Suraielec Smart Wi-Fi Box Timer Switch

Safety Section

WARNING

Risk of Fire or Electrical Shock

• This smart box should be installed by a licensed electrician.
• Turn power off at the main panel before servicing this switch or the equipment it controls.
• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.
• Installation and/or wiring must be in accordance with national and local electrical code requirements.
• This enclosure does not provide grounding between conduit connections. When metallic conduit is used, you must also install grounding type bushings and jumper wire.
• Use #14-#8 AWG wires, rated at least 75°C (167°F) - COPPER conductors ONLY.
• Make sure there is no wire insulation under the terminal plate on the timer switch connector. Firmly tighten terminal screws.
• Do not remove the insulator that is covering terminals.
• KEEP THE DOOR CLOSED AT ALL TIMES when not servicing.
• Installation, Operating and Safety Instructions - Instructions for installation and use of this product are provided by the manufacturer. "Make sure to use this product together with 40A circuit breaker in the upstream" stated in the manual.

Specifications

Input

120-240/277VAC, 60Hz. Detects voltage automatically (NO DIP SWITCH SETTING REQUIRED)

Contact Ratings

• 40A Resistive 120 to 277 VAC;
• 30A General Purpose 120 to 277 VAC;
• 20A Resistive, 30VDC;
• 1HP, 120 VAC;
• 2HP, 240VAC;
• 20A Ballasted load 120 to 277 VAC;
• 15A Tungsten, 120 VAC;
• 5A Tungsten, 250VAC;
• 800VA, Pilot Duty, 120VAC;
• 720VA, Pilot Duty, 240 VAC;
• TV-5, 120VAC

System

• Wireless Type: 2.4GHz Only IEEE 802.11 b/g/n
• Wi-Fi Range: 80Ft (Free Area)
• APP: Smart life
• iOS: 8.0 or higher
• Android: 4.1 or higher

Terminal range

#14-#8 AWG

Operating temperature:

-40°F to 149°F

Product Illustration

A diagram shows the Suraielec Smart Wi-Fi Box Timer Switch. It highlights the Wi-Fi LED Indicator, Power Button & Program Button, and Plastic Insulator. It also shows knockouts for wire entry and a grounded terminal.

Light Chart

Installation

Mounting the Smart Box Timer

1. Choose the knockouts (five 1/2" to 3/4" combination knockouts available). For 1/2" Knockouts: Carefully cut off the inner ring of the rubber plug with a knife. For 3/4" Knockouts: Please remove the entire rubber plug.
2. Mounting the Smart Box Timer: Hold the box in place and use the three holes to mark position on the mounting surface. Mount the box with screws.

NOTE: Before installation, please confirm the Wi-Fi signal is strong enough. Wi-Fi range can be affected by obstructions, metal objects, distance and weather. Mount unit should be as close to the router as possible. Install upright, in a vertical orientation. Always close the rainproof door after use.

Connecting the Wires

1. Lift the plastic insulator off the retaining post to expose the terminal strip.
2. According to the wiring diagram to wire. Note: please connect the grounded wire to the grounding terminal.

FIG.5 TERMINAL DESIGNATIONS

Diagram showing terminal designations: L (Live), N (Neutral), NO (Normally Open), COM (Common Terminal), J (Jumper Wire), T (Timer).

FIG.6 120V Application - Controlling One 120VAC Load

Wiring diagram for a 120V application controlling one 120VAC load.

FIG.7 120VAC Application - Controlling Two 120VAC Loads

Wiring diagram for a 120VAC application controlling two 120VAC loads.

FIG.8 240VAC Application - Controlling One 240VAC Load

Wiring diagram for a 240VAC application controlling one 240VAC load.

FIG.9 277VAC Application - Controlling Two 277VAC Loads

Wiring diagram for a 277VAC application controlling two 277VAC loads.

FIG.10. HOT WATER HEATER TYPICAL WIRING DIAGRAM

Wiring diagram for a hot water heater typical application.

Smart Life APP Setup

NOTE: Due to continuous updates and improvements, the "Smart Life" app user interfaces may appear slightly different. In case of any differences, follow the in-app instructions.

