverse Connection Protection | Trigger Condition: Red and black clamps are connected to the wrong positive and negative terminals of the car battery. Indicators: Reverse connection indicator ? lights up, ••• flashes, buzzer sounds every second. |
Remove the clamp from the car battery and reconnect it correctly. |
| 7 | Short Circuit Protection | Trigger Condition: Red and black clamp terminals are short-circuited in the ready state. Indicators: Short circuit indicator ⚡ lights up, ••• flashes, buzzer sounds every second. |
1. Remove the negative terminal from the car battery, fix it directly to the jump starter clamp, then try to start. 2. If the engine still cannot start, check the car's internal circuit or replace the smart clamp. |
| 8 | High Temperature Protection | Trigger Condition: 80±10°C Indicators: High temperature indicator ?️ lights up, ••• flashes, buzzer sounds every second. |
Stop operation and wait for the temperature to drop to 65 ± 10°C. |
| 9 | Timeout Expiration Protection | Trigger Condition: No operation for more than 90 seconds after a correct connection; the smart clamp automatically stops output. Indicators: ••• flashes. |
Remove the clamp from the car battery and the jump starter, then reconnect it. |
| 10 | Continuous Jump Start Protection | Trigger Condition: 5 continuous jump starts. Indicators: ••• flashes. |
Remove the clamp from the car battery and the jump starter, then reconnect it after at least 20 seconds. |
LED Light
Lighting Button: Press once to turn on the light (it can also turn on the light when off). Press a second time to enter slow flashing mode. Press a third time to enter SOS mode. Press a fourth time to turn off the light. Alternatively, press and hold the lighting button for 3 seconds to turn the red and blue flashing warning light on or off.
Warnings
- Read all instructions carefully before using the starter.
- Do not immerse your starter in water, expose it to rain or humidity.
- Do not open or disassemble your jump starter, as this will void your warranty.
- Do not expose your jump starter to fire, intense heat, or flammable liquids.
- Only charge the product at temperatures between -20℃ to +75°C.
- Store out of reach of children.
- Do not insert foreign objects into the device.
- Do not let the metal parts of the red and black clamps touch each other when connected to the device.
- Do not connect the black clamp to the positive (+) terminal of the battery when it is connected to the starter. Do not connect the red clamp to the negative terminal of the battery when it is connected to the starter.
- Do not open your jump starter to replace the internal battery. The device contains no user-replaceable parts.
- Always disconnect the jump starter cables from the device after use and store them separately.
- Check the battery power at least every 3 months and charge the product in time.
Battery Disposal
The battery is fully integrated into the device and cannot be replaced by the user. When the battery no longer holds a charge, it must be disposed of according to current regulations. Proper charging conditions extend the device's lifespan.
Warranty
ACEZUK offers users a 24-month warranty from the date of purchase.
Contact Us
For additional assistance or to exercise your warranty, please contact ACEZUK:
E-Mail: ACEZUK@outlook.com
