Laresar L6 Pro Robot Vacuum Cleaner User Manual
Brand: Laresar
1. Important Safety Information
ATTENTION: Before using this device, please read all instructions in the manual and the warning labels on the device carefully.
This user manual contains information about the official models: Laresar L6 Pro Robot Vacuum Cleaner and Laresar LS-01 Dust Collection Charging Station.
Application Area
- This device is intended for indoor use only. Do not use outdoors or on wet surfaces.
- To prevent access to balconies and ensure safe operation, a physical barrier should be used.
- Do not use this device on untreated, unsealed, waxed, or rough floors, as this may cause damage to the floor and the device.
- Use only on hard floors or low-pile carpets.
- This device is designed to be used on floors without scratching them. However, it is recommended to test the device in a small area of the room to be cleaned before cleaning the entire room to ensure no scratches occur.
- Do not use this device to vacuum bleach, paint, chemicals, or wet items.
- Do not use this device to vacuum burning or smoking items.
- Do not pour liquids into the device or immerse it in water.
About Using the Device
- This device can be used by children aged 8 years and above, and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge, if they have been supervised or instructed in the safe use of this device and understand the associated hazards.
- Children should be supervised to ensure they do not play with this device. Cleaning and maintenance should not be performed by children without adult supervision.
- This device is not a toy. Do not sit or stand on this device. Young children and pets should be supervised when this device is in operation.
- Before using this device, pick up items such as clothing and loose paper. Lift the cords for blinds or curtains and remove power cords and fragile items. If this device drives over and pulls on a power cord, an item could be pulled off a table or shelf.
About Using the Charging Station
- Children and pets should be supervised during the operation of the charging station.
- Do not sit or stand on this charging station.
- Do not use without the dust bag and/or filter installed.
- Do not insert objects into the openings. Do not use if an opening is blocked; keep it free from dust, lint, hair, and anything that could impede airflow. Do not place foreign objects inside and ensure no foreign objects are present.
- Risk of electric shock; use this charging station only in a dry location.
- Do not touch the plug or the device with wet hands.
2. Charging Notes
- This device must only be operated with the supplied power adapter (LS-03).
- The battery must be removed from this device before this device is disposed of.
- This product comes with a power cord approved for the region and is intended for connection to a standard household power outlet only.
- The product must not be used with any power converters. The use of power converters will immediately void the warranty.
- If you live in an area prone to thunderstorms, it is recommended to use additional surge protection.
- The external flexible cable or cable of the power adapter cannot be replaced; if the cable is damaged, the power adapter must be discarded.
- If not used for a long time, fully charge the device, turn it off, and store it in a cool and dry place. Recharge the device at least every 3 months to prevent battery damage from deep discharge.
3. Storage and Maintenance
- Store and operate this device only in room temperature environments.
- Do not place the charging station near heat sources (e.g., radiators).
- To reduce the risk of electric shock, unplug your dust collector before cleaning or maintaining the product.
- Clean only with a cloth dampened with water.
- Do not place anything on this device.
- Do not expose or disassemble the electronics of this device, its battery, or the integrated charging station. There are no user-serviceable parts inside. Refer servicing to qualified personnel.
- If you need to transport the product, ensure the device is turned off and it is recommended to use the original packaging.
4. Package List
The package includes:
- L6 Pro Robot Vacuum Cleaner
- Dust Collection Charging Station
- 2-in-1 Water Tank
- Mop Cloth Holder
- Mop Cloth x2
- Disposable Mopping Cloth x10
- Dust Bag x5
- Filter Screen x2
- Main Brush
- Side Brush x2
- Cleaning Tool
- User Manual
5. Product Information
Robot Vacuum Cleaner Components
- Infrared Sensor
- Bumper
- Charge/Indicator Button: Short press to charge.
- Power Button/Indicator: Press and hold for 3 seconds to turn on/off. Short press to start or pause cleaning.
