TITAN TTS1070VAC 3.7V Window Cleaner
Safety Warnings
General Safety
This appliance can be used by children aged 8 and above, and persons with reduced physical, sensory, or mental capabilities if they have been given supervision or instruction on safe use and understand the hazards. Children must not play with the appliance. Cleaning and maintenance by children should only be done with supervision.
Window Cleaner Specific Safety
- Never spray water or liquids directly at electrical devices or components (e.g., TV, radio, ovens).
- Do not leave the appliance unattended while connected to the mains.
- Do not use if dropped, damaged, or leaking.
- Turn off and disconnect from charger before emptying the dirty water tank.
- Use the appliance only in its upright position.
- Do not use corrosive chemicals or products containing bleach.
- Use only original spare parts from the manufacturer or approved ones.
- Use only with regular no-foam window cleaning agents.
- Never use outdoors in the rain.
- Wear appropriate Personal Protection Equipment (PPE), e.g., eye protection.
- Take particular care when using the product at height; do not lean out of windows.
- Use only for its intended purpose; do not direct liquid towards people or animals.
- Do not insert objects into the vacuum aperture.
- Test detergents on an inconspicuous area if compatibility is uncertain.
- Do not use undiluted acids, acetone, solvents, or flammable liquids.
- Do not use boiling or hot water.
- Do not submerge the appliance or its electrical parts in water or other liquids.
- The product contains a non-replaceable battery.
- Remove the plug from the socket-outlet before cleaning or maintenance.
- Use only the provided power supply unit.
Battery Pack and Charger Safety Instructions
- Recharge only with the manufacturer-specified charger.
- Avoid contact with battery liquid if ejected under abusive conditions; flush with water if contact occurs.
- Do not place appliances or batteries near fire or heat sources.
- Batteries can explode near ignition sources; avoid open flames.
- Do not charge in damp or wet locations.
- Optimal charging temperature is 18°C to 24°C; avoid below 4°C or above 40°C.
- Do not disassemble the battery or cause mechanical damage; risk of short circuit and fumes. Ensure fresh air and seek medical help if discomfort occurs.
- Charger Safety: Do not subject to strong sunlight or heat. Allow hot battery to cool before charging. Do not use non-rechargeable batteries. Charge only supplied appliances. Check charger cable/plug; do not use defective ones. Protect charger from moisture. Operate charger only with appropriate original batteries. Avoid mechanical damage to the charger. Do not operate on flammable surfaces. Do not abuse charger cord. Keep cord away from heat, oil, sharp edges. Do not operate with damaged cord/plug.
- Battery is not fully charged on delivery; charge fully before first use.
- Do not use a dropped or damaged charger.
- Ensure voltage matches power source.
- Never touch mains plug with wet hands.
- Unplug charger when not in use.
Vibration and Noise Reduction
To reduce impact of noise and vibration emission, limit operation time and wear personal protective equipment.
Minimize risks by:
- Using the product as intended.
- Ensuring the product is in good condition and well maintained.
- Using correct, well-conditioned accessories.
- Keeping a tight grip on handles.
- Maintaining and lubricating the product as appropriate.
- Planning work schedules to spread high vibration tool use.
- Prolonged use can cause Hand-Arm Vibration Syndrome (HAVS). Wear protective gloves and keep hands warm.
Emergency
Familiarise yourself with the product and memorize safety directions. Be alert and handle risks early; fast intervention prevents serious injury.
Switch off if malfunctions occur and have the machine checked by a qualified professional.
Residual Risks
Even with correct use, risks remain:
- Health defects from prolonged vibration emission or inadequate maintenance.
- Injuries/damage from broken attachments or impact of hidden objects.
- Danger from flying objects.
WARNING! This product produces an electromagnetic field. It may interfere with active or passive medical implants. Consult your doctor and the medical implant manufacturer before operating if you have implants.
Your Product
The product is the TITAN TTS1070VAC 3.7V Window Cleaner.
Key Components:
- 1. Suction attachment: Includes a rubber strip (1a) and an attachment lock (1b). It connects to the suction port (1c).
- 2. Dirty water tank: Features a water tank lock (2a), an easy empty plug (2b), the water tank itself (2c), an inter-connection part (2d), and a max fill mark (2e). It has a capacity of approximately 100 ml.
- 3. Charger status indicator: Shows charging status.
- 4. Charger socket cover: Protects the charger socket (4a).
- 5. On/off switch: Controls the power.
- 6. USB-C cord: Used for charging.
[Info] Parts marked with an asterisk (*) are not shown in this overview and are detailed in other sections of the manual.
Technical Specifications
General
- Rated voltage: 3.7 V
- Number of batteries: 1
- Input: 5.0V d.c. 2.0A Max
- Max. suction power: 1.5-1.7 Kpa
- Rated power: 20 W
- Protection class: IPX4 (protected against water splashing)
- Dirty water tank capacity: 100 ml (max. level)
- Weight: 0.76 kg
Battery Pack
- Rated voltage: 3.7 V
- Rated capacity: 2200 mAh
- Battery type: Li-ion
Symbols Explained
- V~: Volt (alternating voltage)
- V: Volt (direct current voltage)
- Hz: Hertz
- W: Watt
- A: Ampere
- mAh: Milliampere-hour
- kg: Kilogram
- dB(A): Decibel (A-rated)
- m/s²: Metres per second squared
- IPX4: Protection against water splashing.
