⚠️ WARNING
1. Must use ground nails, ropes, and expansion screws for whichever ground you install on for stability to avoid devastating injuries for people inside or nearby and property damage caused by a collapsing gazebo.
2. Do not use this gazebo in high winds, heavy snow, or inclement weather. It is not designed to withstand strong gusts of wind, heavy snow accumulation, or other inclement weather. Must take precautions when the wind speed exceeds 25 MPH, and clear snow when it accumulates more than 2 inches.
3. Before use, thoroughly inspect the gazebo to make sure all bolts, nuts, and buckles have been completely tightened and securely fastened.
4. Warranty does not cover damages, losses, or injuries resulting from improper installation, misuse, not using stability accessories mentioned above, non snow cleaning, failure to take precautionary measures, etc.
Assembly Notes & Requirements
1. Two or more people are required for assembly.
2. A ladder and electric drill may be necessary.
3. Do not erect the structure in heavy winds or inclement weather.
4. Do not leave up this unit for extended periods of time, as it is not a permanent structure or designed to withstand sustained wind or rain. It is a temporary, portable shelter that shields you from sunlight and rain. The screens also block flying insects.
5. Do not use candles, matches, or any open flames near the tent.
6. To better align the screws for practical situations, do not fully tighten screws initially.
7. Professional installation is highly recommended.
Parts List
| Item No. | Reference Image Description | Qty. |
|---|---|---|
| A | Leg Post | X4 |
| B | Horizontal Beam | X2 |
| B1 | Horizontal Beam | X2 |
| C | Horizontal Beam | X2 |
| C1 | Horizontal Beam | X2 |
| D | Roof Beam | X4 |
| E | Roof Cross Support | X6 |
| F | Roof Panel Connector | X2 |
| F1 | Roof Panel Connector | X4 |
| F2 | Roof Panel Connector | X4 |
| G | Roof Support | X2 |
| G1 | Roof Support | X4 |
| G2 | Roof Support | X4 |
| G3 | Roof Support | X2 |
| G4 | Roof Support | X2 |
| G5 | Roof Support | X2 |
| G6 | Roof Support | X2 |
| H | Corner Support Bracket | X4 |
| H1 | Corner Support Bracket | X4 |
| K | Roof Corner Bracket | X4 |
| K1 | Roof Corner Bracket | X2 |
| K2 | Roof Corner Bracket | X2 |
| L | Roof Support Component | X1 |
| M | Central Roof Component | X1 |
| N | Roof Support Connector | X12 |
| N1 | Roof Support Connector | X6 |
| P | Beam Connector Plate | X4 |
| Q | Roof Panel | X2 |
| Q1 | Roof Panel | X4 |
| Q2 | Roof Panel | X4 |
| Q3 | Roof Panel | X4 |
| Q4 | Roof Panel | X4 |
| R1 | Roof Panel Edge Trim | X4 |
| R2 | Roof Panel Edge Trim | X4 |
| R3 | Roof Panel Edge Trim | X2 |
| S | Netting Panel | X4 |
| T | Curtain Panel | X4 |
| U | Curtain Hook/Clip | X128 |
| W3 | Curtain Hook/Clip | X6 |
| 1 | M6x16mm Screw | X136 |
| 2 | M6x15mm Screw | X16 |
| 3 | M5x12mm Screw | X16 |
| 4 | ST4.8x12mm Screw | X16 |
| 5 | Bolt | X2 |
| 6 | Bolt | X1 |
| 7 | Bolt | X1 |
| 8 | Expansion Screw | X12 |
| 9 | Ground Nail | X1 |
| 10 | Ground Nail | X12 |
Assembly Steps
Step 1
Assemble the base of a leg post. Attach part A (leg post) to part J (base plate) using screws (1).
Parts used: A (4 pcs), J (4 pcs), 1 (12 pcs)
Step 2
Connect horizontal beams. Attach parts B and B1 to part P (connector plate). Attach parts C and C1 to part P. Ensure the holes on part P face upwards. Use screws (1) and possibly U (clips) for securing.
Parts used: B (2 pcs), B1 (2 pcs), C (2 pcs), C1 (2 pcs), P (4 pcs), 1 (32 pcs), U (128 pcs)
Step 3
Connect the leg posts (A) to the assembled horizontal beams (B, B1, C, C1) using screws (1) and (2).
