MOMAN CP2 1-Trigger-2 Wireless Phone Microphone User Manual

Caring For Your MOMAN Product

• Please keep the product in a dry, clean, dust-free environment.
• Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage.
• Use only a soft and dry cloth for cleaning the product.
• Malfunction may be caused by dropping, impact of external force.
• Do not attempt to disassemble the product. Doing so voids warranty.
• Please have the product checked or repaired by authorized technicians if any malfunctions happened.
• Failure to follow all the instructions may result in mechanics damage.
• Warranty does not apply to human errors.

Package List

The MOMAN CP2 package includes:

• TX Transmitter (x2)
• RX Receiver (x1) [x2 for CP2(AC)]
• Charging Case (x1)
• Type-C Charging Cable (x1)
• Type-C to USB Adapter (Not included with CP2(A))

A visual representation shows the individual components: two transmitters, one receiver, a charging case, a Type-C charging cable, and an optional Type-C to USB adapter.

Product Introduction

The following describes the components of the MOMAN CP2 system:

Transmitter Components:

1. Foam Windscreen
2. Transmitter Indicator Light
3. Transmitter Charging Port
4. Clip
5. Power/Mute Button

Receiver Components:

6. Phone Connector (Type-C or Lightning)
7. Receiver Indicator Light
8. Type-C or Lightning Port
9. Strap Hole

Charging Case Components:

10. Charging Case Indicator
11. Type-C Charging Port

A diagram illustrates the front and side views of the transmitter, receiver, and charging case, with numbered callouts corresponding to the component descriptions above.

Indicator - TX Transmitter

Indicator - RX Receiver

Indicator - Charging Case

Operation

TX Transmitter Operation

1. Power On/Off

• On: Press the Power/Mute Button once.
• Off: Long press the Power/Mute Button for 3s.

2. Pairing

With two transmitters ON, plug the receiver into the device and the system will pair automatically.

* If the TX and RX are not connected or if replacement of the RX is needed, re-pairing is required.

1. With one TX ON, long press the Power/Mute Button for 8s until the green light flashes quickly. Plug in the RX until the green light is on.
2. Plug out the RX. Follow step (1) to pair the other TX and plug in the RX again until the green light is on. When indicators of both TX show green, two-transmitter-one-receiver pairing is successful.

Note:

Before TX pairing, do not plug RX into the device and power it. Otherwise, the pairing may not be successful.

3. Mute

After pairing, press the Power/Mute Button once to mute. Press it again to cancel mute.

4. Charging

Place the TX in the case with contacts connected with the case's charging points or charge them via charging cable. Please fully charge the TX transmitter with the charging cable before use.

RX Receiver Operation

1. Power On/Off

• On: Plug in the device.
• Off: Plug out of the device.

2. Connecting

Connect the receiver to the phone.

• Use the Type-C to USB Adapter to connect with a computer.
• OPPO/VIVO/IQOO/Realme mobile phones can be used normally only when OTG function is enabled (please search "OTG" in the settings to enable).

3. Pairing

With two transmitters ON, plug the receiver into the device and the system will pair automatically.

4. Charging

There is no battery in the RX receiver and no need to recharge during live use. If the phone is low on power during live use, it can be recharged directly through the Type-C or Lightning port on the RX receiver.

* Some models do not support this function.

Charging Case Operation

Charging

Connect the case with power supply via the charging cable.

* When two transmitters are put in the charging case again, the green lights are ON, displaying the remaining battery.

A diagram illustrates the charging case with a phone connected, showing the Type-C port for charging the phone and the case itself.

Specifications

TX Transmitter Specifications

RX Receiver Specifications

Charging Case Specifications

General Specifications