Pioneer TS-WX1210AM Active Subwoofer

Important Safety Information

Hearing Protection

Play audio at safe levels. Prolonged exposure to high volume can cause permanent hearing loss. Establish a safe listening level by setting the volume control low and slowly increasing it until sound is clear and comfortable, without distortion. Once set, leave the volume at that level.

Guidelines:

• Ensure you can still hear surrounding traffic noises.
• Exercise caution or discontinue use in hazardous situations.
• Do not use headphones while operating a vehicle, as it is a traffic hazard and illegal in many areas.

Installation Warnings

• Before installation, disconnect the vehicle's negative (-) battery power cable to prevent electrical shock.
• Use supplied connecting cords and do not remove fuses; the protection circuit relies on them.
• Install the speaker where it won't obstruct passengers or pose a danger during sudden stops.
• Before drilling, check behind the mounting location for gas lines, brake lines, or electrical wiring.
• Do not install the TS-WX1210AM in areas that can get wet.
• Use only supplied parts for secure installation.
• Do not insert hands or objects into the duct to avoid injury or damage.
• Avoid installing in unstable areas prone to vibration, which could cause detachment and damage or injury.
• While driving, maintain a listening volume that allows you to hear important external traffic sounds like emergency vehicles.
• High sound levels can cause permanent hearing loss.

Cautionary Notes

• This device operates on a 12-volt (-) negative ground system. Verify your vehicle's compatibility.
• Secure all wiring with cable retainers, adhesive tape, or shrink tubing where they might contact sharp edges. Keep wiring away from hot surfaces or heater outlets to prevent short circuits.
• Refer to your car stereo's operation manual during installation.
• Correctly set the input level switch to match your car stereo's output to avoid distortion and ensure proper volume.
• Low-frequency noise from the head unit may be amplified by the TS-WX1210AM.

Features

• High output and deep bass reproduction.
• Compact design for easy installation in various vehicle spaces.
• Built-in amplifier for powerful sound.
• Includes a wired remote control for convenient adjustment of volume and other settings.

Connections

The subwoofer can be connected using either RCA line-level inputs or speaker-level inputs from the car stereo.

RCA Input Connection:

Connect the RCA cables from the car stereo's pre-out (front or rear) to the RCA L/R inputs on the subwoofer. Connect the remote turn-on wire from the car stereo to the REM terminal on the subwoofer.

Speaker Level Input Connection:

Connect the speaker wires from the car stereo's rear speaker outputs to the Speaker Level L/R inputs on the subwoofer. Connect the power (BATT), ground (GND), and remote turn-on (REM) wires to the appropriate vehicle power sources.

Diagram Description: Two connection diagrams are provided. One shows RCA cables linking the car stereo's pre-outs to the subwoofer's RCA inputs. The other shows speaker wires from the car stereo's speaker outputs connecting to the subwoofer's speaker-level inputs. Both diagrams illustrate connections for power (BATT, GND, REM) and the wired remote control.

Controls and Use

The subwoofer features several controls for sound adjustment:

• GAIN: Adjusts the input sensitivity to match the car stereo's output level.
• LPF (Low Pass Filter): Sets the crossover frequency, typically between 50Hz and 200Hz, to control which low frequencies are sent to the subwoofer.
• PHASE: Selects between 0° and 180° phase to optimize bass response with the car's main speakers.
• BASS BOOST: Enhances bass frequencies.
• Wired Remote Control: Allows for on-the-fly adjustment of the subwoofer's volume.

Diagram Description: A diagram shows the top panel of the subwoofer with labeled control knobs: GAIN, LPF, PHASE, and BASS BOOST. It also indicates the location of the wired remote control port. The separate wired remote control unit has a prominent volume knob.

Specifications

Key specifications for the TS-WX1210AM:

Graph Description: A frequency response graph illustrates the subwoofer's output level across different frequencies. It shows a strong output in the low-frequency range (e.g., 50-100Hz) with a gradual decrease at higher frequencies.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation.

Alterations or modifications without authorization may void the user's right to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. If interference occurs, users are encouraged to try correcting it by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment to an outlet on a different circuit than the receiver.
• Consulting the dealer or an experienced radio/TV technician.

Supplier's Declaration of Conformity:

Product Name: ACTIVE SUBWOOFER

Model Number: TS-WX1210AM

Responsible Party: PIONEER ELECTRONICS (USA) INC.

Address: 2050 W. 190th STREET, SUITE 100 TORRANCE, CA 90504, U.S.A.

Phone: 1-800-421-1404

URL: http://www.pioneerelectronics.com

Canadian models comply with CAN ICES-3 B/NMB-3 B.