- Lidar
- Anti-collision Strip
- Infrared Sensor
Indicator Reminders
| Machine Status | Operation Indicator Status | Charging Status Indicator |
|---|---|---|
| Stand by/pause | Blue light steady | Light off |
| Charging | Blue light breathing | Light off |
| Pause | Blue light slow blink | Light off |
| Cleaning/Remote Control | Blue light steady | Light off |
| Abnormal | Red light fast flash | Light off |
| Shut down | Blue light fast flash | Light off |
| Wi-Fi not connected | Blue light slow flash | Light off |
| Wi-Fi connected | Blue light steady | Light off |
| Wi-Fi connecting | Blue light steady | Light off |
| Charging | Light off | Orange light steady |
Indicator Status Definitions:
- Breathing: Gradually turns on and off within 4 seconds.
- Slow blink: On for 0.7 seconds, off for 0.8 seconds.
- Faster flashing: On for 0.1 seconds, off for 0.2 seconds.
Device Components Diagram Description
Robot Vacuum Cleaner Parts:
- 1. Mop Cloth Mount
- 2. Main Brush Cover
- 3. Main Brush
- 4. Side Wheel
- 5. Side Brush
- 6. Caster
- 7. Cliff Sensor
Charging Station Parts:
- 1. Charging Electrode Tip
- 2. Reset Button (Hold for 1 second to restart)
- 3. Dust Bin Release Button
- 4. Position-Sensitive Wall-Following Detector
6. Maintenance
4.1 Replace the Dust Bag
- Open the top cover.
- Pull the dust bag handle up and remove the dust bag.
- Dispose of the used dust bag.
- Install a new dust bag.
- Close the top cover.
Dust Bag Indicator:
- Dust bag full: The light is bright.
- Dust bag not installed correctly: The light flashes.
- During dust collection: The lamp is bright and flashing.
- Full power: Green steady light with two grids. Power ≤50%: Green steady light with one grid.
When the dust bag is full, the "FULL UP" indicator stays bright, and an app notification is displayed. Please replace the dust bag promptly.
When the collector is operating, the "COLLECTING" indicator lights up.
4.2 Clean the Dust Passage
- (Diagrams illustrate steps: Open top cover, pull dust bag handle, remove dust bag, discard, install new bag, close top cover).
- If all indicators flash after replacing the dust bag, it is recommended to unplug the power and turn the dust collection charging station upside down to check if foreign objects are blocking the dust passage.
- If the dust channel is blocked, remove the transparent cover of the dust channel with a screwdriver to remove foreign objects.
4.3 Clean the Infrared Lens/Charging and Dust Collection Sensor Head
Wipe them gently with a clean, soft, dry cloth. It is recommended to clean them once a month.
4.4 Clean the Fan Filter Screen
The fan filter screen is located below the dust bag. If dust accumulates, gently wipe it with a clean, soft, dry cloth. It is recommended to clean it once a month.
4.5 Clean the Main Brush
The main brush is a consumable part and should be cleaned at least once a week. It is recommended to replace the main brush every 6-12 months to ensure cleaning effectiveness.
- Turn the robot vacuum over, press the pressure button on the main brush cover, and remove the main brush cover and the main brush.
- Cut the hair tangled on the main brush with the cleaning tool.
- Replace the main brush and the main brush cover. Press and secure the pressure button.
4.6 Clean/Replace the Side Brush
The side brush is a consumable part. It is recommended to replace it every 3-6 months to ensure cleaning effectiveness. Remove or install the side brush using a screwdriver.
4.7 Clean the Sensors
It is recommended to gently wipe each sensor every week with a clean, soft, dry cloth to ensure the normal use of the device.
Robot Vacuum Cleaner Sensors:
- Cliff Sensor x4
- Infrared Sensor x3
- Charging Electrode Tip x2
- Wall-Following TOF-Sensitive Detector x1
Charging Station Sensors:
- Infrared Lens x2
- Charging and Dust Collection Sensor Head x2
7. Battery Maintenance
The robot vacuum cleaner has a built-in high-performance rechargeable Lithium-ion battery. To maintain battery performance, please keep the battery charged daily.
If the device is not used for a long time, please turn it off and store it properly. Recharge it at least every 3 months to prevent battery damage from deep discharge.
8. Cleaning the 2-in-1 Water Tank
- Press and hold the release button of the 2-in-1 water tank and pull it outwards simultaneously.
- Open the dust bin by pressing the dust bin's pressure button.
- Remove the filter screen clip.
- Remove the filter screen.
- Remove dirt from the filter screen and screen clip with a cleaning brush.
