DiO 54863 Remote Control

Video Tutorial

For simplified understanding and installation of DiO packs and solutions, video instructions are available on our YouTube channel.

Watch at: youtube.com/c/dio-connected-home ▶️

1. Prepare the Remote Control

Open the small compartment on the back of the remote control and remove the tab from the battery.

1.1 Changing the Battery

Follow these steps to replace the battery:

1. Insert a 3/5 mm flathead screwdriver into the small slot above the battery compartment and pull the cover down to open it. [Illustration: Remote back with slot, cover being opened]
2. Replace the old battery with a new 3V CR2450 battery, ensuring the '+' terminal is facing upwards. [Illustration: Battery compartment with CR2450 battery, '+' terminal up]
3. Close the battery compartment until you hear a click. [Illustration: Battery compartment closed]

Caution: ⚠️ Danger of explosion if the battery is not replaced correctly. Replace only with the same or equivalent type.

This product contains a button cell battery. If swallowed, it can cause severe internal burns in as little as 2 hours. Keep new and used batteries out of reach of children. If the battery compartment does not close properly, stop using the product and keep it away from children. If you suspect batteries have been swallowed or placed inside a body part, seek medical attention immediately.

2. Associating Your Remote with a DiO Receiver

The DiO Remote Control is compatible with all DiO receivers, including switches and modules.

2.1 Associating the Remote Control with a DiO 1.0 or DiO Connect Receiver

Steps:

1. Connect the module or switch and bring it close to the DiO remote control.
2. Put the DiO 1.0 or DiO Connect Receiver into learning mode. The LED indicator on the receiver will start to flash slowly. [Illustration: Receiver with flashing LED]
3. Within 12 seconds, press the [ON] button on the remote control. The LED on the remote control will flash rapidly for 1 second to confirm the association. [Illustration: Remote with ON button pressed, LED flashing rapidly]

Attention: If the [ON] button is not pressed within 12 seconds, the module/socket will exit learning mode. You must restart the association process from step 2.1.

2.2 Deleting the DiO 1.0 Receiver Remote Control

Steps:

1. Bring the remote control close to the DiO 1.0 socket, module, or outlet.
2. Put the DiO 1.0 Receiver into learning mode. The LED indicator on the receiver will start to flash slowly. [Illustration: Receiver with flashing LED]
3. Press the [v] button on the channel you wish to delete. The LED on the remote control will flash rapidly for 1 second to confirm deletion. [Illustration: Remote with specific channel 'v' button pressed, LED flashing rapidly]

3. Operation

To Open/Close: Press the [A] button to open or the [v] or [STOP] button to close your shutter.

To Stop Halfway: Press the [-] button to stop the shutter when the desired position is reached.

The remote control features automatic shutdown after 2 minutes of continuous use.

Controlling Different Shutters: Up to 5 shutters or groups of shutters can be controlled by the DiO remote control. Press the [CHAN] button on the remote control to cycle through channels. The selected channel number is confirmed by the number of LEDs illuminated on the remote control. [Illustration: Remote with CHAN button, LEDs indicating channel]

Centralization: The 6th channel automatically controls all shutters linked to channels 1 to 5. Press the [CHAN] button 6 times. The 5 LEDs on the remote will flash red once, then press [^] or [v] to open or close all your shutters simultaneously. [Illustration: Remote with CHAN button pressed multiple times, LEDs flashing red]

4. Troubleshooting

Issue: The receiver is not activated when the remote control is pressed.

Possible Solutions:

• Check the battery polarity and ensure it is not depleted.
• Verify that the remote control is correctly associated with the receiver and that the receiver is properly connected.
• Check the status of the receiver's memory (refer to the receiver's manual for details).

Important Notes:

• The effective range between the receiver and the remote control is up to 50 meters, but this can be reduced by wall thickness or a congested wireless environment.
• Maintain a minimum distance of 1-2 meters between two DiO receivers (modules, sockets, or bulbs) to prevent interference.
• Do not use the device in damp locations.

5. Technical Data

Specifications

• Protocol and Frequency: 433.92 MHz by DiO
• Max. Power: 0.5 mW ERP
• Range with DiO 1.0 Receiver: 50m (in free field)
• Operating Temperature: -5°C to +40°C
• Battery: Lithium CR2450 3V (included)
• Number of Channels: 3 + 1 group
• Dimensions: 117 x 37 x 9mm
• Usage: Indoor use (IP20), not suitable for humid environments.

Conformity and Recycling

Recycling: ♻️ Do not dispose of batteries or out-of-order products with household waste. Hazardous substances they may contain can harm health or the environment. Return these products to your retailer or use the selective waste collection services provided by your municipality.

EU Declaration of Conformity:

Hereby, Chacon declares that the radio equipment type 54863 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: www.chacon.com/conformity

6. Complete Your Installation

Enhance your home automation setup with DiO solutions for controlling lighting, roller shutters, garden features, or for home surveillance with video monitoring. DiO connected home solutions are easy to install, high-quality, scalable, and economical. Discover the full range at www.diohome.com.