YITAHOME TZBTCS-V1 12x18 FT Hardtop Gazebo Assembly Instructions
Model Numbers: FTPLCG-0239, FTPLCG-0240, FTPLCG-0241, FTPLCG-0242, FTPLCG-0243
Important Warnings
WARNING
- Must use ground nails, ropes, and expansion screws for stability to avoid devastating injuries to people inside or nearby and property damage caused by a collapsing gazebo.
- Do not use this gazebo in high winds, heavy snow, or inclement weather. It is not designed to withstand strong gusts of wind, heavy snow accumulation, or other inclement weather. Take precautions when wind speed exceeds 25 MPH, and clear snow when it accumulates more than 2 inches.
- Before use, thoroughly inspect the gazebo to make sure all bolts, nuts, and buckles have been completely tightened and securely fastened.
- Warranty does not cover damages, losses, or injuries resulting from improper installation, misuse, not using stability accessories mentioned above, non-snow cleaning, or failure to take precautionary measures.
General Assembly Instructions
- Two or more people are required for assembly.
- A ladder and electric drill may be necessary.
- Do not erect the structure in heavy winds or inclement weather.
- Do not leave this unit up for extended periods of time, as it is not a permanent structure designed to withstand sustained wind or rain. It is a temporary, portable shelter that shields you from sunlight and rain. The screens also block flying insects.
- Do not use candles, matches, or any open flames near the tent.
- To better align screws for practical situations, do not fully tighten screws initially.
- Professional installation is highly recommended.
Parts List
| Item No. | Reference Image Description | Qty. |
|---|---|---|
| A | Long vertical pole | X4 |
| A1 | Shorter vertical support pole | X2 |
| B | Long horizontal beam | X2 |
| B1 | Long horizontal beam | X2 |
| C | Long horizontal beam | X2 |
| C1 | Long horizontal beam | X2 |
| E2 | Short horizontal beam | X2 |
| E | Roof support beam | X4 |
| Ea | Roof support beam | X4 |
| E1 | Roof support beam | X8 |
| F | Roof support beam | X4 |
| F1 | Roof support beam | X2 |
| F2 | Roof support beam | X2 |
| F3 | Roof support beam | X2 |
| F4 | Roof support beam | X2 |
| G1 | Roof panel | X2 |
| G2 | Roof panel | X2 |
| G3 | Roof panel | X2 |
| G4 | Roof panel | X2 |
| D | Roof panel | X2 |
| D1 | Roof panel | X2 |
| D2 | Roof panel | X2 |
| D3 | Roof panel | X2 |
| G5 | Roof panel | X2 |
| D4 | Roof panel | X2 |
| D5 | Roof panel | X2 |
| H | Corner bracket | X4 |
| H1 | Corner bracket | X4 |
| H2 | Corner bracket | X4 |
| J | Base plate/foot | X6 |
| U1 | Connector bracket | X2 |
| U2 | Connector bracket | X2 |
| K | Vertical support connector | X4 |
| K1 | Connector piece | X6 |
| L | Roof support beam | X1 |
| M | Roof support beam | X1 |
| N | Roof support beam | X12 |
| N1 | Connector piece | X8 |
| P | Connector piece | X6 |
| Pa | Connector piece | X4 |
| P1 | Roof support beam | X3 |
| Q1 | Roof panel | X2 |
| Q2 | Roof panel | X2 |
| Q3 | Roof panel | X2 |
| Q4 | Roof panel | X2 |
| S2 | Roof panel | X2 |
| S3 | Roof panel | X4 |
| T | Curtain | X4+X2 |
| T1 | Curtain | X4+X2+X1 |
| U | Hook | X152 |
| V | Wrench | X6 |
| Y | Fastener/Screw | X144 |
| Z | Fastener | X72 |
| Z1 | Fastener | X12 |
| 1 | Screw M6X15mm | X234 |
| 2 | Screw M6X23mm | X16+X88 |
| 3 | Screw M5X12mm | X38 |
| 4 | Screw ST4.8X12mm | X28 |
| 5 | Fastener | X3 |
| 6 | Screw M6X42mm | X40 |
| 9 | Screw M6X50mm | X6 |
| 10 | Fastener | X18 |
| 11 | Wrench | X1 |
Assembly Steps
Step 1
Attach a long vertical pole (A) to a flat base plate (J) using three M6x15mm screws (1). The diagram shows the pole connecting to the base plate, with screws inserted through designated holes.
Step 2
Connect long horizontal beams (B, B1) to connector pieces (P) using screws (1). Ensure the three holes on part P face upwards. The diagram shows two B and two B1 beams connecting to two P connectors.
Step 3
Connect long horizontal beams (C, C1) and short horizontal beams (E2) to connector pieces (P) using screws (1). The diagram shows two C, two C1, and two E2 beams connecting to four P connectors.
Step 4
Assemble the main frame by connecting the four long vertical poles (A) to the top horizontal beams (B, B1, C, C1, E2) using screws (1). The diagram shows the four corner poles connected to the top horizontal beams.