1. Download the Smart Life APP: Scan QR Code or search "Smart Life" in Google Play or the App Store to download and install the app.
2. Open the "Smart Life" app. Tap "Register" to create a new account or Log In to log your account.
3. Tap the top right corner "+", and then choose "Socket Wi-Fi".
4. Choose your network and enter the password. Ensure you select a 2.4GHz Wi-Fi network. If your Wi-Fi is 5GHz, please set it to be 2.4GHz.
5. Long press the program button on the smart box until the blue light flash, then press the "next" button on the app step by step.

FIG.11 Download the APP: Shows QR codes for Google Play and the App Store to download the Smart Life app.

FIG.12: Shows the Smart Life app login and registration screen.

FIG.13: Shows the Smart Life app interface for adding devices, with categories like "Socket (Wi-Fi)".

FIG.14: Shows the screen to select the Wi-Fi network and enter the password.

FIG.15: Shows the smart box with the program button highlighted, and the app screen indicating to press "Next".

FIG.16: Shows the process of powering on the device and pressing the reset button until the indicator blinks.

FIG.17: Shows the device being added successfully and the indicator blinking rapidly.

FIG.18 Timer Function: Illustrates the timer functions available: Program, Countdown, Random, and Repeat.

Turning Devices On/Off

To turn the smart box ON/OFF, there are two methods:

• A. Press the power button on the smart box.
• B. Tap ON/OFF in the Smart Life APP.

Timer Function

Enter the Smart Box control interface, select "Program", "Countdown", "Random", or "Repeat" to meet your needs.

Program

Set the Start/End time in a 7-day period with a 1-minute interval according to your needs. Every program you set repeats weekly.

Countdown

Tap "Countdown" to set the hours and minutes, and then tap the "Start" button. The Smart Box will maintain the current state (on or off) until the end of the countdown. It will terminate countdown mode automatically if you turn on/off the smart box.

Random

Either +/-30 minutes than setting ON/OFF time, randomly control device when you are away from home. The setting process is the same as "Program".

Repeat

Set the duration of each ON and OFF, the start and end time according to your needs. The ON/OFF schedule will repeat between the start and end time. For example: You set a period from 6:00 AM to 11:30 AM on Mon, Thur and Fri, turn on your pump for 5 mins, and off for 10 mins. The Smart Box will repeat on/off from 6:00 AM to 11:30 AM.

Work with Alexa

Link Smart Life account to Alexa

1. Open your Alexa app, tap "Skills" in the menu, and then search "Smart Life". Select "Smart Life" and tap "Enable" to enable the Smart Life skills.
2. You will be directed to the account link page. Type in your "Smart Life" account and password, don't forget to select your country/region where your account belongs to and then tap "Link Now" to link your Smart Life account.

Control your smart devices

Discover devices: Echo needs to discover your smart devices before it controls them. You say "Alexa, discover devices" to Echo. Echo will discover devices which have already been added in the "Smart Life" app. You can also tap "discover devices" to discover the smart devices. Discovered devices will be shown in the list.

Note: Every time you change the device's name on the Smart Life app, Echo needs to re-discover the device before controlling them.

Work with Google Home/ Google Assistant

Open your Google Home app, add device in Home Control of the Google Home app. Select "Smart Life", and fill in the correct login information of your account to finish the account linking. Your device will be shown in Home Control device list.

Share Your Device

Use Share Device to allow someone else to control your smart outlet (such as family, friends, roommates, or anyone you choose).

• Select the device you want to share and press the top right corner.
• Press the Share Device, and share it with your family.

Troubleshooting

1. Why isn't my smart box connecting to the Smart Life app?
   • Confirm the signal strength is strong enough.
   • During the setup process, the smart box must be connected to a secure 2.4GHz WiFi network.
2. My Smart Box is offline.
   • Power outages, internet outages, or changing WiFi routers may cause your smart box to go offline. Check these devices first.
   • Reset and reconfigure your smart box with Smart Life APP.
3. Amazon Alexa or Google Assistant can't find my app or can't discover my smart box timer.
   • Make sure you log into the same Smart Life account as your box timer in the Alexa or Google assistant app.
   • Make sure your wireless network router is close enough to your smart box timer.
   • Check that your Amazon Alexa or Google Assistant is working properly.

Any other questions, please contact Suraielec Consumer Care, and they can provide professional solutions.

One Year Limited Warranty

Suraielec warrants to the purchaser of this product, for the period of one (1) year following the date on which Purchaser purchases the product, that the product shall be free of defects in design, assembly, material, or workmanship.

If you have any problems or questions, please contact Suraielec Consumer Care by the E-mail: surai-tech@outlook.com