Dewenwils Outdoor Light Sensor Countdown Timer with Lighting Program

Product Overview

This document provides instructions for the Dewenwils Outdoor Light Sensor Countdown Timer with Lighting Program.

Contact Information:

Email: support@dewenwils.com

Please include your Order ID when contacting customer support for faster service. Support aims to respond within 24 hours.

WARNING

To reduce the risk of fire, electric shock, or personal injury, please strictly follow the instructions:

1. The timer must be mounted in a vertical position with the outlets facing downward and at least 2 feet above the ground level.
2. Note: The lighting program is suitable for traditional tungsten lamps or LED light strings only. It is NOT suitable for light strings with built-in lighting programs or power from motor devices.
3. Do not connect any devices that exceed the maximum ratings of the timer.
4. Do not immerse in water.
5. Children are not allowed to use the timer without supervision.
6. Do not disassemble or repair the product; only authorized service personnel should perform repairs.
7. Always unplug and store indoors when not in use.

Product Layout

The timer features the following components:

• 1. Timer Dial: Controls the timer settings (2 to 8 hours, dusk to dawn, or daily repeat function).
• 2. MODE Button: Selects light set programs (on, flash/fade, flash, chase).
• 3. Sensor: Turns the timer on at dusk and off at dawn.
• 4. LED Indicator:
  • on: Always on steady.
  • flash/fade: Flashing and fading.
  • flash: Flashing randomly.
  • chase: 3 outlets flashing in turn (activated when 2 or 3 outlets are used).
• 5. Outlets: Plug LED lamps or Tungsten lamps to be controlled by the timer into these outlets.

Diagram Description: A line drawing shows the outdoor timer unit. The top has a cord with a plug and a socket. The front panel has a large dial labeled 'SENSOR', '8Hrs', '6Hrs', '4Hrs', '2Hrs', 'OFF', and 'MODE'. Below the dial are buttons labeled 'MODE', 'on', 'flash/fade', 'flash', 'chase'. The brand name 'Jewenwils' is visible below the buttons. There are two outlets on the bottom of the unit. Numbered labels point to different parts of the timer.

Operation

Rotate the dial on the timer to select one of the following settings:

• OFF: No power.
• ON: Constant power.
• DUSK-DAWN: Turns on at dusk and off at dawn automatically.
• 2 Hrs: On at dusk, stays on for 2 hours.
• 4 Hrs: On at dusk, stays on for 4 hours.
• 6 Hrs: On at dusk, stays on for 6 hours.
• 8 Hrs: On at dusk, stays on for 8 hours.

*Cycle repeats every 24 hours.

*The function will start instantly when you cover the lighting sensor by moving the sensor switch.

Notes

1. The timer operates on a daily repeat cycle. In case of power failure, it will stop operating. Once power is restored, reset the desired operating mode as per the instructions.
2. Once programming activates at dusk in the 2H, 4H, 6H, or 8H Mode, the program cycle will repeat until the timer is reset. External light sources like headlights, porch lights, or street lamps will not interfere with the active timer program.
3. In the Dusk-Dawn Mode, temporary light sources like headlights, porch lights, and other external light sources will not interfere with the photocell function unless the external light source is on for more than 15 minutes. In that case, the timer will shut off until darkness is restored.
4. When set to “ON”, the timer will provide continual power to attached devices until the timer is switched to “OFF” or any other operating mode.

Specifications

• Input Voltage: 125VAC, 60Hz.
• Max Power Rating For Each Receptacle: 125V, 60Hz, 337.5W, 2.7A.
• Cord: SJTW 18/3 AWG.

Safety Information

Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

One Year Limited Warranty

DEWENWILS warrants this product to be free from defects in material and workmanship for a period of one year from the date of purchase. Warranty is void if damage is caused by misuse or improper installation.

Email: support@dewenwils.com. Our dedicated customer service team will get back to you within 24 hours.

Compliance Marks: CULUS LISTED, Recycling symbol, Waste bin with cross symbol. Made in China.

Important Usage Warning

The timer has 10 heat emission holes on the back. Please do not hang it upside down in rainy days to prevent water from pouring in.