- Turn on the faucet to clean the dust bin. (Tips: It is recommended to use pure water without detergent.)
- Open the water tank lid and add an appropriate amount of water. (Tips: It is recommended to use pure water without detergent.)
- Please remove the water tank fittings from the machine as shown in the figure and turn them over to remove or replace the mop.
Tips:
- If the mop is too dirty, the mopping effect will be affected; please clean it promptly.
- Remove the mop for cleaning and dry it before installation. It is forbidden to clean the 2-in-1 water tank itself.
- The mop is a consumable part and it is recommended to replace it every 3-6 weeks.
9. Specifications
Robot Vacuum Cleaner Specifications
| Product Name | Robot Vacuum Cleaner / Intelligent Cleaning Robot Vacuum Cleaner |
|---|---|
| Product Model | L6 Pro |
| Product Dimensions | 349 x 100 x 353 mm |
| Input Voltage | 24V 1.2A |
| Rated Power | 50W |
| Operating Voltage | 14.4V |
| Battery Type | Lithium-ion Battery Pack |
| Battery Capacity | 5200mAh |
| Wireless Connection | WLAN IEEE 802.11b/g/n 2.4 GHz |
Dust Collection Charging Station Specifications
| Output | 24V = 1.2A |
|---|---|
| Rated Power | 950W |
| Product Dimensions | 253 x 210 x 350 mm |
10. Troubleshooting
If the device is not running normally, the operation indicator will flash orange, and the device will issue a voice prompt when some errors occur. Refer to the table below for solutions.
| Voice Prompt/Error Phenomenon | Possible Cause | Solution |
|---|---|---|
| Please check if the Lidar is stuck | Please check if the Lidar is stuck | Remove the obstacle or place the machine in an open area and restart it. |
| Please check the anti-collision rail | The bumper sensor is stuck | Clean foreign objects around the anti-collision rail or move the machine away. |
| Please wipe the cliff sensor and move away from the danger zone to restart | The cliff sensor is triggered after the machine starts | Please wipe the cliff sensor and place the machine in a flat and open area to start. |
| Please check the main brush | The main brush is stuck | Clean the main brush or move the machine away. |
| Please check the side brush | The side brush is stuck | Clean the side brush or move the machine away. |
| Please check the main wheel | The main wheel is stuck | Clean the main wheel or move the machine away. |
| The 2-in-1 water tank is removed | The 2-in-1 water tank has been removed | Please replace the 2-in-1 water tank and the filter screen, and ensure that the filter screen and the 2-in-1 water tank are installed. |
| Low battery, start charging | Low battery during cleaning | Low battery status. Please charge the robot before use. |
| The fan is abnormal | The fan is abnormal | Please try to turn off the device and then restart it. |
| Please wipe the wall-following position-sensitive detector on the right side | The wall-following position-sensitive detector is abnormal | Please wipe and clean the wall-following position-sensitive detector. |
| The Lidar cover is pressed | The Lidar cover is stuck | The Lidar is pressed or stuck. Please move it to another position to start. |
| The battery is damaged or not installed | The battery has an anomaly during charging or is too low. | Wait until the battery temperature returns to normal before using it. |
| The machine cannot be started | Low battery level or abnormal ambient temperature. | The battery level is low. Please charge it before use. The ambient temperature is too low (below 0°C) or too high (above 50°C). Please use the product in an environment of 0°C to 40°C. |
| Cannot charge | Charging electrode tip of the machine and the dust collection and charging sensor head of the dust collection and charging station are dirty or have poor contact. | 1. Please ensure the power cord of the dust collection charging station is connected to the power supply. 2. Regularly clean the charging electrode tip of the machine and the dust collection and charging sensor head of the dust collection and charging station. 3. Please eliminate the poor contact caused by the side brush or other foreign objects, and try to reposition the machine manually. |
| Charging failed, dust collection station not found | The dust collection station is blocked or too far away; the dust collection station is not connected to the power supply; there are foreign objects at the bottom of the mop cloth holder, or the mop cloth is rolled up. | Please place the dust collection charging station in an open area and place the device near the dust collection charging station to try again. Please connect the dust collection charging station to the power supply; please clean the bottom of the mop cloth holder and tidy up the mop cloth. |
| Abnormal behavior | Program exception | Turn off and restart. |
| Unusual noises are heard during cleaning | Foreign objects are tangled on the main brush/side brush or main wheel. | Turn off the device for cleaning. |
