Assembly Instruction - Accent Chair
Item No: 194840326816
Introduction
Thank you for purchasing this product. Please take time to read and follow the instructions below. Check that you have all parts and hardware before assembly. Parts apparently missing are often found in the packing materials. If you do not have all the parts listed, have your dealer contact us and they will be sent to you immediately.
It is recommended to install protective pads under all legs and supports to avoid damage or scratches when placing furniture on a wood floor or other hard surface, and to prevent indentation and discoloration if placing on carpet.
Hardware may loosen over time. Periodically check to make sure all connections are tight. Re-tighten if necessary.
Parts List
| No | Description | Sketch | Qty |
|---|---|---|---|
| A | Back Rest / Dossier | [Back Rest Sketch] | 1 PC |
| B | Seat / Siège | [Seat Sketch] | 1 PC |
| C | Lsf Arm / Bras Gauche | [Left Arm Sketch] | 1 PC |
| D | Rsf Arm / Bras Droite | [Right Arm Sketch] | 1 PC |
| E | Cross Bar Front / Barre Transversale | [Front Cross Bar Sketch] | 1 PC |
| F | Cross Bar Back (Btm) / Barre Transversale | [Bottom Back Cross Bar Sketch] | 1 PC |
| G | Cross Bar Back (Top) / Barre Transversale | [Top Back Cross Bar Sketch] | 1 PC |
Hardware List
| No | Description | Sketch | Qty |
|---|---|---|---|
| 1 | Jcbc Bolt / Boulon M6 x 70mm | [Jcbc Bolt Sketch] | 8 PCS |
| 2 | Jcbc Bolt / Boulon M6 x 40mm | [Jcbc Bolt Sketch] | 2 PCS |
| 3 | Flat Washer / Rondelle Plate M6 x 19mm | [Flat Washer Sketch] | 2 PCS |
| 4 | Wood Dowel / M8 x 30mm | [Wood Dowel Sketch] | 10 PCS |
| 5 | Barrel Nut M6 / Doigts En Travers M6 x 13mm | [Barrel Nut Sketch] | 4 PCS |
| 6 | Allen Key / Clè Allen Wrench M4 | [Allen Key Sketch] | 1 PC |
*Above hardware are packed in carton for assembly. Le quincaillerie est dans carton pour l'assemblage.
Assembly Steps
Please assembly on smooth surface.
Step 1 / Étape 1
Insert dowels (4) into parts E, F, and G.
[Diagram showing dowels being inserted into parts E, F, and G]
Step 2 / Étape 2
*Do not fully tighten JCBC for this step.
[Diagram showing parts A and B being connected with bolts (2) and washers (3), secured with Allen Key (6). Close-up shows connection points.]
Step 3 / Étape 3
*Do not fully tighten JCBC for this step.
[Diagram showing parts A, B, C, and G being connected using bolts (1), barrel nuts (5), and Allen Key (6). Close-ups show connection details.]
Step 4 / Étape 4
*Do not fully tighten JCBC for this step.
[Diagram showing parts A, B, C, D, E, and F being connected using bolts (1), barrel nuts (5), and Allen Key (6). Close-ups show connection details.]
Step 5 / Étape 5
*Fully tighten JCBC bolts after all part in position.
[Diagram showing the completed chair assembly, with a callout indicating to fully tighten all JCBC bolts.]
Assembly Complete / Assemblage Complete
Made in Malaysia / Fabriqué en Malaisie
