Dewenwils Outdoor Digital Yard Stake Timer
Model: HOYS22A
Instruction Manual
Thank you for your purchase. For any problems, please contact Dewenwils via email at support@dewenwils.com. Please include your User Name or Order ID for better assistance.
Warning: Safety Instructions
To reduce the risk of fire, electric shock, or personal injury, strictly follow these instructions:
- Do not connect any devices that exceed the maximum ratings of the timer.
- Do not immerse the timer in water.
- Children are not allowed to use the timer without supervision.
- Do not disassemble or repair the product; only authorized service personnel should perform repairs.
- Always unplug the timer and store it indoors when not in use.
- To prevent suffocation and choking, keep packaging materials away from children.
Installation
The timer unit attaches to the stake. Align the four tabs on the stake with the four corresponding holes on the back of the timer. Push the tabs down, then up, until they lock into place. This assembly is similar to a vertical unit with a stake extending downwards from its base.
Tips: If the ground is too hard to insert the stake, digging a hole that matches the stake with a hard object is recommended.
Product Layout
The timer unit features several key components:
- Indicator: A display screen showing time and program settings.
- Overload Protection Switch: A button or switch, typically on the side, to reset in case of overload.
- Outlets: Multiple electrical outlets, usually on the front or sides, for connecting devices.
The device is a rectangular unit with a digital display at the top, an overload protection switch on one side, and multiple three-prong outlets on the front face. A power cord extends from the bottom, leading to a stake attachment.
Operating Instructions
Before initial use, plug the timer in for at least 30 minutes to charge its internal battery. The unit is ready for programming once the screen displays.
1. Reset
Before programming, all settings should be reset. The reset hole, identified by "R", is located just below the “R/RECALL” button. Use a paper clip or ballpoint pen to press it. The display will show a default time like "88:88" with all days of the week (MO TU WE TH FR SA SU) and "PROG AUTO ON OFF" indicators, then after a few seconds, it will clear to "00:00" with only "MO" and "AUTO OFF" indicators.
2. Set the Current Time
- Keep the “CLOCK” button pressed throughout the setting operation.
- Press the “HOUR” button to set the hours.
- Press the “MIN” button to set the minutes.
- Press the “WEEK” button to select the correct day of the week.
- Release the “CLOCK” button. The time will be set.
3. ON/OFF Program Setting
There are a total of 20 ON/OFF settings available.
- Press the “PROG” button once. The display will show a program slot (e.g., "1 ON") with day indicators (MO TU WE TH FR SA SU) and a blank time.
- Press the “HOUR” or “MIN” buttons to set the ON time.
- Press the “WEEK” button to select the day(s) for this program. Available options include:
- MO,TU,WE,TH,FR,SA,SU (Every day)
- MO (Monday)
- TU (Tuesday)
- WE (Wednesday)
- TH (Thursday)
- FR (Friday)
- SA (Saturday)
- SU (Sunday)
- SA,SU (Weekend)
- MO,WE,FR (Monday, Wednesday, Friday)
- MO,TU,WE (Monday, Tuesday, Wednesday)
- TH,FR (Thursday, Friday)
- SU (Sunday)
- MO,TU,WE,TH,FR (Weekdays)
- MO,TU,WE,TH,FR,SA (Monday-Saturday)
- TU,TH,SA (Tuesday, Thursday, Saturday)
- TH,FR,SA (Thursday, Friday, Saturday)
- Press the “PROG” button to save the ON setting and proceed to the corresponding "1 OFF" setting. The display will show "1 OFF" with day indicators and a blank time.
- Repeat steps a-e to set ON/OFF times. Pressing the “PROG” button again will advance to the other 19 ON/OFF settings.
Note: The timer should operate in the “AUTO ON” or “AUTO OFF” mode. Refer to the "Switching Mode Indication" section.
4. Reset Button (Program)
- Press the “PROG” button to select the specific ON/OFF setting that needs to be changed.
- Press the “R/RECALL” button to reset the current ON/OFF setting without having to scroll through all the hours. The display for a program setting (e.g., "PROG 20 ON SA SU 8:00") will reset to a blank time (e.g., "PROG 20 ON SA SU --:--").
5. Switching Mode Indication
The current operating mode is shown on the display as “ON”, “AUTO ON”, “OFF”, or “AUTO OFF” along with the time of day. Press the “ON/AUTO/OFF” button to cycle through and adjust to the desired setting mode.
- ON: Always ON.
- OFF: Always OFF.
- AUTO ON: Timer is currently ON, and the ON/OFF program is activated.
- AUTO OFF: Timer is currently OFF, and the ON/OFF program is activated.
6. Manual Override Setting
As an independent programming feature, it is possible to advance to the next switching command at any given time by continuously pressing the “MANUAL” button. The display will cycle through modes: AUTO OFF → ON → AUTO ON → OFF.
7. Daylight Saving Time (DST)
Press and hold the “CLOCK” button for 3 seconds to advance the current time by 1 hour; a “+1h” icon will appear on the display. Press and hold the “CLOCK” button for 3 seconds again to decrease 1 hour, and the “+1h” icon will disappear. For example, a display showing "TH 8:00" will change to "TH 9:00" with a "+1h" indicator.
8. Power Back-up Feature
In the event of a power failure, the timer will retain its settings for an estimated 3 months if the power backup is fully charged.
Caution
- Risk of Fire: Not for permanent installation. Use only with outdoor equipment, Christmas trees, or other seasonal decorative-lighting products with a total maximum of 13 Amperes. Do not install or use this product for more than a 90-day period.
- If using Christmas tree or decorative lighting products not marked with an ampere rating, connect no more than 140 screw-base lamps (C7 or C9) or 12 strings with midget (push-in) lamps to this cord set.
- Cord sets must be plugged into a GFCI-protected receptacle.
- If using an outdoor-use cord set for an extended period (greater than 90 days), consider hard wiring a permanent outdoor-use receptacle rated for year-round use in the area where power is needed. Contact a licensed electrician for proper installation of permanent wiring.
- After installation, the connector must be maintained a minimum of 6 inches above ground.
Specifications
| Feature | Detail |
|---|
| Input Voltage | 120VAC 60Hz |
| Cord | SJTW 14/3C |
| Max. Current | 15A Resistive |
| Wattage | 1000W Tungsten |
| Horsepower | 1 HP |
One Year Limited Warranty
Dewenwils warrants this product to be free from defects in material and workmanship for a period of one year from the date of purchase. The warranty is void if damage is caused by misuse or improper installation. For any questions, contact Dewenwils via email at support@dewenwils.com. The dedicated customer service team aims to respond within 24 hours.