| Cleaning performance is reduced or dust falls off | The dust bag is full or the filter screen is clogged, or the main brush is tangled. | Please clean the dust bag, filter screen, and main brush promptly. |
| Regular cleaning does not work | Low battery status. | Regular cleaning can only start when the remaining battery charge is more than 30%. Please keep the machine charged every day. |
| Cannot connect to APP | Abnormal Wi-Fi network, incorrect Wi-Fi password, or abnormal APP. | Please ensure the device is in a good Wi-Fi signal area; re-enter the Wi-Fi password or reset Wi-Fi; download the latest version of the APP and connect it. |
| The floor mopping module dispenses no or little water | Too little water in the water tank, mop cloth too dirty, or the mop cloth holder is not attached. | Please check if there is water in the water tank; clean the mop cloth; and install the mop cloth correctly according to the instructions. |
| The floor mopping module dispenses too much water | The water tank cover is not attached, and the water output is set to maximum. | Please ensure the water tank cover is attached and set the appropriate water volume in the APP. |
| Dust collection performance decreases | Dust accumulates in the dust bag, reducing airflow into the suction nozzle. | Replace the dust bag. |
| Cannot return to the dust collection charging station after spot cleaning or moving | The robot creates a new map, or the distance is too large. | After spot cleaning or a long movement, the robot generates a new map. If the dust collection station is far away, the robot may not be able to charge automatically. Please manually return the device to the dust collection charging station for charging. |
| Dust suction failed | The dust bag is missing or not installed. The dust bag is full or clogged. The fan starts overheating protection or has errors. | Please install the dust bag correctly and try collecting dust again after 30 minutes. If the problem cannot be resolved, please contact customer service. Replace the dust bag and clean the dust collection charging station (suction inlet, dust passage, fan filter screen, etc.) promptly. |
11. Warranty
1-Year Limited Warranty
Your Laresar machine is warranted for 1 year against original defects in material and workmanship when used in a household manner according to the Laresar operating instructions.
What is Covered?
Subject to the following conditions and exclusions, in accordance with the requirements in this user manual.
- Only applies to purchases made from authorized Laresar dealers.
- This warranty is valid only when the machine is used in the country in which it was sold.
What is Not Covered?
Laresar is not liable for costs, damages, or repairs incurred as a result of:
- Machines purchased from an unauthorized dealer.
- Careless operation or handling, misuse, abuse, and/or lack of maintenance or use not in accordance with the Laresar user manual.
- Machines used for commercial or rental purposes in addition to normal household use.
- Use of parts that do not comply with the Laresar operating manual.
- Use of parts and accessories not manufactured or recommended by Laresar.
- External factors unrelated to product quality and use, such as accidental water damage.
- Repairs or alterations performed by unauthorized parties or representatives.
- Normal wear and tear, including water tank, filter, HEPA, main brush, side brush, and power cord (or if external damage or misuse is diagnosed), carpet or floor damage due to use not in accordance with manufacturer's instructions, or failure to rotate the brush roller as needed.
- Shortening of battery discharge time due to battery age or usage.
How to Claim?
Please keep your proof of purchase. To make a claim under our limited warranty, you must present your original proof of purchase with the date of purchase and order number.
- All work will be performed by Laresar or its authorized agency.
- All replaced defective parts will become the property of Laresar.
- Service under this warranty does not extend the term of this warranty.
12. Disposal
This product must not be disposed of via household waste. Dispose of the device at an authorized collection point for the recycling of electrical equipment. The chemicals contained in the product's Lithium-ion battery pollute the environment. Please remove the battery before scrapping and take it to a professional battery recycling station for centralized disposal.
Steps for Battery Removal
The following information applies only to the disposal of the sweeping and mopping robot and not to daily operation.
- Turn off the robot vacuum.
- Unscrew the bottom cover of the cleaning robot and remove the bottom cover.
- Pull out the battery connector plug and remove the battery.
Notes:
- Handle the battery carefully to avoid leakage of hazardous substances.
- If the battery leaks, flush the affected area with plenty of water and seek medical attention promptly.