Step 5
Attach corner brackets (H1, H2) to the top corners of the frame where poles and beams meet, using screws (3). The diagram shows these brackets being secured.
Step 6
Attach corner brackets (H) to the frame structure using screws (1). The diagram illustrates their placement on the upper frame.
Step 7
Attach vertical support connectors (K) to the vertical poles using screws (4). The diagram shows these connectors being fastened to the poles.
Step 8
Slide hooks (U) onto the channels of the horizontal beam rails (C, C1, E2, B, B1). Ensure hooks face inward. The diagram shows hooks being inserted into the beam channels.
Step 9
Attach connector pieces (K1) using screws (4) and fasteners (3). The diagram shows K1 being attached to the frame, possibly with the aid of a wrench (V).
Step 10
Assemble secondary pole units consisting of part A1, connector brackets (U1, U2), and base plate (J) using screws (1).
Step 11
Attach the assembled secondary pole units (A1) to the main gazebo frame using screws (1). The diagram shows these units being secured to the structure.
Step 12
Attach roof support beams (E, Ea, L, Pa) to the frame structure using screws (1). The diagram illustrates these beams being connected.
Step 13
Attach roof support beams (E) to the frame using screws (1). The diagram shows their placement on the upper structure.
Step 14
Attach roof support beams (E, E1) to the roof structure using screws (1). The diagram shows these beams being secured.
Step 15
Attach roof support beam (M) to roof support beam (L) using screws (1). The diagram shows this connection.
Step 16
Attach roof panels (D4, D5, G5, N) to the roof structure using screws (1). The diagram shows these panels being fastened into place.
Step 17
Attach roof support beams (P1) to the frame using screws (9) and fasteners (5). The diagram shows these supports being installed.
Step 18
Attach roof panels (Q1, Q2, Q3, Q4, S, Sa) to the frame using fasteners (Z or Z1). The diagram indicates these panels are attached, and notes that fastener Z can be tapped into place with a screwdriver.
Step 19
Attach roof panels (G, R1, R2, R3, R4, S1, S2, S3) to the frame using fasteners (Z or Z1). The diagram shows these panels being secured, and notes that fastener Z can be tapped into place with a screwdriver.
Step 20
Attach various roof panels (S, S1, S2, S3, Sa) to the top frame structure. The diagram shows their placement.
Step 21
Attach roof panels (D1, D2, D3, N, N1) to the roof structure using screws (1). The diagram illustrates their installation.
Step 22
Attach roof panels (F, F1, F2, F3, F4) to the roof structure using screws (1). The diagram shows these panels being fastened.
Step 23
Attach roof panels (G, Q1, Q2, Q3, Q4, R1, R2, R3, R4) to the roof structure. The diagram shows these panels being installed.
Step 24
Attach roof panels (Q1, Q2, Q3, Q4) to the horizontal beams (B, B1) using fasteners (Y) and roof support (E1). The diagram shows this connection.
Step 25
Attach roof panels (G, R1, R2, R3, R4) to the horizontal beams (C, C1, E2) using fasteners (Y) and roof support (E1). The diagram illustrates this connection.
Step 26
Install the ceiling using parts (Y) and fasteners (2, 6). Notes: Fix screws on the central beam first to prevent the iron sheet from falling. Do not fully secure screws until all are in position. Two persons are needed for installing Part Y; one secures position from inside, the other inserts screws from outside.
Step 27
Attach roof panels (G1, G2, G3, G4, D, N, N1) to the roof structure. The diagram shows their placement.
Step 28
Attach curtains (T) to the gazebo frame. The diagram indicates specific attachment points based on the number of holes on the curtain parts and the corresponding frame parts (B, B1, C, C1, E2).
Step 29
Attach curtains (T) using hooks (U). The diagram shows hooks being attached to the curtains and then to the frame, paying attention to the sidewall curtain's installation position.
Step 30
Attach netting (T1) to the gazebo frame. The diagram shows netting with specific hole counts attaching to frame parts (B, B1, C, C1, E2).
Step 31
Attach curtains (T1) using hooks (U). Notes explain how to connect curtains (T1 and T) together and secure them to the frame. Hooks are attached to netting on parts A and A1.
Step 32
Secure the gazebo to the ground using expansion screws (10) for cement surfaces or ground nails (11) for grassy surfaces. The diagram shows correct and incorrect installations. Warnings about wind resistance and the importance of secure anchoring are reiterated.
Step 33
Installation Completed. The diagram shows the fully assembled gazebo.
Contact Information
YITAHOME
Pure & Easy
Contact Us:
For installation questions, contact YITAHOME at +1 (888) 717-8084 (Mon-Fri 8:00 AM-4:30 PM PST / Sat. 8:00 AM-12:00 PM PST) or email after-sale.cs@hotmail.com.
Alternative contact for Amazon.com orders:
- Log into your Amazon account.
- Go to “Your Orders” and find the purchase.
- Click on “Contact Seller”.