- yyWxx: Manufacturing date code (year and week).
- [Lock]: Lock / to tighten or secure.
- [Prohibited]: Not for outdoor use.
- [Unlock]: Unlock / to loosen.
- [Info]: Note / Remark.
- [Warning]: Caution / Warning.
- [Manual]: Read the instruction manual.
- [Eye Protection]: Wear eye protection.
- [Respiratory Protection]: Wear respiratory protection.
- CE / UKCA: Product complies with applicable European directives.
- [WEEE Symbol]: Waste electrical products should not be disposed of with household waste; please recycle.
- [Recycle Battery Symbol]: Batteries and battery packs should not be disposed of with household waste; please recycle. Batteries contain Lithium-ion.
Rating Label Explanation:
- TTS1070VAC = Model number
- TT = TITAN
- S = 3.7V DC
- 1070 = Version number
- VAC = Vacuum
Before You Start
Unpacking
- Unpack all parts and lay them on a flat, stable surface.
- Remove all packing materials and shipping devices.
- Check that delivery contents are complete and free of damage. If missing or damaged, contact your dealer.
- Ensure you have all necessary accessories, tools, and suitable personal protective equipment.
WARNING! The product and packaging are not children's toys. Keep away from children due to danger of choking and suffocation.
You Will Need
- Items not supplied: Adapter, Suitable personal protective equipment.
- Items supplied: Suction attachment (1), USB-C cord(6).
Assembly
WARNING! The product must be fully assembled before operation. Do not use if partly assembled or with damaged parts. Follow assembly instructions step-by-step using provided pictures.
[Info] Take care of small parts removed during assembly or adjustments; keep them secure.
Suction Attachment Assembly
Attaching: Align the suction attachment (1) to the suction port (1c). Push it in until it clicks. Ensure the attachment lock (1b) engages properly.
Detaching: Press and hold the attachment lock (1b). Pull out the suction attachment (1).
Charger
Use a suitable adapter (output: 5V 2.0A Max) to charge the battery.
WARNING! Do not charge the product with liquid in the dirty water tank (2).
The battery is shipped in a low charge condition; charge it fully before first use. Only charge with the correct charger.
Open the charger socket cover (4). Attach the USB-C cord to the charge socket (4a) and ensure it is properly engaged.
Connect the adapter plug to a suitable power supply.
The charging status is indicated by the charging status indicator (3):
- Flashing blue light: Charging
- Steady blue light: Charging finished
[Info] It is normal for the charger to become warm (but not hot) during charging.
When the battery is fully charged, disconnect the adapter and reinstall the charger socket cover (4).
In More Detail
Product Functions
Intended Use
The product is designated for domestic use to vacuum liquids from smooth, non-porous surfaces such as glass, mirrors, and tiles. It is not suitable for vacuuming dust, cleaning horizontal surfaces, or use on surfaces that are not vertical or near vertical. Use detergents designed for window vacuum machines.
Read the entire instruction manual before first operation.
Dirty Water Tank
Liquid is collected in the dirty water tank (2). Empty the tank when the water level reaches the max. mark (approx. 100 ml).
CAUTION! The upper and lower tanks are not permanently connected; operate carefully to avoid spilling liquid.
Detaching the Dirty Water Tank
Press the water tank lock (2a) to pop the tank up slightly. Remove the dirty water tank (2). Open the easy empty plug (2b), tilt the tank, and pour out the dirty water.
Attaching the Dirty Water Tank
Close the easy empty plug (2b). Press the water tank lock (2a) and reinstall the dirty water tank (2) until it clicks securely.
On/Off Switch and Operation
Switch the product on or off by pressing the On/off switch (5).
[Info] Only use the appliance with regular no-foam window cleaning agent.
WARNING! Do NOT place the window vac on polished or delicate surfaces.
[Info] Always follow dilution and concentration instructions for cleaning agents.
WARNING! Before each use, check the suction attachment for dirt residues that might scratch the surface. If dirty, wipe with a clean, damp cloth.
Press the On/off switch (3) to turn on the product. Place the suction attachment (1) at the top of the surface to be cleaned. Move the product slowly down the surface, ensuring the rubber blade stays in contact. Water and detergent residue will be sucked into the dirty water tank (2).
[Info] Water may come from the vents; this is normal.
Operation Continued
Continue cleaning along the surface, overlapping previous strokes, until the whole surface is complete.
WARNING! Move the product from top to bottom. Do not slide it horizontally.
If the water level reaches the max. mark, switch off the product and empty the dirty water tank (2).
Tips
- Switch off the product before removing the dirty water tank (2).
- Pay attention to the pressure applied on the surface; do not damage it.
- Observe the liquid flow down the surface.
- The appliance is not intended for vacuuming fluids from horizontal surfaces.