Parts used: A (4 pcs), B, B1, C, C1 assemblies, 1 (16 pcs), 2 (16 pcs)
Step 4
Attach corner support brackets (H, H1) to the top corners of the leg posts (A) using screws (1).
Parts used: H (4 pcs), H1 (4 pcs), 1 (16 pcs)
Step 5
Attach roof corner brackets (K, K1, K2) to the top structure using screws (3) and (4).
Parts used: K (4 pcs), K1 (2 pcs), K2 (2 pcs), 3 (4 pcs), 4 (16 pcs)
Step 6
Assemble a specific roof support component (L) using part 6.
Parts used: L (1 pc), 6 (1 pc)
Step 7
Attach roof beams (D) to the structure using screws (1).
Parts used: D (4 pcs), 1 (8 pcs)
Step 8
Attach more roof beams (D) to the structure using screws (1).
Parts used: D (4 pcs), 1 (4 pcs)
Step 9
Attach roof cross supports (E) using screws (3) and clips/hooks (W3).
Parts used: E (6 pcs), W3 (6 pcs), 3 (12 pcs)
Step 10
Attach more roof cross supports (E) and roof beams (D) to the structure. Secure with screws (1). Also involves part L.
Parts used: D (multiple), E (multiple), L (multiple), 1 (18 pcs)
Step 11
Attach the central roof component (M) using bolts (5) and (7).
Parts used: M (1 pc), 5 (2 pcs), 7 (1 pc)
Step 12
Attach roof supports (G5, G6) and connectors (N) to the roof structure using screws (1).
Parts used: G5 (2 pcs), G6 (2 pcs), N (4 pcs), 1 (10 pcs)
Step 13
Install roof panels (R1, R2, R3). Note: Remove protective films from both sides of these parts before installation.
Parts used: R1 (4 pcs), R2 (4 pcs), R3 (2 pcs)
Step 14
Attach roof supports (G3, G4) and connectors (N) to the roof structure using screws (1).
Parts used: G3 (2 pcs), G4 (2 pcs), N (4 pcs), 1 (10 pcs)
Step 15
Install roof panels (F, F1, F2, Q, Q1, Q2). Note: Remove protective films from both sides of these parts before installation.
Parts used: F (2 pcs), F1 (4 pcs), F2 (4 pcs), Q (2 pcs), Q1 (4 pcs), Q2 (4 pcs)
Step 16
Install roof panels (Q, Q3, Q4). Note: Remove protective films from both sides of these parts before installation.
Parts used: Q (2 pcs), Q3 (4 pcs), Q4 (4 pcs)
Step 17
Attach final roof supports (G, G1, G2) and connectors (N, N1) to the roof structure using screws (1).
Parts used: G (2 pcs), G1 (4 pcs), G2 (4 pcs), N (4 pcs), N1 (6 pcs), 1 (10 pcs)
Step 18
Attach curtain panels (T). One part of the curtain has 7 holes for hanging on Part B or B1. The other part has 9 holes for hanging on Part C or C1.
Parts used: T (4 pcs)
Step 19
Attach curtain panels (T). Pay attention to the sidewall curtain's installation position. Use clips/hooks (U) to attach.
Parts used: T (4 pcs), U (multiple)
Step 20
Attach netting panels (S). One part of the netting has 7 holes for hanging on Part B or B1. The other part has 9 holes for hanging on Part C or C1.
Parts used: S (4 pcs)
Step 21
Secure netting (S) and curtains (T) together using hardware (1, 2, 3). Attach hardware (1, 3) to secure netting and curtains. Hang hooks attached to netting on Part A.
Parts used: S, T, 1, 2, 3
Step 22
Installation Completed. To improve wind resistance, ensure stability. Use expansion screws (8) for cement surfaces and ground nails (10) for grassy surfaces. If not installed, strong winds may topple the gazebo.
Parts used: 8 (12 pcs), 10 (12 pcs)
Contact Us
If you have any questions about the installation of YITAHOME products, please contact YITAHOME customer service at +1 (888) 717-8084 from Mon-Fri 8:00 AM-4:30 PM PST / Sat. 8:00 AM-12:00 PM PST or e-mail us at after-sale.cs@hotmail.com.
Alternative method to contact YITAHOME (amazon.com orders only):
- Log into your Amazon account.
- Go to “Your Orders” and find the purchase.
- Click on “Contact Seller”.
