ASSEMBLY INSTRUCTION
ITEM NO: 194840303886
ACCENT CHAIR / FAUTEUIL ACCENT
Thank you for purchasing this product. Please take time to read and follow the instructions below. Check that you have all parts and hardware before assembly. Parts apparently missing are often found in the packing materials. If you do not have all the parts listed, have your dealer contact us and they will be sent to you immediately.
Note: It is recommended to install protective pads under all legs and supports to avoid damage or scratches when placing furniture on a wood floor or other hard surface, and to limit indentation and prevent discoloration if placing on carpet.
Note: Hardware may loosen over time. Periodically check to make sure all connections are tight. Re-tighten if necessary.
Parts List / Liste des Pièces
| NO | SKETCH/ESQUISSER | DESCRIPTION/LA DESCRIPTION | Q'TY/Q'TE |
|---|---|---|---|
| A | [Rectangular cushion] | BACK CUSHION/COUSSIN ARRIÈRE | 1PC |
| B | [Square cushion] | SEAT CUSHION/SIÈGE COUSSINÉ | 1PC |
| C | [U-shaped frame] | BACK FRAME/CADRE ARRIÈRE | 1PC |
| D | [Rectangular frame] | SEAT FRAME/CADRE DE SIÈGE | 1PC |
| E | [Armrest with angled support] | LEFT ARM/BRAS GAUCHE | 1PC |
| F | [Armrest with angled support] | RIGHT ARM/BRAS DROITE | 1PC |
| G | [Long, thin bar] | FRONT STRETCHER/BARREAU AVANT | 1PC |
| H | [Long, thin bar] | BACK STRETCHER/BARREAU ARRIÈRE | 1PC |
Hardware List / Liste de Quincaillerie
| NO | SKETCH/ESQUISSER | DESCRIPTION/LA DESCRIPTION | SIZE/TAILLE | Q'TY/Q'TE |
|---|---|---|---|---|
| 1 | [Bolt] | BOLT/BOULON | diameter 5/16" x 60mm | 3 PCS |
| 2 | [Bolt] | BOLT/BOULON | diameter 1/4" x 50mm | 10 PCS |
| 3 | [Spring washer] | SPRING WASHER/RONDELLE D'ARRET | diameter 5/16" x 13mm | 3 PCS |
| 4 | [Flat washer] | FLAT WASHER/RONDELLE PLATE | diameter 5/16" x 19mm | 3 PCS |
| 5 | [Wooden dowel] | WOODEN DOWEL/GOUJON DE BOIS | diameter 8 x 30mm | 6 PCS |
| 6 | [Wood screw] | WOOD SCREW/VIS | M4 x 45mm | 4 PCS |
| 7 | [Allen key] | ALLEN KEY/CLE D'ALLEN | 4mm | 1 PC |
* ABOVE HARDWARE ARE PACKED IN CARTON FOR ASSEMBLY * SCREW DRIVER (NOT PROVIDED)
Assembly Steps / Étapes d'Assemblage
STEP 1/ÉTAPE 1
Connect the left arm (E) and right arm (F) to the front stretcher (G) and back stretcher (H). Insert quantity 4 wooden dowels (5) into the pre-drilled holes on the stretcher ends. Align the armrests and secure using quantity 4 bolts (2) with the Allen key (7). Do not fully tighten yet.
[Diagram shows armrests (E, F) and stretchers (G, H) being connected using dowels (5) and bolts (2), with Allen key (7) indicated. Arrows show connection points. Quantity 4 indicated.]
STEP 2/ÉTAPE 2
Attach the seat frame (D) to the bottom of the armrest assembly. Secure with quantity 2 bolts (2) and quantity 2 flat washers (4). Attach the back frame (C) to the rear of the seat frame (D) and the back stretcher (H). Secure this connection with quantity 1 bolt (1), quantity 1 spring washer (3), and quantity 1 flat washer (4).
[Diagram shows seat frame (D) and back frame (C) being attached to the structure from Step 1. Hardware (1, 2, 3, 4, 7) are indicated. Quantities 3 and 2 are shown.]
STEP 3/ÉTAPE 3
Position the seat frame (D) into the back frame (C).
[Diagram shows the seat frame (D) being lowered into the back frame (C). Arrows indicate downward movement.]
STEP 4/ÉTAPE 4
Place the seat cushion (B) onto the seat frame (D). Place the back cushion (A) against the back frame (C). Secure the cushions using quantity 2 bolts (2) and tighten with the Allen key (7).
[Diagram shows cushions (A, B) being placed on the frame. Hardware (2, 7) are indicated. Quantity 2 indicated.]
STEP 5/ÉTAPE 5
Final tightening: Ensure all bolts are securely tightened. A screwdriver (not provided) may be needed for final adjustments.
[Diagram shows the completed chair. A screwdriver icon is present, suggesting final tightening. Quantity 4 indicated.]
COMPLETED/COMPLÉTÉ ✔️
[Image of the fully assembled accent chair.]
DO NOT TIGHTEN BOLTS UNTIL COMPLETELY ASSEMBLED
MADE IN VIETNAM/FABRIQUÉ AU VIETNAM