- Do not use on glass with uneven surfaces (frosted, textured, patterned).
- Do not use on cracked or broken windows.
After Use
Press the On/off switch (3) to turn off the product. Disassemble and empty the dirty water tank (2) if necessary. Check, clean, and store the product as described below.
Care and Maintenance
The Golden Rules for Care
WARNING! Always switch the product off and let it cool down before performing inspection, maintenance, or cleaning.
- Keep the product clean; remove debris after each use and before storage.
- Regular, proper cleaning ensures safe use and prolongs product life.
- Inspect the product for worn and damaged parts before each use. Do not operate if parts are broken or worn.
WARNING! Only perform repairs and maintenance according to these instructions. All further work must be done by a qualified specialist.
General Cleaning
Clean the product with a slightly damp cloth and mild soap. Use a brush for hard-to-reach areas.
[Info] Do not use chemical, alkaline, abrasive detergents, or disinfectants, as they may harm surfaces.
Check for any damage and wear. Repair damages or take the product to an authorized service centre.
Suction Attachment
Disassemble the suction attachment (1). Clean the chamber and rubber strip (1a) with water. Dry the entire suction attachment (1) before reassembling.
Dirty Water Tank
WARNING! Do not fill with boiling or hot water.
Empty and assemble the dirty water tank (2) in reverse order of the instructions. Ensure parts are aligned and securely reassembled.
Maintenance
Before and after each use, check the product and accessories for wear and damage. Exchange parts if required, following technical requirements.
Repair
This product contains no user-repairable parts. Contact an authorized service centre or qualified person for checks and repairs.
Storage
Switch the product off. Clean if necessary. Store in a dry, frost-free place, inaccessible to children. Ideal storage temperature is 10°C to 30°C. Use original packaging or a cover to protect from dust.
Transportation
Switch the product off. Clean if necessary. Protect from heavy impact or strong vibrations during transport. Secure the product to prevent slipping or falling.
Troubleshooting
Suspected malfunctions can often be fixed by users. Check the product using this section.
WARNING! Only perform steps described in these instructions. Further work must be done by an authorized service centre or specialist.
| Problem | Possible Cause | Solution |
|---|---|---|
| 1. Product does not start | 1.1. Battery discharged 1.2. Battery too hot/cold 1.3. Other electrical defect | 1.1. Recharge battery 1.2. Allow to cool/warm 1.3. Contact nearest authorised service centre |
| 2. Restricted or no vacuum | 2.1. Suction attachment blocked 2.2. Dirty water tank not assembled properly | 2.1. Unblock suction attachment 2.2. Reassemble the dirty water tank properly |
| 3. Product turns itself off | 3.1. Battery too hot/cold | 3.1. Allow to cool/warm |
| 4. Battery will not charge | 4.1. Battery charger not connected correctly 4.2. Battery too hot/cold | 4.1. Check battery charger connection 4.2. Allow to cool/warm |
| 5. Streaking on windows | 5.1. Rubber strip damaged 5.2. Too much force applied 5.3. Too little force applied | 5.1. Replace rubber strip 5.2. Apply reduced force 5.3. Apply more force |
Recycling and Disposal
[WEEE Symbol] Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
For further information visit www.recycle-more.co.uk.
The product packaging protects it during shipping. Keep it until you are sure all parts are delivered and the product is working properly. Recycle the package afterwards.
Disposal of an Exhausted Battery Pack
The battery is Li-ion type. To preserve natural resources, please recycle or dispose of the battery pack properly. Consult your local waste authority for recycling/disposal options.
Discharge your battery pack by operating your tool, then remove the battery pack. Cover the battery pack connections with heavy-duty adhesive tape to prevent short circuit and energy discharge. Do not attempt to open or remove any components.
Guarantee
This TITAN 3.7V Window Cleaner has a 2-year manufacturer's guarantee against manufacturing defects from the date of purchase or delivery. This applies to normal household use at no additional cost.
To make a claim, present proof of purchase. The guarantee applies to new products only.
The guarantee covers product failures and malfunctions if the product was used as intended and maintained according to the manual and standard practice.
The guarantee does NOT cover:
- Normal wear and tear.
- Damage from improper use, faulty installation/assembly, neglect, accident, misuse, or modification.
- Ancillary costs (shipping, labour, etc.) or direct/indirect damage.
- Repairs attempted by anyone other than an authorised agent.
- Cosmetic damage.
- Damage caused by foreign objects, substances, or accidents.
- Accidental damage or modification.
- Failure to follow manufacturer's guidelines.
- Loss of use of the goods.
If the product is defective, it will be repaired or replaced within a reasonable time. Rights under this guarantee are enforceable in the country of purchase.
The guarantee is in addition to and does not affect your statutory rights.
Manufacturer Information
UK manufacturer: Kingfisher International Products Limited, 1 Paddington Square, LONDON, W2 1GG, United Kingdom. Visit www.kingfisher.com/products.
EU manufacturer: Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM Amsterdam, The Netherlands. Visit www.diy.com, www.screwfix.com, or www.screwfix.ie.
[EN] To view instruction manuals online, visit www.kingfisher.com/products.
