RÅGRUND Shelving Unit

by IKEA

Important Safety Information

⚠️ WARNING: RISK OF FURNITURE TIP-OVER

Furniture tip-over can cause severe injury or death. To reduce this risk, it is crucial to follow these safety guidelines:

ALWAYS install the provided anti-tip device to secure the furniture to the wall. [Diagram: Warning triangle with exclamation mark]
NEVER place a television or other heavy objects on this product. [Diagram: Television icon with a cross through it]
NEVER allow children to stand, climb, or hang on any drawers, doors, or shelves. [Diagram: Child climbing on furniture with a cross through it]
NEVER open more than one drawer at a time. [Diagram: Open drawers with a cross through multiple open drawers]
Place the heaviest items in the lowest drawers to improve stability. [Tip: Load management]

Assembly Instructions

Tools and Parts Required

Before you begin, gather the necessary tools and check that all parts are present.

Tools:

[Screwdriver]
[Pencil]
[Tape Measure]

Included Parts:

1x Allen Key (Part #100006)
30x Screws (Part #130608)
1x Anti-tip Strap Kit (Part #128481)

[Diagram: Illustration of the tools and parts listed above.]

Assembly Steps

Step 1: Prepare Side Panels

Take the two main side panels. Insert the wooden dowels into the pre-drilled holes on one of the side panels. Ensure they are fully seated. [Diagram: Close-up showing dowels being inserted into holes on the edge of a panel.]

Step 2: Attach First Side Panel to Base

Align the base panel with the dowels on the first side panel. Secure the base panel to the side panel using screws (Part #130608) and the Allen key (Part #100006). [Diagram: Shows a side panel standing upright, with the base panel being attached to its bottom edge using screws.]

Step 3: Insert and Secure Shelves

Insert the shelves into the designated slots or grooves on the attached side panel. Secure each shelf from the outside using screws (Part #130608). [Diagram: Shows shelves being slid into place and then secured with screws from the exterior.]

Step 4: Attach Second Side Panel

Align the second side panel with the open ends of the shelves and the base panel. Secure the second side panel to the base panel and each shelf using screws (Part #130608). [Diagram: Shows the second side panel being attached to the assembly, connecting to the base and shelves.]

Step 5: Add Remaining Shelves

Continue inserting and securing the remaining shelves into the unit using screws (Part #130608) for each shelf. [Diagram: Shows more shelves being added to the structure.]

Step 6: Assemble Full Unit

If the unit is designed to be assembled in sections, connect them now using the provided screws (Part #130608). The diagram shows two main sections being joined together. [Diagram: Illustrates joining two larger assembled parts of the shelving unit.]

Step 7: Position the Unit

Carefully move the fully assembled shelving unit to its final desired location.

Step 8: Prepare for Wall Mounting

Measure 30mm (approximately 1 3/8 inches) down from the top edge of the unit on the back. Mark this point. This is where the anti-tip strap will attach to the unit. [Diagram: A tape measure is shown indicating a 30mm measurement from the top edge of the unit.]

Step 9: Secure Unit to Wall

Attach one end of the anti-tip strap (Part #128481) to the marked point on the back of the unit using a screw. Identify a suitable wall stud or use appropriate wall anchors (not included). Attach the other end of the strap securely to the wall. Ensure the strap is taut to prevent tipping. [Diagram: Shows the strap being attached to the unit and then to a wall, with a close-up of the connection.]

Step 10: Final Check

Double-check that all screws are tightened and the unit is stable and securely fastened to the wall. [Diagram: Shows the completed, wall-mounted unit.]

[Diagram: Person looking confused at parts, then on the phone with IKEA.]

[Diagram: Final assembled unit shown in a corner against a wall.]

For further assistance, please contact IKEA.

	RÅGRUND Shelving Unit - Assembly Instructions and Safety Warnings Comprehensive assembly guide and critical safety information for the IKEA RÅGRUND shelving unit. Includes instructions on installing the anti-tip device to prevent furniture tipover accidents.
	RÅGRUND Shelving Unit Assembly Instructions Comprehensive assembly guide for the IKEA RÅGRUND shelving unit. This document provides step-by-step instructions, a parts list, and essential safety warnings to ensure proper and secure installation of your bamboo shelving unit.
	RÅGRUND Shelving Unit Assembly Instructions \| IKEA Step-by-step guide to assembling the IKEA RÅGRUND shelving unit. Includes detailed steps, parts list, and crucial safety warnings to prevent furniture tip-over. Learn how to safely assemble and secure your RÅGRUND unit.
	IKEA RÅGRUND Assembly Instructions Step-by-step assembly guide for the IKEA RÅGRUND shelving unit, including safety warnings and part lists.
	RÅGRUND Shelving Unit Assembly Instructions Detailed assembly guide for the IKEA RÅGRUND shelving unit, including essential safety information regarding furniture tip-over prevention and proper installation.
	RÅGRUND Shelving Unit Assembly Instructions and Safety Guide Comprehensive assembly instructions and critical safety warnings for the IKEA RÅGRUND shelving unit, emphasizing the importance of wall attachment to prevent tip-over injuries.
	IKEA RÅGRUND Corner Shelf Assembly Instructions and Safety Guide Official assembly instructions and essential safety warnings for the IKEA RÅGRUND corner shelf. Learn how to safely assemble and install your RÅGRUND unit, including critical tip-over prevention measures.
	RÅGRUND Shelving Unit Assembly Instructions Concise assembly guide and safety warnings for the IKEA RÅGRUND shelving unit. Learn how to safely build and secure your furniture to prevent tip-over accidents.